Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    ToolBoard: 2 wires fan, heater fault and how to extrude ?

    Scheduled Pinned Locked Moved Unsolved
    Duet Hardware and wiring
    6
    112
    5.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Pseud3mysundefined
      Pseud3mys
      last edited by

      I mean invert A+ with B- and B+ with A- ?

      Vetiundefined 1 Reply Last reply Reply Quote 0
      • Vetiundefined
        Veti @Pseud3mys
        last edited by

        @Pseud3mys

        like turning the connector 180 degrees?
        yes that inverts the motor direction

        1 Reply Last reply Reply Quote 0
        • Pseud3mysundefined
          Pseud3mys
          last edited by

          yes, okay thank.

          1 Reply Last reply Reply Quote 0
          • Pseud3mysundefined
            Pseud3mys
            last edited by

            R25 (kΩ): 500 ± 3%
            β25/85 (K): 3800 ± 2%

            I find this for the thermistor.

            M308 S1 P"121.temp0" Y"thermistor" T500000 B3800
            

            so I put this, the temp is 12°c when it must be ~19 I think. I have always the fault, do you now what I nead to change ?

            Vetiundefined dc42undefined 2 Replies Last reply Reply Quote 0
            • Pseud3mysundefined
              Pseud3mys
              last edited by

              I send M302 P1 to allow cold extrusion, and I test if the command went good:
              "Cold extrusion is allowed (use M302 P0 to forbid it)"

              but I still can't use it:Capture.PNG

              1 Reply Last reply Reply Quote 0
              • Pseud3mysundefined
                Pseud3mys
                last edited by

                Capture.PNG
                I test the "extrudeur 2" here, see it heat 5°c and then it stop.

                1 Reply Last reply Reply Quote 0
                • Vetiundefined
                  Veti @Pseud3mys
                  last edited by

                  @Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                  R25 (kΩ): 500 ± 3%
                  β25/85 (K): 3800 ± 2%
                  I find this for the thermistor.

                  in the online configurator
                  https://configtool.reprapfirmware.org/Heaters
                  click on the beta field and in the popup select slice high temperature.

                  1 Reply Last reply Reply Quote 0
                  • Pseud3mysundefined
                    Pseud3mys @Veti
                    last edited by

                    @Veti said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                    @Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                    I connected the 2 wires fan on OUT2 (3 pins) and when I start it nothing happen (I have tested all wiring possible).

                    how did you configure it? post your config.g

                    ; Fans
                    M950 F0 C"121.out2" Q500                            ; create fan 0 on pin 121.out2 and set its frequency
                    M106 P0 S0 H-1                                      ; set fan 0 value. Thermostatic control is turned off
                    M950 F1 C"122.out2" Q500                            ; create fan 1 on pin 122.out2 and set its frequency
                    M106 P1 S0 H-1                                      ; set fan 1 value. Thermostatic control is turned off
                    

                    I put this, directly from RRF config tool.

                    1 Reply Last reply Reply Quote 0
                    • Vetiundefined
                      Veti
                      last edited by

                      did you verify that the fans are working? by connecting them to the always on port on the duet 3 mainboard?

                      Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                      • Pseud3mysundefined
                        Pseud3mys @Veti
                        last edited by

                        @Veti yes, On Vin and GND it work

                        Vetiundefined 1 Reply Last reply Reply Quote 0
                        • Vetiundefined
                          Veti @Pseud3mys
                          last edited by

                          @Pseud3mys

                          change the S0 to S1 for testing

                          Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                          • Pseud3mysundefined
                            Pseud3mys @Veti
                            last edited by

                            @Veti with S0 or S1 It work just when It is at 100% now. But not for all other value it don't work

                            Vetiundefined 1 Reply Last reply Reply Quote 0
                            • Vetiundefined
                              Veti @Pseud3mys
                              last edited by

                              @Pseud3mys
                              some fans do not work with pwm.

                              Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                              • Pseud3mysundefined
                                Pseud3mys @Veti
                                last edited by

                                @Veti I just see that is a 24v fan, I power the board with 12v. But if I power with 24v did the output will go up 24v as well ?

                                Vetiundefined 1 Reply Last reply Reply Quote 0
                                • Vetiundefined
                                  Veti @Pseud3mys
                                  last edited by

                                  @Pseud3mys said in ToolBoard: 2 wires fan, heater fault and how to extrude ?:

                                  I power the board with 12v. But if I power with 24v did the output will go up 24v as well ?

                                  no
                                  see the wiring diagram.

                                  https://duet3d.dozuki.com/Wiki/Duet_3_Tool_Board

                                  the out is 12v

                                  Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                                  • Pseud3mysundefined
                                    Pseud3mys
                                    last edited by

                                    ah yes, thank you

                                    1 Reply Last reply Reply Quote 0
                                    • Pseud3mysundefined
                                      Pseud3mys @Veti
                                      last edited by Pseud3mys

                                      @Veti have you an idea for the heater fault or the cold extrusion ?

                                      I send M302 P1 to allow cold extrusion, and I test if the command went good:
                                      "Cold extrusion is allowed (use M302 P0 to forbid it)"

                                      but I still can't use it:Capture.PNG

                                      1 Reply Last reply Reply Quote 0
                                      • Vetiundefined
                                        Veti
                                        last edited by

                                        what is the error message in the console?

                                        Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                                        • Pseud3mysundefined
                                          Pseud3mys @Veti
                                          last edited by Pseud3mys

                                          @Veti there are no error message. When I click on the "extrude" button nothing happen

                                          Vetiundefined 1 Reply Last reply Reply Quote 0
                                          • Vetiundefined
                                            Veti @Pseud3mys
                                            last edited by

                                            @Pseud3mys
                                            for the heating. how did you get the error?

                                            you still have not posted your config.g

                                            Pseud3mysundefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA