2 Component Fans

Heartleander81 · 26 Oct 2020, 20:34

Unfortunately not. I can only control Fan2 via the slider in the DWC. With M106 S255, only fan 1 starts, not fan 1 and fan 2 together

Phaedrux · 26 Oct 2020, 20:40

In DWC there should be a tool fan slider that controls both.

Heartleander81 · 26 Oct 2020, 21:25

@Phaedrux

I only have one for Fan1 and one for Fan2, none for both

Phaedrux · 26 Oct 2020, 22:01

Can you post a screenshot of your DWC fan sliders?

Heartleander81 · 27 Oct 2020, 03:48

@Phaedrux

Heartleander81 · 27 Oct 2020, 20:24

@Phaedrux need you more from the DWC ore is that so ok?

Phaedrux · 27 Oct 2020, 20:28

Is that a screenshot from your phone? Can you connect to the DWC via a PC web browser?

Heartleander81 · 27 Oct 2020, 20:38

yes it was from my Phone. Now a screen from my Pc

Phaedrux · 27 Oct 2020, 20:42

If you click on "Allgemein" What version of Duet Web Control is shown?

If you look on the "status" page, you should see another fan control slider there that should have tool fan as well as the two part cooling fans. Tool fan should control both at the same time.

Heartleander81 · 27 Oct 2020, 20:51

i change the language to english, i think is better for you

Phaedrux · 27 Oct 2020, 20:53

Thanks.

In the status page on the right side you can see the fan sliders. The "change visibility" button lets you choose to show each slider for fan0 and fan1 as well as the "tool fan" slider which is the combined fans defined in M563.

Heartleander81 · 27 Oct 2020, 20:54

@Phaedrux there is no tool fan option only "Bauteil1" and "Bauteil2"

Phaedrux · 27 Oct 2020, 20:57

You don't see the tool fan option when clicking on "change visibility"

Heartleander81 · 27 Oct 2020, 21:00

there is not another option

Phaedrux · 27 Oct 2020, 21:05

You don't currently have a tool selected. Send T0 and look again.

Try adding T0 to the end of your config.g so that your first tool is selected at start up.

Heartleander81 · 27 Oct 2020, 21:08

@Phaedrux ok now i have Tool Fan control. Many many thanks now it is work.

I can start fan 1 und fan 2 with M106 S255

Phaedrux · 27 Oct 2020, 21:11

Send T0 as a command, or click on the name of your tool "Hotend" in the web interface.

That will select the tool and the tool fan defined for that tool will show up in the list of fan sliders.

Heartleander81 · 27 Oct 2020, 21:12

@Phaedrux it is work. Many many thanks.

Phaedrux · 27 Oct 2020, 21:14

You are welcome. Thanks for posting the photos of what you are seeing. It makes it a lot easier to understand what's going on.

Adding T0 to the end of config.g will ensure that a tool is always selected at startup. This would normally also be in the slicer start gcode. Without a tool selected, you can't print.

Heartleander81 · 27 Oct 2020, 21:18

@Phaedrux I have write T0 at custom settings are not defined and save the config.g.

I am so happy.