M701 causes reboot 3.2-beta2

TC

Hi I don't know what is going on but when I try to use the M701 or the Load filament option in DWC the Duet Ethernet with RRF 3.2-beta2 reboots. Is it possible there is a bug in the new version?

Phaedrux

Can you capture a M122 after the reboot?

TC

@Phaedrux

M122

=== Diagnostics ===

RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2-beta2 running on Duet Ethernet 1.02 or later + DueX5

Board ID: 08DGM-917NK-F2MSW-6JKDG-3S86T-KZ5ND

Used output buffers: 1 of 24 (13 max)

=== RTOS ===

Static ram: 24028

Dynamic ram: 96364 of which 44 recycled

Exception stack ram used: 200

Never used ram: 10436

Tasks: NETWORK(ready,137) HEAT(blocked,308) DUEX(blocked,36) MAIN(running,445) IDLE(ready,19)

Owned mutexes:

=== Platform ===

Last reset 00:01:36 ago, cause: software

Last software reset at 2020-10-08 18:22, reason: AssertionFailed, GCodes spinning, available RAM 10436, slot 0

Software reset code 0x4123 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0x20004264 Task MAIN

Stack: 0000059e 004716a8 00450849 0000000d ffffffff 20000db0 4d454144 200032a8 ffffffff 00000000 20002eb4 a5a5a5a5 004508cb 200042b0 0045e98c 20007940 0044e14f 200042cc 00446049 2000329c 200042cc 00000001 200042d4 00000000 004460b3 000000c8 200042d4

Error status: 0x00

MCU temperature: min 34.4, current 35.2, max 35.4

Supply voltage: min 24.1, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes

Driver 0: position 0, standstill, SG min/max not available

Driver 1: position 0, standstill, SG min/max not available

Driver 2: position 0, standstill, SG min/max not available

Driver 3: position 0, standstill, SG min/max not available

Driver 4: position 0, standstill, SG min/max not available

Driver 5: position 0, standstill, SG min/max not available

Driver 6: position 0, standstill, SG min/max not available

Driver 7: position 0, standstill, SG min/max not available

Driver 8: position 0, standstill, SG min/max not available

Driver 9: position 0, standstill, SG min/max not available

Driver 10: position 0

Driver 11: position 0

Date/time: 2020-10-08 18:24:23

Cache data hit count 187762902

Slowest loop: 11.53ms; fastest: 0.17ms

I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0

=== Storage ===

Free file entries: 10

SD card 0 detected, interface speed: 20.0MBytes/sec

SD card longest read time 3.4ms, write time 13.9ms, max retries 0

=== Move ===

Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms

Bed compensation in use: mesh, comp offset 0.000

=== MainDDARing ===

Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1

=== AuxDDARing ===

Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1

=== Heat ===

Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1

=== GCodes ===

Segments left: 0

Movement lock held by null

HTTP is idle in state(s) 0

Telnet is idle in state(s) 0

File is idle in state(s) 0

USB is idle in state(s) 0

Aux is idle in state(s) 0

Trigger is idle in state(s) 0

Queue is idle in state(s) 0

LCD is idle in state(s) 0

Daemon is idle in state(s) 0

Autopause is idle in state(s) 0

Code queue is empty.

=== Network ===

Slowest loop: 50.53ms; fastest: 0.02ms

Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions

HTTP sessions: 1 of 8

Interface state active, link 100Mbps full duplex

=== DueX ===

Read count 1, 0.62 reads/min

    0

33
Posts
471
Views

OwenD

I can confirm same issue
Resets after any filament macro is run.
Duet 2 wifi

09/10/2020, 7:42:16 pm	M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2-beta2 running on Duet WiFi 1.02 or later
Board ID: 08DGM-917NK-F2MS4-7J1DA-3S86T-TZTWD
Used output buffers: 3 of 24 (16 max)
=== RTOS ===
Static ram: 24028
Dynamic ram: 100328 of which 44 recycled
Exception stack ram used: 264
Never used ram: 6408
Tasks: NETWORK(ready,154) HEAT(blocked,294) MAIN(running,415) IDLE(ready,19)
Owned mutexes:
=== Platform ===
Last reset 00:00:38 ago, cause: software
Last software reset at 2020-10-09 19:41, reason: AssertionFailed, GCodes spinning, available RAM 6112, slot 2
Software reset code 0x4123 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x20004264 Task MAIN
Stack: 0000059e 004716a8 00450849 0000003b ffffffff 20000c90 4d454144 200032a8 ffffffff 00000000 20002eb4 a5a5a5a5 004508cb 200042b0 0045e98c 20007940 0044e14f 200042cc 00446049 2000329c 200042cc 00000001 200042d4 00000000 004460b3 000000c8 200042d4
Error status: 0x00
MCU temperature: min 35.6, current 36.4, max 36.8
Supply voltage: min 24.2, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 0, standstill, SG min/max not available
Driver 1: position 0, standstill, SG min/max not available
Driver 2: position 0, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2020-10-09 19:42:16
Cache data hit count 62172132
Slowest loop: 140.85ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.5ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 40.15ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address bc:dd:c2:89:a0:bb
WiFi Vcc 3.38, reset reason Power up
WiFi flash size 4194304, free heap 23128
WiFi IP address 192.168.1.163
WiFi signal strength -58dBm, reconnections 0, sleep mode modem
Clock register ffffffff

dc42

Thanks, I have located the problem. Will be fixed in next beta, and I may have an unofficial build before then.

TC

@dc42 Thanks David. Fast as allways

dc42

@TC , if you would like to test the fix, there is a new binary for Duet 2 at https://www.dropbox.com/s/5vhjjz4a28hu33g/Duet2CombinedFirmware.bin?dl=0.

TC

@dc42 It works perfectly!

dc42

Thanks for the feedback.