New Duet 2 extruder not working

GG

Im Still trying to send video, the paneldue even shows the current temps of bed and extruder so its obviously talking to the duet board but not reading the same config

Phaedrux

Yes I'm very curious to see what's actually going on.

GG

@Phaedrux Ive got the video on gmail google drive but cant figure how to attach it to this box

Phaedrux

There's a share menu in there some where that you can get a link to copy and paste here.

GG

@Phaedrux Cant see a share menu will have to try another system, should I try erasing paneldue and reinstalling firmware. ?

Phaedrux

If you click on the video icon in google drive there is a bar along the top of the window that has what looks like a stylized paper clip or chain link icon. If you hover over it, it says get link. Clicking on it will bring up a window that should give you a web URL to copy.

You can also right click on the movie file in google drive and in the menu there is a "get link" item as well.

Phaedrux

@GG said in New Duet 2 extruder not working:

should I try erasing paneldue and reinstalling firmware. ?

No, let's try and figure out where we are before we burn the map.

GG

@Phaedrux Yep got that far "get link" it says no one added yet, how do I put in this forum s link, sorry about my lack of savy

Phaedrux

Once you're in the Get Link pop up you should be able to just copy the link and paste it here.

alt text

GG

@GG https://drive.google.com/file/d/1ZpLHyBXsJ4Dwc_gfxwHcxilEoOrmHD_C/view?usp=sharing hope this works, if video not good enough I can make another

Phaedrux

Almost. You'll be getting an email requesting access to your link. Then I should be able to see it.

GG

@Phaedrux Havent recieved any email

Phaedrux

Maybe try getting a link again, but in the middle of the popup box make sure it says "anyone with a link" like it says in my screen shot.

GG

@Phaedrux https://drive.google.com/file/d/1ZpLHyBXsJ4Dwc_gfxwHcxilEoOrmHD_C/view?usp=sharing

Phaedrux

It works!! I will watch it tomorrow.

Veti

is it a mistake from copy and pasting, or does your homey contain both homey and homeall?

also your homing files are incorrect for corexy, they contain H2 for X and Y movement.

G1 H2 X5 Y5 F6000 ; go back a few mm

a correct homeall for example looks like this

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Nov 01 2020 07:53:14 GMT+0100 (Central European Standard Time)
G91                     ; relative positioning
G1 H2 Z5 F6000          ; lift Z relative to current position
G1 H1 X-235 Y-215 F1800 ; move quickly to X or Y endstop and stop there (first pass)
G1 H1 X-235             ; home X axis
G1 H1 Y-215             ; home Y axis
G1 X5 Y5 F6000          ; go back a few mm
G1 H1 X-235 F360        ; move slowly to X axis endstop once more (second pass)
G1 H1 Y-215             ; then move slowly to Y axis endstop
G90                     ; absolute positioning
G1 X15 Y15 F6000        ; go to first bed probe point and home Z
G30                     ; home Z by probing the bed

; Uncomment the following lines to lift Z after probing
;G91                    ; relative positioning
;G1 Z5 F100             ; lift Z relative to current position
;G90                    ; absolute positioning

i would suggest that you recreate your homing files in the configurator.

Phaedrux

It looks a little odd on the paneldue screen when you go to press the homing buttons. It looks like the homeall button gets touched instead of the homex.

On the paneldue can you get to the setup page and redo the touch calibration?

Fundamentally the Paneldue buttons can't do anything different than what the web control buttons do. They both use the same macros. But if the Paneldue touch calibration is out of whack you could be pressing the homeall button without realizing it, hence the unexpected results.

Another thing to try would be to go to the console page on the Paneldue and test if the keyboard works. Are you able to touch the keys or are they out of whack too?

Your video didn't show what happens when you press homeall on the web interface.

Also, as Veti says, you should remove the H2 from your homing files on the lines that move X and Y. The H2 can stay on the lines that raise and lower the Z axis.

GG

@Phaedrux You are on to something here, when I press homeall on web control, it behaves exactly as pressing homex on paneldue, ie, it move diagonally to the x end stop and shows x homed and thats it. I have no response at all from setup or console buttons on the paneldue so cant get at the page to even test keyboard or touch calibration. Should I replace H2 in xy homing config g with H1 or just remove it.

Phaedrux

Ok now we're getting some where. We will need to fix your homeall macro to work correctly and we will need to redo the touch calibration on the panel to make it useable.

In homeall you should remove the H2 on the G1 X and Y lines. Veti provided a good example of how it should look.

For the paneldue we may need to reflash the firmware but lemme check on that.

Phaedrux

Since we don't know what firmware version you have on your PanelDue at the moment and cant check because we can't get to the setup screen I think the best way forward is to simply erase the firmware and reflash it. After the firmware is reapplied the first thing it does is prompt you to calibrate the touch accuracy by poking a few black spots on the edges.

https://duet3d.dozuki.com/Wiki/PanelDue_Firmware_update

Do you happen to know what version of PanelDue you bought? I can tell from the video that it's not a 5i or 7i since the PCB is separate.