can't connect to DWC via different devices.
-
when i try to connect to the DWC i get a connection time out error. this is on my laptop and smartphone. i can connect to it via my main pc (wired connection) and via the laptop op my parents. what could be the problem?
i didn't had this problem in the beginning with my laptop. i did had it with my phone.diagnostics of my duet 2 wifi
=== Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2 running on Duet WiFi 1.02 or later Board ID: 08DLM-996RU-N85T0-6J9FG-3S86Q-KBSRN Used output buffers: 3 of 24 (22 max) === RTOS === Static ram: 23460 Dynamic ram: 73476 of which 76 recycled Never used RAM 15068, free system stack 103 words Tasks: NETWORK(ready,169) HEAT(blocked,309) MAIN(running,456) IDLE(ready,19) Owned mutexes: WiFi(NETWORK) === Platform === Last reset 01:25:47 ago, cause: software Last software reset details not available Error status: 0x00 Aux0 errors 0,0,0 MCU temperature: min 25.2, current 28.8, max 29.4 Supply voltage: min 23.6, current 23.8, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: position 21268, ok, SG min/max 0/250 Driver 1: position -934, standstill, SG min/max 0/1023 Driver 2: position 440, ok, SG min/max 0/1023 Driver 3: position 0, ok, SG min/max 0/190 Driver 4: position 0, standstill, SG min/max not available Driver 5: position 0 Driver 6: position 0 Driver 7: position 0 Driver 8: position 0 Driver 9: position 0 Driver 10: position 0 Driver 11: position 0 Date/time: 2021-01-08 11:48:25 Cache data hit count 4294967295 Slowest loop: 71.98ms; fastest: 0.20ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Storage === Free file entries: 9 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest read time 4.2ms, write time 1.0ms, max retries 0 === Move === DMs created 83, maxWait 3660008ms, bed compensation in use: mesh, comp offset 0.000 === MainDDARing === Scheduled moves 2783, completed moves 2780, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state 3 === AuxDDARing === Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 Heater 0 is on, I-accum = 0.5 Heater 1 is on, I-accum = 0.6 === GCodes === Segments left: 1 Movement lock held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is doing "G1 X182.915 Y196.174 E529.0788" in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 201.44ms; fastest: 0.10ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions HTTP sessions: 2 of 8 - WiFi - Network state is active WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 1 WiFi firmware version 1.25 WiFi MAC address ec:fa:bc:5b:3c:72 WiFi Vcc 3.38, reset reason Turned on by main processor WiFi flash size 4194304, free heap 27000 WiFi IP address 192.168.1.244 WiFi signal strength -58dBm, mode 802.11n, reconnections 0, sleep mode modem Clock register 00002002 Socket states: 0 0 0 0 0 0 0 0i had this problem with 3.1.1 and also with 3.2 (just updated to this).
-
Does your router isolate wired and wireless devices?
-
This post is deleted! -
@Phaedrux as far as i know not, except for devices that are connected to wireless connection for quests but my laptop or 3d printer isn't connected to this. i have a netgear Nighthawk X4S. maybe there is something i overlooked in the settings that you can say that can cause the problem? when i try to ping the 3d printer from the devices that can't connect i get connection timed out. from the other devices i get a reply. i also could connect to it via a other laptop that is connected via wifi.
-
Are you able to ping the IP?
-
@Phaedrux via the pc that can get to DWC yes, via devices that can't connect to DWC not
-
Then you've definitely got a network isolation problem.
Are the ips even in the same subnet?
-
@Phaedrux yes, all devices are in the same subnet. i also have a raspberry pi and i can connect to that from all devices in my network. i can also do remote desktop to my other pc that can connect to the 3d printer.
-
i have removed the printer from the network and reconnected it. it looks like it is working now. i wil look if it stays working the comming days and let it know if it still works.
-
I wonder if the router tried to shunt the Duetwifi over to the 5Ghz network?
-
@Phaedrux in my router i have this option disabled, so i don't think this caused the problem.
also i haven't had any problems since i reconnected the printer with the network, thanks for your help.
-
@robh345 same issue for me..
All devices on the same network. I can connect to DWC with iPad, iPhone, and until recently my laptop. Now, the raspberry pi connected to the Duet3 doesn't respond to pings from my laptop, but it does from other devices.
-
@dbruce-ae05 Best to start a new thread.
