Duet2 WiFi Firmware on Raise 3d E2 ?

jay_s_uk

@Proschi78 so replace the contents of the www folder with the latest version of DWC from here. https://github.com/Duet3D/DuetWebControl/releases/tag/3.1.1
I suggest taking a backup of the sd card before you make any modifications

Proschi3D

@jay_s_uk On the motion board map.

The control board on the display has no card in it.

it boots from internal memory

Proschi3D

@jay_s_uk thanks, I'll test that at noon today

Proschi3D

here again the pictures of the two cards.
with a description of the connections Controler 2.jpg

jay_s_uk

ah, that might be difficult then as the networking isn't handled by the control board and instead by the LCD screen.

Veti

can you post the output of m122?

Proschi3D

@Veti I do after work

Proschi3D

@jay_s_uk said in Duet2 WiFi Firmware on Raise 3d E2 ?:

ah, that might be difficult then as the networking isn't handled by the control board and instead by the LCD screen.

That's the problem

dc42

If the pins for the dedicated SPI channel are available on the main board, then you might be able to connect an ESP12-based WiFi module to the main board.

Proschi3D

@dc42 how can I find out ?

Proschi3D

again pictures of the motion board

jay_s_uk

you'll have to find out what pins are broken out to the main header.
Better get your multimeter out.
Or, contact raise3d and see if they'll give you a pinout

A Former User

As the board says based on the Duet2Wifi then I suppose they would have to comply with the open source license and provide the schematic (and layout files)?

Proschi3D

I just wrote to Raise and asked you for a pin assignment.

sorry my english comes from google translator;)

A Former User

Just refer to the CERN OHL 1.2 license for the Duet2Wifi if they don't give you what you want. (Or a link to this thread if they don't understand your request)

Proschi3D

thank you guys for your support and effort

Proschi3D

@Veti said in Duet2 WiFi Firmware on Raise 3d E2 ?:

can you post the output of m122?

(>>) === Diagnostics ===<LF>RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later<LF>Board ID: 08DLM-996RU-N8PS4-7J1D8-3SJ6N-1B9BR<LF>Used output buffers: 1 of 20 (1 max)<LF>=== RTOS ===<LF>Static ram: 25536<LF>Dynamic ram: 99000 of which 0 recycled<LF>Exception stack ram used: 256<LF>Never used ram: 6280<LF>Tasks: HEAT(blocked,1232) MAIN(running,3828) IDLE(ready,200)<LF>Owned mutexes:<LF>=== Platform ===<LF>Last reset 00:00:40 ago, cause: power up<LF>Last software reset time unknown, reason: User, spinning module GCodes, available RAM 6224 bytes (slot 0)<LF>Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d<LF>Error status: 0<LF>Free file entries: 10<LF>SD card 0 detected, interface speed: 20.0MBytes/sec<LF>SD card longest block write time: 0.0ms, max retries 0<LF>MCU temperature: min 18.7, current 23.2, max 23.4<LF>Supply voltage: min 0.0, current 0.6, max 0.9, under voltage events: 0, over voltage events: 0, power good: no<LF>Driver 0: ok, SG[Warning: Maximal number of bytes per line exceeded! Check the EOL (end-of-line) settings or increase the limit in the advanced terminal settings.]

Veti

so it seems to be running rrf2. not sure if they modified it.

if you want to risk it, you can update the firmware with rrf3

see
https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware
Fallback procedure #2

Proschi3D

@Veti this was not a good idea.
the printer does not start anymore

jay_s_uk

This should get you back up and running
https://drive.google.com/file/d/1X7L8mZ71x0eZNYgMeaI8VubTBc1Uk9uV/view?usp=sharing
i have built it from the raise3d sources