Reset during print Part 2 - Duet 3.1.1 / 3.2beta3 - Duet3+SBC

chrishamm

I've got more details about this problem, it looks like lxpanel (a program for the desktop running in the background) has a memory leak and which, at some point, causes problems with DSF. I hope this will be fixed by Raspbian soon.

@Via Please try out 3.2.0-b3.2 in standalone mode, the memory protection fault should be fixed in that build.

Via

@chrishamm Thanks for the update.

Would using the non-gui version of duetpi and forgoing connected screen work around this issue for the short term keeping SBC control?

Have updated standalone to 3.2.0-b3.2 and running test again now.

chrishamm

@Via Yes, I think so. My printer has the GUI-less variant installed (DuetPi lite), so that probably explains why I couldn't observe this problem before.

Via

@chrishamm No luck again on standalone with 3.2.0-beta3.2, this time "AssertionFailed"

I will have another try later with duetpi lite.

=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.2-beta3.2 running on Duet 3 MB6HC v0.6 or 1.0 (standalone mode)
Board ID: 08DJM-956L2-G43S4-6J9FA-3S86T-1B5LD
Used output buffers: 1 of 40 (11 max)
=== RTOS ===
Static ram: 122236
Dynamic ram: 168580 of which 376 recycled
Never used RAM 101000, free system stack 180 words
Tasks: NETWORK(ready,165) ETHERNET(blocked,109) HEAT(blocked,293) CanReceiv(blocked,948) CanSender(blocked,371) CanClock(blocked,358) TMC(blocked,54) MAIN(running,1111) IDLE(ready,19)
Owned mutexes:
=== Platform ===
Last reset 00:00:28 ago, cause: software
Last software reset at 2020-11-19 11:11, reason: AssertionFailed, GCodes spinning, available RAM 101000, slot 0
Software reset code 0x4123 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00427000 BFAR 0x00000000 SP 0x2040fd54 Task MAIN
Stack: 00000599 004886b0 00468ce5 00000000 ffffffff 20427700 2040e2a0 20427ab0 ffffffff 00000000 56a3ba63 a5a5a5a5 00468d9b 2040fda4 00000000 20423aa8 004664d5 20427aa0 00440cc3 00000000 20427aa4 20408001 2040fdb4 00000101 00469700 0046972e 61000000
Error status: 0x00
MCU temperature: min 37.1, current 37.8, max 38.0
Supply voltage: min 13.0, current 13.0, max 13.1, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
Driver 0: position 0, standstill, reads 9148, writes 14 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 9149, writes 14 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 9151, writes 14 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 9152, writes 14 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 9153, writes 14 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 9157, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2020-11-19 11:12:08
Slowest loop: 6.68ms; fastest: 0.21ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 1.2ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, StepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, StepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 11.39ms; fastest: 0.03ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 0 0 0
Socket states: 5 2 2 2 2 0 0 0
=== CAN ===
Messages sent 113, send timeouts 113, longest wait 0ms for type 0, free CAN buffers 47

dc42

@Via , I will look into this later today.

Via

@dc42 Many thanks.

Is it worth trying with DuetPi Lite? Was going to try earlier but work got in the way

dc42

@Via said in Reset during print Part 2 - Duet 3.1.1 / 3.2beta3 - Duet3+SBC:

@dc42 Many thanks.

Is it worth trying with DuetPi Lite? Was going to try earlier but work got in the way

I doubt it. The assertion failure looks like it was caused either by memory corruption, or possibly by a power brownout. I guess a hardware problem is also a possibility.

Can you set up a macro that runs the file in simulation mode within a loop, to see if you can provoke the failure that way?

Via

@dc42 I've ran the file as a normal simulation which completes fine.

Trying to do a macro to loop it but my gcode knowledge is terrible and keep freezing the board can you point me in right direction?

Was thinking this (I know never ending loops are bad in themselves but was just going to let it run until I reset it) but looks like it is just buffering all the M24s in one go how would I go about waiting for it to finish one before starting the next?

M37 S1
M23 "[PLA] CFFFP_Top - ReRender - zero temps.gcode"
while true
	M24

Via

@dc42 Stopped overthinking it and just added the M37/M23/M24 to the end of gcode which is looping properly now.

Has done ~130 loops with no issues in simulation.

Via

Simulation loop ran for 4 1/2 hours (~380 loops) with no issues.

Ripped 24V PSU out of another printer today and unplugged heaters and fans so just steppers and sensors plugged in and done another test print, again this did not complete.

This time M122 back to Memory Protection Fault

=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.2-beta3.2 running on Duet 3 MB6HC v0.6 or 1.0 (standalone mode)
Board ID: 08DJM-956L2-G43S4-6J9FA-3S86T-1B5LD
Used output buffers: 2 of 40 (11 max)
=== RTOS ===
Static ram: 122236
Dynamic ram: 168580 of which 376 recycled
Never used RAM 101000, free system stack 200 words
Tasks: NETWORK(ready,161) ETHERNET(blocked,109) HEAT(blocked,297) CanReceiv(blocked,948) CanSender(blocked,371) CanClock(blocked,356) TMC(blocked,54) MAIN(running,1111) IDLE(ready,19)
Owned mutexes:
=== Platform ===
Last reset 00:00:20 ago, cause: software
Last software reset at 2020-11-21 19:46, reason: MemoryProtectionFault mmarValid daccViol, Platform spinning, available RAM 101000, slot 1
Software reset code 0x4160 HFSR 0x00000000 CFSR 0x00000082 ICSR 0x00427804 BFAR 0x00038100 SP 0x2040aa78 Task TMC
Stack: 00000001 2040a928 00000000 00410210 00000000 00469d0f 00415682 21000000 427a0001 3c800001 00000000 3d000001 00000000 00000000 37533333 43d697a0 00000000 41dde946 43fa0000 44a80000 2040ff38 00469d0f 00000000 40078000 20400020 00415681 0000001e
Error status: 0x00
MCU temperature: min 39.2, current 39.9, max 40.0
Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
Driver 0: position 0, standstill, reads 35967, writes 14 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 35968, writes 14 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 35969, writes 14 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 35970, writes 14 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 35971, writes 14 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 35975, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2020-11-21 19:46:54
Slowest loop: 6.26ms; fastest: 0.15ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 0.8ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, StepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, StepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 5.46ms; fastest: 0.03ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 0 0 0
Socket states: 5 2 2 2 2 0 0 0
=== CAN ===
Messages sent 82, send timeouts 82, longest wait 0ms for type 0, free CAN buffers 46

dc42

@Via thanks, I will look into that data later.

dc42

@Via, please post the config.g file that you were using with 3.2beta3.2 when that assertion failure occurred.

Do you have any filament monitors configured? [Edit: from your M122 report i think that you do not.]

Via

@dc42 Thank you.

Config attached, not been changed from assertation failure (or from 3.1.1). No filament monitors.

config.g

Via

@dc42 any update on this?

dc42

I wasn't able to pin this down, except to say that it looks like random memory failure or corruption. Please upgrade to 3.4beta4. If it happens again, please post the print file and config.g if you haven't already (I'm using a tablet, so I can't tell), also daemon.g if you are using it.

Via

@dc42 Failed again on beta4 (M122 at bottom) they are posted already but will group together here.

config.g

[PLA] CFFFP_Top - ReRender - zero temps (1).gcode

full sys directory: https://www.viaraix.net/duet3-sys.zip

=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.2-beta4 running on Duet 3 MB6HC v0.6 or 1.0 (standalone mode)
Board ID: 08DJM-956L2-G43S4-6J9FA-3S86T-1B5LD
Used output buffers: 1 of 40 (11 max)
=== RTOS ===
Static ram: 123212
Dynamic ram: 168584 of which 704 recycled
Never used RAM 99692, free system stack 188 words
Tasks: NETWORK(ready,169) ETHERNET(blocked,110) HEAT(blocked,298) CanReceiv(blocked,947) CanSender(blocked,371) CanClock(blocked,358) TMC(blocked,54) MAIN(running,1113) IDLE(ready,19)
Owned mutexes:
=== Platform ===
Last reset 00:00:19 ago, cause: software
Last software reset at 2020-11-27 11:41, reason: MemoryProtectionFault mmarValid daccViol, GCodes spinning, available RAM 99692, slot 2
Software reset code 0x4163 HFSR 0x00000000 CFSR 0x00000082 ICSR 0x0044a804 BFAR 0x00000000 SP 0x204100c8 Task MAIN
Stack: 00000002 ffffffff 00434a29 20410308 000002bc 00469483 0046a3c8 610f0000 2042565c 004691bf 2042565c 00000000 000002bb 0000000a 2042565c 204256c8 00000000 00000001 00000000 00468e53 204256c8 00000000 204256c8 004691bf 00000000 00000000 20425540
Error status: 0x00
MCU temperature: min 39.0, current 39.4, max 39.9
Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.0, current 12.1, max 12.1, under voltage events: 0
Driver 0: position 0, standstill, reads 32774, writes 14 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 32775, writes 14 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 32776, writes 14 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 32777, writes 14 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 32779, writes 14 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 32782, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2020-11-27 11:41:21
Slowest loop: 6.06ms; fastest: 0.15ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 0.7ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 375, MinFreeDm: 375, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, StepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, StepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 17.56ms; fastest: 0.03ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 0 0 0
Socket states: 5 2 2 2 2 0 0 0
=== CAN ===
Messages queued 79, send timeouts 177, received 0, lost 0, longest wait 0ms for reply type 0, free buffers 47

dc42

Thanks for your new report. I am fairly certain that the memory protection fault was caused by a hardware error, because there is no way that the instruction at that address should fault, nor any way that the faulting address should be zero. So I suggest we swap your board. Who did you purchase it from?

Via

@dc42 thanks for your time looking into this. Purchase was from E3D but I have just gone over the 6 months now (purchased 13th May), will you be able to authorise warranty replacement as reported prior?

dc42

Yes I approve a warranty replacement.

Via

@dc42 Thank you, will get in touch with E3D. Many thanks for your help.