PanelDue no longer connecting on Duet3/io0 with 3.01-RC11

gtj0

@bearer Maybe if you jumper io0.in to io1.in both ports will get the paneldue commands.

Nuramori

The ultimate goal maybe/would be to negate the arduino entirely and use the Pi4 to drive the neopixels. I am digesting the way that could be done by using the API to pull the same info that is used in the JSON package to the Paneldue.

gtj0

@Nuramori There's a command /opt/dsf/bin/ModelObserver that spits out json as its updated by the Duet. All you have to do is keep reading that.

A Former User

@gtj0 said in PanelDue no longer connecting on Duet3/io0 with 3.01-RC11:

@bearer Maybe if you jumper io0.in to io1.in both ports will get the paneldue commands.

probably, but i think thats what Nuramori was suggesting?

@Nuramori said in PanelDue no longer connecting on Duet3/io0 with 3.01-RC11:

sniffing and parsing the JSON package for the time to complete, the bed temp, and the extruder(s) temps.

yeah, you could just send M408 with different S paramters in DWC to see which one returns all you need and have the arduino send that string at regular intervals and keep the parsing code as is.
https://duet3d.dozuki.com/Wiki/Gcode#Section_M408_Report_JSON_style_response

The Pi route may be easier, if not maybe less reliable until the DSF stuff matures.

A Former User

btw
@gtj0 said in PanelDue no longer connecting on Duet3/io0 with 3.01-RC11:

Oh, one other thing, io1.out can also be configured as a uart so you may want to use that for the Arduino.

@gtj0 said in RRF 3.01-RC11 DSF mode: io_1 not outputting "ok" consistently:

Marlin mode and raw mode on io_1...
M555 P2
M575 P1 B115200 S2

was wondering if the typo was io_1 or P1, should be P2? (never mind, saw P2 a bit further up here)

gtj0

@bearer Unfortunately it looks like the uart on io1 is disabled in firmware. So P0 is the USB port, P1 is io0 and P2 returns Error: M575: parameter 'P' too high

Maybe @dc42 can enable it in a future release.

Nuramori

I'm always up to trying anything; out of pure curiosity, I am interested in what changed that would prevent both devices from sharing the data on io0.out, when it worked prior to RC11, without any hardware changes.

gtj0

@Nuramori said in PanelDue no longer connecting on Duet3/io0 with 3.01-RC11:

I'm always up to trying anything; out of pure curiosity, I am interested in what changed that would prevent both devices from sharing the data on io0.out, when it worked prior to RC11, without any hardware changes.

I'm guessing there was a drive strength change or something. I can't get to the source code right now but I can check tomorrow if @dc42 hasn't answered by then.

Nuramori

I'm guessing there was a drive strength change or something. I can't get to the source code right now but I can check tomorrow if @dc42 hasn't answered by then.

Interesting. I wasn't aware that something like that was controllable through software. Thanks for the help @gtj0 .

gtj0

@Nuramori said in PanelDue no longer connecting on Duet3/io0 with 3.01-RC11:

I'm guessing there was a drive strength change or something. I can't get to the source code right now but I can check tomorrow if @dc42 hasn't answered by then.

Interesting. I wasn't aware that something like that was controllable through software. Thanks for the help @gtj0 .

Yeah on most "microcontroller" platforms, including the ones on the Duets, Pis and other SBCs, many pins are general purpose and have their function (uart, GPIO, SPI, etc) and capabilities (input, output, both, drive strength, pull up/pull down, tristate, etc) controlled from software.

A Former User

couldn't spot any changes to low level functions, just some conditional logic around the higher level initilization.
https://github.com/dc42/RepRapFirmware/commit/6f912e9ca47930d7b91d504c0e9c8be31251284a#diff-52cb419324e9c23a2e2c5a269e0e70fcR3581

0

dc42 committed to dc42/RepRapFirmware

Various changes for 3.01-RC11

Tool change files are now run even if axes have not been homed
PanelDue replies are now sent immediately instead of being saved for
retrieval by M408
Added aux raw mode
On Duet 3, IO_0 is not configured in serial mode until M575 P1 is
executed
GCodeException class now stores a small string to allow more meaningful
error messages

Nuramori

Could it be this?

setPullup(APIN_Serial0_RXD, true);

I didn’t see anywhere else where the pull-up resistor is used/set in the old code, could the setting the pull-up affect the signal enough that it “dies” enough in signal strength for two electrical connections to be too much for the paneldue circuitry?

A Former User

@Nuramori said in PanelDue no longer connecting on Duet3/io0 with 3.01-RC11:

setPullup(APIN_Serial0_RXD, true);

click the beginning of the line and choose "git blame" to see when it was changed. (if viewed on github, otherwise git cli works as well)

i'm guessing its part of the other repositories then

gtj0

@Nuramori said in PanelDue no longer connecting on Duet3/io0 with 3.01-RC11:

Could it be this?

setPullup(APIN_Serial0_RXD, true);

I didn’t see anywhere else where the pull-up resistor is used/set in the old code, could the setting the pull-up affect the signal enough that it “dies” enough in signal strength for two electrical connections to be too much for the paneldue circuitry?

Absolutely!
I just did a build without the pullup. See this helps...
http://dueui.org/download/Duet3Firmware_MB6HC.bin

gtj0

@bearer It was new in the last 2 commits.

A Former User

(for CoreNG, ofc, my bad)

Nuramori

@gtj0 I downloaded the file, pushed it to the printer, and performed a "M997 S0"

Result was :
Error: Operation failed (Reason: ArgumentNullException in SimpleCode: Value cannot be null. (Parameter 'input'))

A Former User

But without the pull up? Comment said it was removed pending a M575, so the fix would be to enable it upon finding a M575 P1 command?

gtj0

@Nuramori Eh? I just did it myself and it worked. Maybe try to download again?
@bearer Yeah I just removed it altogether to see if it helps. If it doesn't then the issue is elsewhere.

Nuramori

unfortunately, my hopes were higher. No change.