endstop trigger and bangbang questions

deltajegga

its still the same as up top except the last lines are

;M950 J1 C"!^duex.e2stop"
;M581 P1 T0 C0

Phaedrux

Can you send M115 and verify that you're actually running 3.1.1?
Also, can you send M98 Pconfig.g and report any errors?
Also the content of M122 report please.

Phaedrux

If you are running 3.1.1 your M581 does require an S parameter.

https://duet3d.dozuki.com/Wiki/Gcode#Section_M581_RepRapFirmware_3_01RC2_and_later

deltajegga

M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet WiFi 1.02 or later + DueX5 FIRMWARE_DATE: 2020-05-19b2

no errors on M98 other than my hotend sensor its not installed yet nor is the extruder motor.

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DLM-996RU-N8PS4-7J1F6-3SD6K-TUAZN
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 94324 of which 96 recycled
Exception stack ram used: 264
Never used ram: 8408
Tasks: NETWORK(ready,368) HEAT(blocked,848) DUEX(suspended,160) MAIN(running,1656) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:03:01 ago, cause: power up
Last software reset at 2020-06-20 13:22, reason: User, spinning module GCodes, available RAM 8252 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 28.2, current 35.2, max 35.3
Supply voltage: min 23.9, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Date/time: 2020-06-23 22:07:08
Cache data hit count 316873259
Slowest loop: 11.95ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.8ms, write time 6.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 22.99ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address bc:dd:c2:2d:67:63
WiFi Vcc 3.42, reset reason Unknown
WiFi flash size 4194304, free heap 19864
WiFi IP address 192.168.1.161
WiFi signal strength -53dBm, reconnections 0, sleep mode modem
Socket states: 0 4 0 0 0 0 0 0
=== DueX ===
Read count 3, 0.99 reads/min

deltajegga

i tried

M950 J1 C"!^duex.e2stop"
M581 P1 T0 C0 S1

still a no go. heres a picture, the red switch on top goes from white/green to two white wires down to the duex endstop. it has 3 wires for NC or NO, but i assume that doesn't really matter with the inversion capability. if feel like im missing something obvious.

Phaedrux

It's hard to tell from the photo of the wiring bundle but have you followed the Duex wiring guide on connecting the grounds with a short piece of wire as shown here? https://duet3d.dozuki.com/Wiki/Duex2_and_Duex5_Features#Section_Wiring

Can you send echo sensors.gpIn[1].value and report the results?

deltajegga

yes its wired the same.
i get this back

Error: meta command: array index out of bounds

Phaedrux

@deltajegga said in endstop trigger and bangbang questions:

;M950 J1 C"!^duex.e2stop"
;M581 P1 T0 C0

You've uncommented these lines right?

@deltajegga said in endstop trigger and bangbang questions:

i get this back
Error: meta command: array index out of bounds

means gpIn[1] doesn't exist, so either the M950 J1 command wasn't run or it didn't work

What do you get if you send just M950 J1 in the console?

deltajegga

hahaha, silly me. i guess it would help if i uncommented them.
ok i get a value of 0 back.

and if i send the m950 j1 i get back
Pin !duex.e2stop, active: false

Phaedrux

@deltajegga said in endstop trigger and bangbang questions:

M950 J1 C"!^duex.e2stop"
M581 P1 T0 C0 S1

And with this? Does it work as expected?

deltajegga

no, it still resetes if i home

Phaedrux

I wonder if having the wiring bundled like that is causing the e stop switch pick up the signal from the endstop.

Usually when I'm making my looms I always twist the wires to try and prevent cross talk. Can you physically separate the wiring for the e stop from the bundle and test again?

deltajegga

ok, interesting. so that solved the triggering when it shouldent problem. (i allways thought that only pwm and data lines cared about twisting.)

but it still wont trigger when i press the button. just a reminder im using a normally open switch.

Phaedrux

@deltajegga said in endstop trigger and bangbang questions:

just a reminder im using a normally open switch.

Try changing it to normally closed. This should be configurable with the S0 S1 switch, but it's worth a shot.

@deltajegga said in endstop trigger and bangbang questions:

(i allways thought that only pwm and data lines cared about twisting.)

I twist or braid everything when using cramped conduits. Just as a matter of habit.

deltajegga

yeah still nothing.

Phaedrux

And you're sure the switch really works?
Do you have a regular endstop microswitch you can connect in its place to test?

deltajegga

yeah i tested it with a multimeter at the plug on the duex.

droftarts

@deltajegga In RRF 3.1.1, the 'C' parameter has changed to 'R'. See https://duet3d.dozuki.com/Wiki/Gcode#Section_M581_RepRapFirmware_3_01RC2_and_later

Try changing command to M581 P1 T0 R0 S1

Ian

deltajegga

damn, got my hopes up. i tried that with !, ^, and !^ on the pin name but still nothing. here is a refresh of the config.

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.1 on Sun May 31 2020 21:54:40 GMT-0700 (Pacific Daylight Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"1M"                                         ; set printer name



; Network
M552 S1                                            ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet
M587 S"MTS" P"Judy1985"


; Drives
M569 P0 S0                              ; physical drive 0 goes backwards  X
M569 P1 S0                              ; physical drive 1 goes forwards   RY
M569 P2 S0                              ; physical drive 2 goes backwards  RZ
M569 P3 S0                              ; physical drive 3 goes forwards   E
M569 P5 S1                              ; physical drive 5 goes forwards   LY
M569 P6 S0                              ; physical drive 6 goes backwards  LZ

M584 X0 Y1:5 Z6:2 E3                                     ; set drive mapping

M350 X16 Y16:16 Z16:16 E16 I1                            ; configure microstepping with interpolation

M92 X114.29 Y114.29:114.29 Z400.00:400.00 E420.00        ; set steps per mm

M566 X300.00 Y300:300 Z12:12 E120.00                     ; set maximum instantaneous speed changes (mm/min)

M203 X4000.00 Y4000:4000 Z500:500 E1200.00               ; set maximum speeds (mm/min)

M201 X150.00 Y150:150 Z20:20 E250.00                     ; set accelerations (mm/s^2)
  
M906 X800 Y1100:1100 Z600:600 E800 I50                   ; set motor currents (mA) and motor idle factor in per cent
M84 S90                                                  ; Set idle timeout




; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis min
M208 X1400 Y880 Z900 S0                            ; set axis max

; Endstops
M574 X1 S1 P"xstop"                                ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                                ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2                                         ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"duex.e2heat"                             ; create servo pin 0 for BLTouch
M558 P9 C"zprobe.in+zprobe.mod" H10 F400 T8000      ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X28.3 Y0 Z1.3                             ; set Z probe trigger value, offset and trigger height    INCREASE Z TO MOVE CLOSER TO BED
M557 X50:1380 Y50:870 S100                          ; define mesh grid


; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138     ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                              ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 A137 D6.4 C1400                   ; enable PID mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
                    

M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138      ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                               ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit



; Fans
M950 F0 C"fan0" Q500                               ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C



; Miscellaneous

M671 X50:1480 Y400:400 S10                         ; x gantry leveling


M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0                                                 ; select first tool


M950 J1 C"duex.e2stop"
M581 P1 T0 R0 S1                              ;emergency stop