Duet2 WiFi Firmware on Raise 3d E2 ?

[Proschi3D]

@jay_s_uk On the motion board map.

The control board on the display has no card in it.

it boots from internal memory

[Proschi3D]

@jay_s_uk thanks, I'll test that at noon today

[Proschi3D]

here again the pictures of the two cards.
with a description of the connections

[jay_s_uk]

ah, that might be difficult then as the networking isn't handled by the control board and instead by the LCD screen.

[Veti]

can you post the output of m122?

[Proschi3D]

@Veti I do after work

[Proschi3D]

@jay_s_uk said in Duet2 WiFi Firmware on Raise 3d E2 ?:

ah, that might be difficult then as the networking isn't handled by the control board and instead by the LCD screen.

That's the problem

[dc42]

If the pins for the dedicated SPI channel are available on the main board, then you might be able to connect an ESP12-based WiFi module to the main board.

[Proschi3D]

@dc42 how can I find out ?

[Proschi3D]

again pictures of the motion board

[jay_s_uk]

you'll have to find out what pins are broken out to the main header.
Better get your multimeter out.
Or, contact raise3d and see if they'll give you a pinout

[A Former User]

As the board says based on the Duet2Wifi then I suppose they would have to comply with the open source license and provide the schematic (and layout files)?

[Proschi3D]

I just wrote to Raise and asked you for a pin assignment.

sorry my english comes from google translator;)

[A Former User]

Just refer to the CERN OHL 1.2 license for the Duet2Wifi if they don't give you what you want. (Or a link to this thread if they don't understand your request)

[Proschi3D]

thank you guys for your support and effort

[Proschi3D]

@Veti said in Duet2 WiFi Firmware on Raise 3d E2 ?:

can you post the output of m122?

(>>) === Diagnostics ===<LF>RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later<LF>Board ID: 08DLM-996RU-N8PS4-7J1D8-3SJ6N-1B9BR<LF>Used output buffers: 1 of 20 (1 max)<LF>=== RTOS ===<LF>Static ram: 25536<LF>Dynamic ram: 99000 of which 0 recycled<LF>Exception stack ram used: 256<LF>Never used ram: 6280<LF>Tasks: HEAT(blocked,1232) MAIN(running,3828) IDLE(ready,200)<LF>Owned mutexes:<LF>=== Platform ===<LF>Last reset 00:00:40 ago, cause: power up<LF>Last software reset time unknown, reason: User, spinning module GCodes, available RAM 6224 bytes (slot 0)<LF>Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d<LF>Error status: 0<LF>Free file entries: 10<LF>SD card 0 detected, interface speed: 20.0MBytes/sec<LF>SD card longest block write time: 0.0ms, max retries 0<LF>MCU temperature: min 18.7, current 23.2, max 23.4<LF>Supply voltage: min 0.0, current 0.6, max 0.9, under voltage events: 0, over voltage events: 0, power good: no<LF>Driver 0: ok, SG[Warning: Maximal number of bytes per line exceeded! Check the EOL (end-of-line) settings or increase the limit in the advanced terminal settings.]

[Veti]

so it seems to be running rrf2. not sure if they modified it.

if you want to risk it, you can update the firmware with rrf3

see
https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware
Fallback procedure #2

[Proschi3D]

@Veti this was not a good idea.
the printer does not start anymore

[jay_s_uk]

This should get you back up and running
https://drive.google.com/file/d/1X7L8mZ71x0eZNYgMeaI8VubTBc1Uk9uV/view?usp=sharing
i have built it from the raise3d sources

[Proschi3D]

(>>) Error: M997: In-application programming binary "Duet2CombinedIAP.bin" not found<LF>ok<LF>Error: M997: In-application programming binary "Duet2CombinedIAP.bin" not found<LF>ok<LF>