PanelDue 4.3" never connects
-
@Chriss said in PanelDue 4.3" never connects:
11/05/2020, 00:58:54 M575 P0 B57600 S1
M575 P1 B57600 S1
is the config you want, P0 is for the USBconsideconsole afaik. -
@bearer said in PanelDue 4.3" never connects:
M575 P1 B57600 S1
is the config you want, P0 is for the USB conside afaik.And that is what I have, the "P0" was just to be on the save site for testing.
Any other idea?
Cheers, Chriss
-
Any other idea?
IIRC having two identical M575 commands was just a work around for non-standard baud rates and fixed in RC12, but you could try it.
Maybe post the complete config, maybe someone spots any changes the BL touch stuff could have done to IO_0?
Btw, you only need the 4 pin wire to get past "connecting", the ribbon is just for the SD card.
-
@bearer
That with the cable is clear, I just wanted to mention what I tried already.
I created a new configuration from scratch with the configtool to make sure that I did not messed up the configuration during my BLTouch journey (I used the "Creality Ender 3 Pro".) Still with the same problem.
config.g
; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue May 12 2020 16:59:30 GMT+0200 (Central European Summer Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Ender 3 Pro" ; set printer name M918 P1 E4 F2000000 ; configure direct-connect display ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S0 ; physical drive 0 goes backwards M569 P1 S0 ; physical drive 1 goes backwards M569 P2 S1 ; physical drive 2 goes forwards M569 P3 S0 ; physical drive 3 goes backwards M584 X0 Y1 Z2 E3 ; set drive mapping M350 Z128 I0 ; configure microstepping without interpolation M350 X16 Y16 E16 I1 ; configure microstepping with interpolation M92 X80.00 Y80.00 Z400.00 E93.00 ; set steps per mm M566 X1200.00 Y1200.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min) M203 X9000.00 Y9000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min) M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2) M906 X800 Y800 Z800 E1000 I50 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X310 Y310 Z400 S0 ; set axis maxima ; Endstops M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop M574 Z1 S2 ; configure Z-probe endstop for low end on Z ; Z-Probe M950 S0 C"duex.e5heat" ; create servo pin 0 for BLTouch M558 P9 C"zprobe.in+zprobe.mod" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height M557 X15:215 Y15:195 S20 ; define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M143 H0 S150 ; set temperature limit for heater 0 to 150C M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M143 H1 S275 ; set temperature limit for heater 1 to 275C M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency M106 P2 S1 H1:0 T45 ; set fan 2 value. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined
Do you need more?
Cheers, Chriss
-
-
@jay_s_uk
Not there, but it seams like it is the default. It is set to the expected parameters when I query "M575 P1". But I will try to add it tomorrow. -
@Chriss said in PanelDue 4.3" never connects:
@jay_s_uk
Not there, but it seams like it is the default. It is set to the expected parameters when I query "M575 P1". But I will try to add it tomorrow.Not after RC12
-
@bearer
Fiddlesticks!
From the RC12 WHATS_NEW_RRF3.md:
All PanelDue users: the PanelDue connector (or IO_0 on Duet 3) is no longer dedicated to PanelDue, therefore if you connect a PanelDue to this port you must use the following command in config.g to enable it: M575 P1 S1 B57600. You can use baud rates other than 57600, however the IAP files all assume 57600 baud; therefore if you use another baud rate then PanelDue will not display firmware update progress.To many things in parallel.....
I like the new behavior in "3.01":
If the serial aux port hasn't been enabled, M575 P1 with no other parameters now reports thisIt works now with the fresh generated config and I added "M575 P1 B57600 S1" to the config. I guess that the configtool should ask for a PanelDue and add this parameter than.
I will check my "actual" config now, it is proven that it must be a configuration problem.
Cheers, Chriss
-
@Chriss said in PanelDue 4.3" never connects:
I guess that the configtool should ask for a PanelDue and add this parameter than.
Very good point!
-
@Chriss said in PanelDue 4.3" never connects:
@jay_s_uk
Not there, but it seams like it is the default. It is set to the expected parameters when I query "M575 P1". But I will try to add it tomorrow.In 3.01-RC12 the M575 P1 command fails to tell you that the port is not enabled. The fix for that will be in the 3.01 release.