Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    problem attuning bed heater

    Scheduled Pinned Locked Moved
    Config Tool
    5
    14
    506
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • konte1978undefined
      konte1978
      last edited by

      M303 autotuning procedure for bed heater never ends.
      failing to calibrate it automatically every time I start heating the bed I get this error.

      Error: Heater 0 fault: temperature rising much more slowly than the expected 1.6°C/sec

      ; Heaters
      ;Piatto riscaldato
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4138
      M950 H0 C"bedheat" T0
      M307 H0 B1 S1.00
      M140 H0
      M143 H0 S110

      Stephen6309undefined 1 Reply Last reply Reply Quote 0
      • Bennyundefined
        Benny
        last edited by

        make sure you have m501 in config, and m500 after autotune

        1 Reply Last reply Reply Quote 0
        • Stephen6309undefined
          Stephen6309 @konte1978
          last edited by

          @konte1978 Make sure you have the correct B value in M308.

          konte1978undefined 1 Reply Last reply Reply Quote 0
          • konte1978undefined
            konte1978
            last edited by

            ; Configuration file for Duet WiFi (firmware version 3)
            ; executed by the firmware on start-up
            ;
            ; generated by RepRapFirmware Configuration Tool v3.1.4 on Fri Jul 17 2020 20:24:58 GMT+0200 (CEST)

            ; General preferences
            G90 ; send absolute coordinates...
            M83 ; ...but relative extruder moves
            M550 P" CUBE PRO TRIO" ; set printer name

            ; Network
            M552 S1 ; enable network
            M586 P0 S1 ; enable HTTP
            M586 P1 S0 ; disable FTP
            M586 P2 S0 ; disable Telnet

            ; Drives
            M569 P0 S1 ; physical drive 0 goes forwards
            M569 P1 S1 ; physical drive 1 goes forwards
            M569 P2 S1 ; physical drive 2 goes forwards
            M569 P3 S1 ; physical drive 3 goes forwards
            M569 P4 S1 ; physical drive 4 goes forwards
            M569 P9 S1 ; physical drive 9 goes forwards
            M584 X0 Y1 Z2 E3:4:9 ; set drive mapping
            M350 X16 Y16 Z16 E16:16:16 I1 ; configure microstepping with interpolation
            M92 X87.35 Y87.43 Z1076.77 E82.09:82.09:82.09 ; set steps per mm
            M566 X900.00 Y900.00 Z12.00 E120.00:120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
            M203 X15000.00 Y15000.00 Z1200.00 E600.00:600.00:600.00 ; set maximum speeds (mm/min)
            M201 X500.00 Y500.00 Z250.00 E250.00:250.00:250.00 ; set accelerations (mm/s^2)
            M906 X1500 Y1500 Z800 E1200:1200:1200 I30 ; set motor currents (mA) and motor idle factor in per cent (ho modficato la corrente dei motori dell'estrusore da 800 a 1200)
            M84 S30 ; Set idle timeout

            ; Axis Limits
            M208 X0 Y0 Z0 S1 ; Imposta valore minimo deli assi
            M208 X290 Y295.3 Z205 ; imposta il valore massimo degli assi ho tolto il valore S0 ALLA FINE DELLA RIGA

            ; Endstops
            M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
            M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
            M574 Z1 S1 P"zstop" ; configure active-high endstop for low end on Z via pin zstop

            ; Z-Probe
            M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
            M950 S0 C"duex.pwm5" ; creare il servo pin 0 per BLTouch
            M558 P9 C"^zprobe.in" H5 F120 T6000 A10 R0.75 S0.02 ; set Z probe type to bltouch and the dive height + speeds
            G31 P25 X-11.70 Y-51.2 Z2.75 ; impostare il valore del trigger della sonda Z, l'offset e l'altezza del trigger
            M557 X12.3:290 Y24.80:295 S20 ; define mesh grid

            ; Heaters
            ;Piatto riscaldato
            ;M570 H0 P90 T20 ; sto cercando di far aspettare fino che il piatto si riscaldi prima che mi dia errore
            M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
            M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
            M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
            M140 H0 ; map heated bed to heater 0
            M143 H0 S110 ; set temperature limit for heater 0 to 120C
            ;Estrusore numero 1
            M308 S1 P"spi.cs1" Y"rtd-max31865" ; configure sensor 1 as thermistor on pin e0temp
            M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
            M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
            M143 H1 S290; set temperature limit for heater 0 to 120C
            ;Estrusore numero 2
            M308 S2 P"spi.cs2" Y"rtd-max31865" ; configure sensor 2 as thermistor on pin e1temp
            M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
            M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
            M143 H2 S270
            ;Estrusore numero 3
            M308 S3 P"spi.cs3" Y"rtd-max31865" ; M308 S3 P"duex.e2temp" Y"thermistor" T100000 B4725 ; configure sensor 3 as thermistor on pin duex.e2temp
            M950 H3 C"duex.e2heat" T3 ; create nozzle heater output on duex.e2heat and map it to sensor 3
            M143 H3 S270 ; set temperature limit for heater 0 to 120C
            M307 H3 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
            ; Riscaldatore della camera
            M141 H4 ; il riscaldatore 4 è il riscaldatore della camera
            M950 H4 C"duex.e3heat" T4 ; configura l'uscita per il riscaldamento della camera sull pin e della scheda duex
            M308 S4 P"duex.e3temp" Y"thermistor" T100000 B5500 C7.06Ee-8 ; configure sensor 4 as thermistor on pin duex.e2temp
            M143 H4 S70 ; set temperature limit for heater 0 to 120C
            M301 H4 B1 ; utilizzare il controllo bang-bang per il riscaldatore della camera

            ; Fans
            M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
            M106 P0 C"ESTRUSORI" S0 H3:2:1 T120 ; set fan 0 name and value. Thermostatic control is turned on
            M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
            M106 P1 C"NOZZLE" S0 H1:2:3 T45 ; set fan 1 name and value. Thermostatic control is turned on
            M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
            M106 P2 C"LUCI LED" S0 H-1 ; set fan 2 name and value. Thermostatic control is turned off
            M950 F3 C"duex.fan6" Q500 ; create fan 3 on pin duex.fan6 and set its frequency
            M106 P3 C"VENTOLA 6" S0 H-1 ; set fan 3 name and value. Thermostatic control is turned off
            M950 F4 C"duex.fan7" Q500 ; create fan 4 on pin duex.fan7 and set its frequency
            M106 P4 C"VENTOLA 7" S0 H-1 ; set fan 4 name and value. Thermostatic control is turned off

            ; Tools
            M563 P0 S"estrusore 1" D0 H1 F0:1 ; define tool 0
            G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
            G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
            M563 P1 S"estrusore 2" D1 H2 F0:1 ; define tool 1
            G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
            G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C
            M563 P2 S"estrusore 3" D2 H3 F0:1 ; define tool 2
            G10 P2 X0 Y0 Z0 ; set tool 2 axis offsets
            G10 P2 R0 S0 ; set initial tool 2 active and standby temperatures to 0C

            ; Sensori di folamento degli estrusori se imposto l'ultima S0 disabilita il confronto tra filamento aspetatto e quello realmente estruso,S1 abilita il controllo
            M591 D0 P5 C"e0stop" R5:190 E3.0 S0 ; ho configurato il filamento del primo estrusore sull'uscita e0stop valori sensibilità filamneto originale R40:120
            M591 D1 P5 C"connlcd.encb" R5:190 E3.0 S1 ; ho configurato il filamento del secondo estrusore sull'uscita stop10(ECN_B) valori sensibilità filamneto originale R40:120
            M591 D2 P5 C"e1stop" R5:190 E3.0 S1 ; ho configurato il filamento del terzo estrusore sull'uscita e1stop valori sensibilità filamneto originale R40:120

            ; Custom settings are not defined
            M575 P1 S1 B57600 ;per abilitare lcd paneldue
            M501

            1 Reply Last reply Reply Quote 0
            • konte1978undefined
              konte1978 @Stephen6309
              last edited by

              @Stephen6309 i don't know the B value in M308, how can i get it?

              1 Reply Last reply Reply Quote 0
              • Vetiundefined
                Veti
                last edited by

                it should be in your thermistor documentation

                konte1978undefined 1 Reply Last reply Reply Quote 0
                • konte1978undefined
                  konte1978 @Veti
                  last edited by

                  @Veti said in problem attuning bed heater:

                  t should be in your thermistor documentation

                  unfortunately I have no documentation, I made the mistake of getting it on amazon

                  https://www.amazon.it/dp/B07RJHYRP5/ref=cm_sw_r_wa_api_fabc_hm15Fb6K3JJWZ?_encoding=UTF8&psc=1

                  Stephen6309undefined 1 Reply Last reply Reply Quote 0
                  • Stephen6309undefined
                    Stephen6309 @konte1978
                    last edited by

                    @konte1978 Write to the seller and ask for the beta value.

                    1 Reply Last reply Reply Quote 0
                    • Vetiundefined
                      Veti
                      last edited by

                      most likely they used the very common B3950 thermistor

                      1 Reply Last reply Reply Quote 0
                      • konte1978undefined
                        konte1978
                        last edited by

                        Screenshot at Dec 26 16-44-54.png
                        I entered the b-value of B3950 and launched the calibration. Nothing changes, I do not know if it is the fault of the 8mm plate that I used for the printing pact. increase of the test.

                        1 Reply Last reply Reply Quote 0
                        • konte1978undefined
                          konte1978
                          last edited by

                          661be1ac-2759-4947-acc9-4c18745623bf.jpg

                          1 Reply Last reply Reply Quote 0
                          • Phaedruxundefined
                            Phaedrux Moderator
                            last edited by

                            What firmware version are you using?
                            Your screen shot shows the tuning process is running.
                            Does it ever finish? How long are you waiting?
                            Does it ever throw an error message?
                            When it's complete you need to send M500 to save the results.

                            Z-Bot CoreXY Build | Thingiverse Profile

                            konte1978undefined 1 Reply Last reply Reply Quote 0
                            • konte1978undefined
                              konte1978 @Phaedrux
                              last edited by

                              @Phaedrux Hi I'm using RepRapFirmware for Duet 2 WiFi / Ethernet version 3.2-RC2.
                              the test goes on even for 30 minutes without giving any error

                              1 Reply Last reply Reply Quote 0
                              • Phaedruxundefined
                                Phaedrux Moderator
                                last edited by Phaedrux

                                The new heater tuning algorithm in 3.2 can take a long time. Just let it finish.

                                https://forum.duet3d.com/topic/19761/new-heater-tuning-algorithm

                                Z-Bot CoreXY Build | Thingiverse Profile

                                1 Reply Last reply Reply Quote 0
                                • First post
                                  Last post
                                Unless otherwise noted, all forum content is licensed under CC-BY-SA