Smart effector first layer issues
-
Ok, adjusted the Z height, now it just grips the paper @ Z0.1
-
@Lakeman
Cool so when you G28 ,G1 Z0.1 at 60c bed temp it goes to Z0.1 ? just touches the paper not grip it -
-
Good stuff was it off ? if so by how much ? just good to know..
Copy below to new macro, so macros, new macro ...good to keep
call it probe offset and run it its safe given to me by another user on this forum; Heat bed to 60C & nozzle to 130C
M104 S130 T0
M190 S60 T0
M109 S130 T0
M106 P2 S0
G31 P100 X0 Y0 Z0 ; Reset Z trigger height to 0mm
M290 R0 S0 ; Reset babystepping
G29 S2 ; Clear bed mesh
G28 ; Home the effector
G1 X0 Y0 Z20 F6000 ; Move close to the bed
G30 ; Probe to find a rough Z 0mmG1 X0 Y0 Z1 F3000 ; Move the nozzle to Z 1mm slowly
G92 Z3.0 ; Set the Z height to 3mm, allowing moves below 0
M291 P"Lower the nozzle to until it touches a 0.10mm shim. Click to continue." S2 Z1
G92 Z0 ; Define this point as 0mm
G1 X0 Y0 Z20 ; Move the probe to Z 20mm
G30 S-3 ; Probe and set the trigger height
G1 Z20 ; Raise Z to 20mm -
About 1.5mm out
-
That's a lot mate
-
Oke, I ran the macro. This time it touched the paper @Z2.1... But before was a cold nozzle
-
Nozzle won't make that much difference ...what was the offset ?
-
touching the paper at Z2.15
-
M292
Z probe trigger height set to -0.241 mm -
-2mm from M665 H please we can add it back if needed and run it again please
when you start your machine the effector does flash 2 times yeah?
-
It flashes 3 times at startup
I removed 2mm again, but paper bites at the same spot, becouse it probes first I think?
result:
M292
Z probe trigger height set to -0.153 mm -
The probing also go's a bit fast and really taps the bed, should this not go a bit more gentle?
-
@Lakeman
Thats fine no it wants a good tap mmine is set the same ...Did you mention you reset the sens of the effector with
M672 S131:131 ?Z probe trigger height set to -0.153 mm is much closer to my set up
New macro ...call it repeat probe testG28
G30 P0 X0 Y0 Z-9999
G30 P1 X0 Y0 Z-9999
G30 P2 X0 Y0 Z-9999
G30 P3 X0 Y0 Z-9999
G30 P4 X0 Y0 Z-9999
G30 P5 X0 Y0 Z-9999
G30 P6 X0 Y0 Z-9999
G30 P7 X0 Y0 Z-9999
G30 P8 X0 Y0 Z-9999
G30 P9 X0 Y0 Z-9999 S-1 -
No, it is set @ S105:30:225
-
M672 not sure it works ? see what it says
-
M98 P"0:/macros/repeat probe test"
G32 bed probe heights: -1.875 -1.863 -1.863 -1.863 -1.863 -1.875 -1.863 -1.875 -1.875 -1.875, mean -1.869, deviation from mean 0.006 -
-
During the delta calibration and mesh it goes much more gentle still, should that tap at the same speed?
-
Print with or without mesh?
