Newbie: New Install on Ender 5 Plus---Willing to PAY$$$
-
Temps are good. I used my infrared thermo.
-
Bear in mind you are running Firmware 3 where as I am not. But here is your gcode with the bolded sections changed. Feel free to try that.
Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.4 on Sun Nov 15 2020 03:22:47 GMT-0500 (Eastern Standard Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"E5Plus" ; set printer name; Network
M551 P"xxxxx" ; set password
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S0 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E130 ; set steps per mm
M566 X600 Y600 Z60.00 E3000.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z1200.00 E6000.00 ; set maximum speeds (mm/min)
M201 X1500.00 Y1500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M204 P600 T1500 ;set print and travel accellerations
M906 X800 Y800 Z800 E800 I50 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z***-1*** S1 ; set axis minima
M208 X350 Y350 Z400 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F60 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X16.3 Y14 Z2.43 ; set Z probe trigger value, offset and trigger height
M557 X15:190 Y15:190 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 A101.7 C607.1 D2.6 S1.00 V24.3 B0 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C
M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 A268.5 C102.1 D3.1 S1.00 V24.2 B0 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; 280 deg max on hot end; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue -
@RyanP said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
M906 X800 Y800 Z800 E800 I50 ; set motor currents (mA) and motor idle factor in per cent
Do you have your Z motors in series? Connected to both Z connectors?
-
No, they are separate with one being run off E1.
This allows me to run a G32 command to do a left to right adjustment during my bed compensation macro.
CR10S, August 2018
Anycubic Photon S December 2019
Ender 5 Feb 2020
Ender 5 Plus May 2020
Anycubic Photon Mono X Nov 2020
~
https://3dimensiongames.com/ -
@RyanP
Can you send me your filament files? -
From where, my slicer?
CR10S, August 2018
Anycubic Photon S December 2019
Ender 5 Feb 2020
Ender 5 Plus May 2020
Anycubic Photon Mono X Nov 2020
~
https://3dimensiongames.com/ -
@shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
Do i have to auto tune again?
no
-
@RyanP What are you using for a slicer? I thought they are universal across all slicers. Im using Creality's
-
2nd print at 200c. Little better. What should I do next? Drop it more? Im not going to be using PLA. I am just using the sample that came with the printer. I have black PETG. Should I put that in and continue from there?
-
that is already looking good. maybe a bit overextrusion or it could be bad quality filament.
try reducing the flow by 10%petg printing is a bit more difficult compared to pla. its not as forgiving.
-
I compared it to the first print and it actually looks alot better. The layers are more uniformed and color also. I think have it set at 135 for extrusion. I will drop it down to 130.
-
@shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
I think have it set at 135 for extrusion. I will drop it down to 130.
is that your esteps or percent of flow?
-
That is esteps
-
pla does not like to be overextruded, but underextrusion is ok.
so try 125 if 130 is the default for your extruder.
-
PETG @ 230 C. Its the best print yet!. There was a little sting inside the cabin. Thats it! Maybe drop it 5 deg?
-
If u see stuff on the side of the hull, thats cat hair. The cat loves going near the stupid printer
-
what happened to the chimney?
next thing to set up is pressure advance.
https://duet3d.dozuki.com/Wiki/Pressure_advance -
Thats a good question LOL. I dunno. I left it running while I was at work
-
@shatty said in Newbie: New Install on Ender 5 Plus---Willing to PAY$$:
Thats a good question LOL.
you cat got it?
you might want to get some plexiglas covers for the side so your cat does not get near it.
