macro executing if wanted after print ?

A Former User

You might consider giving this a vote "up" if it would likely fit your needs:
https://forum.duet3d.com/topic/20708/start-g-end-g?_=1610541552963

DIY-O-Sphere

@joeko said in macro executing if wanted after print ?:

for example after the fan is off shut down with M81.

You don't need a macro for that
Put "M81 S1" in the slicer end code......

fcwilt

@DIY-O-Sphere said in macro executing if wanted after print ?:

@joeko said in macro executing if wanted after print ?:

for example after the fan is off shut down with M81.

You don't need a macro for that
Put "M81 S1" in the slicer end code......

Will that wait for the fan to stop running before it shuts off power?

Frederick

A Former User

@joeko

Or - In your case you might make a screen-message-request with M291 within stop.g that is called via "M0 command at the end of the print job"?

Veti

@fcwilt said in macro executing if wanted after print ?:

Will that wait for the fan to stop running before it shuts off power?

yes

Sn n=0 turn power off immediately (default), n=1 turn power off when all thermostatic fans have turned off (RepRapFirmware 1.20 and later only)

joeko

i use also a printer with repetier server.
in repetier server there is a button and when i click on this button while a print is running a command will execute after the print is finished and this command is m81 s1 or what i set in this command.
i can set rules what happen after a print.

when i set m81 s1 in the slicer this will run after every print but i would like do this only if i want.

Phaedrux

https://duet3d.dozuki.com/Wiki/Duet_Web_Control_v2_and_v3_(DWC)_Manual#Section_Job_Control

Enable auto-sleep may be what you want?

The print control section has a check box to "Enable Auto-Sleep". If this is selected then the M1 G-Code is sent at the end of the print which runs the "sleep.g" macro file. This for example would allow the shutting down of the main power supply once the print has completed (assuming the printer hardware is set up to allow this).

joeko

@Phaedrux said in macro executing if wanted after print ?:

https://duet3d.dozuki.com/Wiki/Duet_Web_Control_v2_and_v3_(DWC)_Manual#Section_Job_Control

Enable auto-sleep may be what you want?

The print control section has a check box to "Enable Auto-Sleep". If this is selected then the M1 G-Code is sent at the end of the print which runs the "sleep.g" macro file. This for example would allow the shutting down of the main power supply once the print has completed (assuming the printer hardware is set up to allow this).

yes it seems that is what i am looking for
perfect and thank you

joeko

hmm,
doesnt work.
do i have to open the browser ? after closeing the browser and open again the auto-sleep is disable again.

appjaws

I have a macro for auto shutdown which you could call from an entry in the end section of your slicer:-
M98 P"0:/macros/extra/Auto Shutdown

this is my macro:-
"M291 P"Shutdown Started" R"Shutdown" S1 T0; Display message

M98 P"0:/macros/extra/Set LED Red"
M140 S0 ; turn off bed heater
M104 S0 ; turn off extruder heater

if move.axes[0].homed || move.axes[1].homed || move.axes[3].homed || move.axes[4].homed
G91 ; relative mode
G1 Z5 F2000 ; move bed down 5mm
G90 ; absolute mode
G1 Y228 V228 X118 U118 F3000 ; Park position
else M291 P"ERROR - Drives not homed, Please shutdown manually" R"Shutdown" S1 T0; Display message
break

while heat.heaters[1].current > 42
M98 P"0:/macros/extra/Set LED Green"
M291 P{"Waiting for nozzle to reduce to 42C, Extruder temperature = " ^ floor(heat.heaters[1].current + 0.5)}
M106 P0 S255 ;set cooling fan to maximum
G4 S5 ;Wait for 5 second

M106 P0 S0 ;set cooling fan to zero
M106 P3 S0
M106 P4 S0
M106 P5 S0
M291 P"Shutdown Completed" R"Shutdown"; Display message

you could put everything you need to happen in this macro but keep the section
while heat.heaters[1].current > 42

Hope that helps

Phaedrux

@joeko said in macro executing if wanted after print ?:

hmm,
doesnt work.
do i have to open the browser ? after closeing the browser and open again the auto-sleep is disable again.

It may very well be one of the few features that depends on DWC being open. Another I can think of is the fan speed override lock.

joeko

ok, maybe a option in future firmware