cube comes out 3x taller
-
Hi!
I own ender3 pro with default extruder and almost direct extruder (6cm Bowden).
When I print 20mm cube it comes out 3x taller (z axis). With no underextrusion present
I'm using default ender3 config from configurator
; Drives M569 P0 S0 T0.1:0.1:0.02:0.02 ; physical drive 0 goes backwards using TMC220x driver timings M569 P1 S0 T0.1:0.1:0.02:0.02 ; physical drive 1 goes backwards using TMC220x driver timings M569 P2 S1 T0.1:0.1:0.02:0.02 ; physical drive 2 goes forwards using TMC220x driver timings M569 P3 S0 T0.1:0.1:0.02:0.02 ; physical drive 3 goes backwards using TMC220x driver timings M584 X0 Y1 Z2 E3 ; set drive mapping M92 X80.00 Y80.00 Z400.00 E96.50 ; set steps per mm M566 X1200.00 Y1200.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min) M203 X9000.00 Y9000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min) M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2) M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) M84 S30 ; Disable motor idle current reduction
Do you have any tips?
-
@rudenick Please post your complete config.g
-
; Configuration file for SKR v1.4 (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2.1.4 on Wed Apr 22 2020 19:45:44 GMT+0200 (Central European Summer Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Ender1" ; set printer name ; Network M552 S0 ; disable network ; Drives M569 P0 S0 T0.1:0.1:0.02:0.02 ; physical drive 0 goes backwards using TMC220x driver timings M569 P1 S0 T0.1:0.1:0.02:0.02 ; physical drive 1 goes backwards using TMC220x driver timings M569 P2 S1 T0.1:0.1:0.02:0.02 ; physical drive 2 goes forwards using TMC220x driver timings M569 P3 S0 T0.1:0.1:0.02:0.02 ; physical drive 3 goes backwards using TMC220x driver timings M584 X0 Y1 Z2 E3 ; set drive mapping M92 X80.00 Y80.00 Z133.00 E96.50 ; set steps per mm M566 X1200.00 Y1200.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min) M203 X9000.00 Y9000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min) M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2) M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) M84 S30 ; Disable motor idle current reduction ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X235 Y235 Z260 S0 ; set axis maxima ; Endstops M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop ; Z-Probe M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed M557 X15:215 Y15:195 S20 ; define mesh grid ; Heaters M140 H0 ; remap heated bed to heater 0 M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bed" T0 ; create bed heater output on bed and map it to sensor 0 M143 H0 S80 ; set temperature limit for heater 0 to 150C M307 H0 M307 H0 A79.8 C282.4 D1.3 S1.0 V0.0 B0 ; disable bang-bang mode for the nozzle heater and set PWM limit, update auto bed tuning M303 H0 S55 M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M143 H1 S250 ; set temperature limit for heater 1 to 275C M307 H1 A366.5 C138.0 D4.2 S1.0 V0.0 B0 ; disable bang-bang mode for the nozzle heater and set PWM limit, update auto bed tuning M303 H1 S250 ;Tuning results ;4/29/2020, 1:52:19 PM M307 H0 ;Heater 0 model: gain 340.0, time constant 140.0, dead time 5.5, max PWM 1.00, calibration voltage 0.0, mode PID ;Computed PID parameters for setpoint change: P13.4, I0.482, D51.4 ;Computed PID parameters for load change: P13.4, I0.949, D51.4 ;4/29/2020, 1:52:04 PM M307 H1 ;Heater 1 model: gain 365.3, time constant 135.6, dead time 1.6, max PWM 1.00, calibration voltage 0.0, mode PID ;Computed PID parameters for setpoint change: P40.7, I2.738, D46.4 ;Computed PID parameters for load change: P40.7, I7.255, D46.4 ; Heaters alternative ;M140 H0 ; remap heated bed to heater 0 ;M308 S0 P"bedtemp" Y"thermistor" T98801 B4185 ; configure sensor 0 as thermistor on pin bedtemp ;M950 H0 C"bed" T0 ; create bed heater output on e1heat and map it to sensor 0 ;M143 H0 S80 ; set temperature limit for heater 0 to 80C ;M307 H0 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit ;M308 S1 P"e0temp" Y"thermistor" T98801 B4185 ; configure sensor 1 as thermistor on pin e0temp ;M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 ;M143 H1 S250 ; set temperature limit for heater 1 to 260C ;M307 H1 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H1 T45 ; set fan 0 value. Thermostatic control is turned on M950 F1 C"e1heat" Q500 ; create fan 1 on pin e1heat and set its frequency M106 P1 H1 T45 S255 ; set fan 1 value. Speed is set to 255. Thermostatic control is off ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined ; Miscellaneous T0 ; select first tool
-
I changed the M92 Z400 to M92 Z221 and it seems allright but I would appreciate helping me understand the situation
-
@rudenick Just got this through the RRF Config tool, mine Ender3 is very different!
This line might help in your ;Drives section - its missing from your config
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
Your M92 should be this
M92 X80.00 Y80.00 Z400.00 E96.50HTH
Regards,
Paul.