Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Duet3 + Pi DWC freezing

    Scheduled Pinned Locked Moved Solved
    Duet Web Control
    6
    48
    2.0k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Carloundefined
      Carlo @Carlo
      last edited by

      @Carlo

      Works OK in stand alone

      https://www.youtube.com/watch?v=mCwJnyaidI4

      Phaedruxundefined 1 Reply Last reply Reply Quote 0
      • Phaedruxundefined
        Phaedrux Moderator @Carlo
        last edited by

        @Carlo Under investigation.

        Z-Bot CoreXY Build | Thingiverse Profile

        Carloundefined 1 Reply Last reply Reply Quote 0
        • Carloundefined
          Carlo @Phaedrux
          last edited by

          @Phaedrux

          Cheers

          Carloundefined 1 Reply Last reply Reply Quote 0
          • Carloundefined
            Carlo @Carlo
            last edited by

            @Carlo

            So received my new Duet 3 yesterday so new board new cable new installation DuetPi
            nothing else attached same issue works perfectly in stand alone and does everything in SBC mode but print ...If I use DuetPi it will start the print then head to the endstops but wont stop at them after a few seconds but if I build PiOs install DSF etc it heads the other way and ploughs in to the bed but at the same point everytime after a few seconds to the mm?
            with the motors screeming and M122 shows no errors everything is peachy as far as the board is concerned ...Turns out its the purge line in my start code.. which works fine in standalone mode but not SBC SBC "worked" without it Huh? Quotes well A print
            Is it the spacing of the lines printing at the moment so can't retry right now but like to know how it ends.
            any ideas ?
            ; Draw arc to prime the nozzle between 6PM and 9PM on the bed edge

            G1 X0 Y-175 Z0.25 F6000

            G2 X-175 Y0 I0 J175 E30 F1500

            G1 X-174.52

            G3 X0 Y-174.52 I174.52 J0 E28 F1500

            Cheers
            C

            Phaedruxundefined chrishammundefined 2 Replies Last reply Reply Quote 0
            • Phaedruxundefined
              Phaedrux Moderator @Carlo
              last edited by

              @Carlo Interesting. I guess it doesn't like the arc.

              Z-Bot CoreXY Build | Thingiverse Profile

              1 Reply Last reply Reply Quote 0
              • chrishammundefined
                chrishamm administrators @Carlo
                last edited by

                @Carlo Can you please upload the full file?

                Duet software engineer

                Carloundefined 1 Reply Last reply Reply Quote 0
                • Carloundefined
                  Carlo @chrishamm
                  last edited by Carlo

                  @chrishamm

                  Its any with that start code so here you go a small one it gets about 10mm in to the purge arc then thats all she wrote

                  Predator_rail_align_guide_v2higher.gcode

                  chrishammundefined 1 Reply Last reply Reply Quote 0
                  • chrishammundefined
                    chrishamm administrators @Carlo
                    last edited by

                    @Carlo Thanks for the file. I could provoke an error that will be fixed in v3.2 but I am not sure if it is related to the problem you reported. I'll try your G2 code on Monday when I get back and report my findings.

                    Duet software engineer

                    Carloundefined 2 Replies Last reply Reply Quote 0
                    • Carloundefined
                      Carlo @chrishamm
                      last edited by

                      @chrishamm

                      Only posted in case its of help to you guys if it is actually a bug ...now with leaving it out of my slicer my SBC setup is printing beautifully and I simply set 0.5mm unretract before start of print so no purge needed in PSlicer so all good.

                      Cheers
                      C

                      1 Reply Last reply Reply Quote 1
                      • Carloundefined
                        Carlo @chrishamm
                        last edited by

                        @chrishamm

                        Hi Chris,

                        Just thought I would let you know the latest update fixed the issue.

                        Cheers
                        C

                        chrishammundefined 1 Reply Last reply Reply Quote 1
                        • chrishammundefined
                          chrishamm administrators @Carlo
                          last edited by

                          @Carlo Great, thanks for letting me know!

                          Duet software engineer

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA