IMPORTANT ISSUE with bed temp controller

Luke'sLaboratory · 14 Jan 2021, 17:10

@jay_s_uk Agreed, this makes me anxious

jay_s_uk · 14 Jan 2021, 17:10

@Veti said in IMPORTANT ISSUE with bed temp controller:

i would suggest that you connect it to out0

doesn't really matter in this case as its using an external relay

Luke'sLaboratory · 14 Jan 2021, 17:11

@Veti Depending on the actual thermistors they could be, but having all 3 be identical is suspect for sure! - would need validation to be 100% sure. For relay outputs, any output is fine, I prefer to use a connectorized output for my SSR ones.

Veti · 14 Jan 2021, 17:11

@Luke-sLaboratory

B4138 thermistors have not been used in years. so its very unlikely that its correct.

Luke'sLaboratory · 14 Jan 2021, 17:12

@Veti Fair, I have some in a cabinet somewhere as a backup to my backup's backups.

jrockland · 14 Jan 2021, 17:15

@jay_s_uk Jan 14 00:00:09 raspberrypi rsyslogd: [origin software="rsyslogd" swVersion="8.1901.0" x-pid="388" x-info="https://www.rsyslog.com"] rsyslogd was HUPed
Jan 14 00:00:10 raspberrypi systemd[1]: man-db.service: Succeeded.
Jan 14 00:00:10 raspberrypi systemd[1]: Started Daily man-db regeneration.
Jan 14 00:02:30 raspberrypi DuetControlServer[14574]: [warn] Lost connection to Duet (Board is not available (no header))
Jan 14 00:02:30 raspberrypi DuetControlServer[14574]: [info] Connection to Duet established
Jan 14 00:04:45 raspberrypi rngd[377]: stats: bits received from HRNG source: 480064
Jan 14 00:04:45 raspberrypi rngd[377]: stats: bits sent to kernel pool: 424096
Jan 14 00:04:45 raspberrypi rngd[377]: stats: entropy added to kernel pool: 424096
Jan 14 00:04:45 raspberrypi rngd[377]: stats: FIPS 140-2 successes: 24
Jan 14 00:04:45 raspberrypi rngd[377]: stats: FIPS 140-2 failures: 0
Jan 14 00:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Monobit: 0
Jan 14 00:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Poker: 0
Jan 14 00:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Runs: 0
Jan 14 00:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Long run: 0
Jan 14 00:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Continuous run: 0
Jan 14 00:04:45 raspberrypi rngd[377]: stats: HRNG source speed: (min=238.614; avg=440.907; max=492.430)Kibits/s
Jan 14 00:04:45 raspberrypi rngd[377]: stats: FIPS tests speed: (min=3.285; avg=14.301; max=31.423)Mibits/s
Jan 14 00:04:45 raspberrypi rngd[377]: stats: Lowest ready-buffers level: 2
Jan 14 00:04:45 raspberrypi rngd[377]: stats: Entropy starvations: 0
Jan 14 00:04:45 raspberrypi rngd[377]: stats: Time spent starving for entropy: (min=0; avg=0.000; max=0)us
Jan 14 00:17:01 raspberrypi CRON[32185]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly)
Jan 14 00:25:30 raspberrypi DuetControlServer[14574]: [warn] Lost connection to Duet (Board is not available (no header))
Jan 14 00:25:30 raspberrypi DuetControlServer[14574]: [info] Connection to Duet established
Jan 14 00:32:49 raspberrypi DuetControlServer[14574]: [warn] Lost connection to Duet (Board is not available (no header))
Jan 14 00:32:49 raspberrypi DuetControlServer[14574]: [info] Connection to Duet established
Jan 14 00:51:21 raspberrypi DuetControlServer[14574]: [warn] Bad header CRC32 (expected 0x6d61620f, got 0x45d967fb)
Jan 14 00:51:21 raspberrypi DuetControlServer[14574]: [warn] Note: RepRapFirmware didn't receive valid data either (code 0x00000005)
Jan 14 00:56:55 raspberrypi DuetControlServer[14574]: [warn] Bad header CRC32 (expected 0xd5e94b60, got 0x4319b529)
Jan 14 00:56:55 raspberrypi DuetControlServer[14574]: [warn] Note: RepRapFirmware didn't receive valid data either (code 0x00000005)
Jan 14 01:04:29 raspberrypi DuetControlServer[14574]: [warn] Lost connection to Duet (Board is not available (no header))
Jan 14 01:04:29 raspberrypi DuetControlServer[14574]: [info] Connection to Duet established
Jan 14 01:04:45 raspberrypi rngd[377]: stats: bits received from HRNG source: 500064
Jan 14 01:04:45 raspberrypi rngd[377]: stats: bits sent to kernel pool: 454336
Jan 14 01:04:45 raspberrypi rngd[377]: stats: entropy added to kernel pool: 454336
Jan 14 01:04:45 raspberrypi rngd[377]: stats: FIPS 140-2 successes: 25
Jan 14 01:04:45 raspberrypi rngd[377]: stats: FIPS 140-2 failures: 0
Jan 14 01:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Monobit: 0
Jan 14 01:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Poker: 0
Jan 14 01:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Runs: 0
Jan 14 01:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Long run: 0
Jan 14 01:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Continuous run: 0
Jan 14 01:04:45 raspberrypi rngd[377]: stats: HRNG source speed: (min=238.614; avg=440.930; max=492.430)Kibits/s
Jan 14 01:04:45 raspberrypi rngd[377]: stats: FIPS tests speed: (min=3.285; avg=14.314; max=31.423)Mibits/s
Jan 14 01:04:45 raspberrypi rngd[377]: stats: Lowest ready-buffers level: 2
Jan 14 01:04:45 raspberrypi rngd[377]: stats: Entropy starvations: 0
Jan 14 01:04:45 raspberrypi rngd[377]: stats: Time spent starving for entropy: (min=0; avg=0.000; max=0)us
Jan 14 01:17:01 raspberrypi CRON[3031]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly)
Jan 14 01:30:42 raspberrypi DuetControlServer[14574]: [error] Heater 1 fault: temperature excursion exceeded 15.0°C (target 90.0°C, actual 128.2°C)
Jan 14 01:30:42 raspberrypi DuetControlServer[14574]: [info] Job has been paused at byte 8469316, reason HeaterFault
Jan 14 01:30:42 raspberrypi DuetControlServer[14574]: [info] Starting macro file pause.g on channel Autopause
Jan 14 01:30:42 raspberrypi DuetControlServer[14574]: [info] Finished macro file pause.g
Jan 14 01:30:46 raspberrypi DuetControlServer[14574]: [info] Printing paused at X182.6 Y50.4 Z40.6 U10.0 V10.0
Jan 14 01:40:42 raspberrypi DuetControlServer[14574]: [info] Cancelled printing file 0:/gcodes/MEGATOR P1.gcode, print time was 8h 15m
Jan 14 01:40:42 raspberrypi DuetControlServer[14574]: [error] Shutting down due to un-cleared heater fault after 600 seconds
Jan 14 01:59:09 raspberrypi systemd[1]: Starting Daily apt download activities...
Jan 14 01:59:11 raspberrypi systemd[1]: apt-daily.service: Succeeded.
Jan 14 01:59:11 raspberrypi systemd[1]: Started Daily apt download activities.
Jan 14 02:04:45 raspberrypi rngd[377]: stats: bits received from HRNG source: 540064
Jan 14 02:04:45 raspberrypi rngd[377]: stats: bits sent to kernel pool: 484096
Jan 14 02:04:45 raspberrypi rngd[377]: stats: entropy added to kernel pool: 484096
Jan 14 02:04:45 raspberrypi rngd[377]: stats: FIPS 140-2 successes: 27
Jan 14 02:04:45 raspberrypi rngd[377]: stats: FIPS 140-2 failures: 0
Jan 14 02:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Monobit: 0
Jan 14 02:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Poker: 0
Jan 14 02:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Runs: 0
Jan 14 02:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Long run: 0
Jan 14 02:04:45 raspberrypi rngd[377]: stats: FIPS 140-2(2001-10-10) Continuous run: 0
Jan 14 02:04:45 raspberrypi rngd[377]: stats: HRNG source speed: (min=238.614; avg=443.777; max=492.430)Kibits/s
Jan 14 02:04:45 raspberrypi rngd[377]: stats: FIPS tests speed: (min=3.285; avg=14.223; max=31.423)Mibits/s
Jan 14 02:04:45 raspberrypi rngd[377]: stats: Lowest ready-buffers level: 2
Jan 14 02:04:45 raspberrypi rngd[377]: stats: Entropy starvations: 0
Jan 14 02:04:45 raspberrypi rngd[377]: stats: Time spent starving for entropy: (min=0; avg=0.000; max=0)us

Veti · 14 Jan 2021, 17:17

@jrockland said in IMPORTANT ISSUE with bed temp controller:

Jan 14 01:30:42 raspberrypi DuetControlServer[14574]: [error] Heater 1 fault: temperature excursion exceeded 15.0°C (target 90.0°C, actual 128.2°C)

this suggest a failure of the relay

Luke'sLaboratory · 14 Jan 2021, 17:17

@jrockland said in IMPORTANT ISSUE with bed temp controller:

pberrypi rngd[377]: stats: bits sent to kernel pool: 484096
Jan 14 02:04:45 raspb

My take from this is that it shut down the duet after 10 min of heater fault, and if the relays need a high signal to turn off, by having no signal (from a shut down duet) it just stayed on and caused the issue.

jrockland · 14 Jan 2021, 17:17

@Veti didnt understand the first part but Ill change it to out.0

Veti · 14 Jan 2021, 17:18

@jrockland said in IMPORTANT ISSUE with bed temp controller:

didnt understand the first part

it means your bed will be reporting the wrong temperature.
it will display 100C but it wont be 100C

jrockland · 14 Jan 2021, 17:20

@Luke-sLaboratory I dont know what SSR mean, but they look like normal relays to me.

Veti · 14 Jan 2021, 17:22

@jrockland said in IMPORTANT ISSUE with bed temp controller:

SSR

Solid State Relay.
Using cheap ones is a sure way to burn your house down.

Luke'sLaboratory · 14 Jan 2021, 17:24

@jrockland https://duet3d.dozuki.com/Wiki/Connecting_thermistors_or_PT1000_temperature_sensors - Relevant documentation.

I'd take a serious look at what relays you are using (whether they're SSR's or traditional) the correct switching frequency, which thermistors you actually have in all of your machines, and the configuration of using a high Signal from the duet to turn relays off.

Preferably you'd drop the frequency to ~10hz (by adding a Q10 to your M950 where you set up the output for out3 (or out1)), and reconfigure/aquire new relays that require a high signal from the duet to turn on. That way, if your duet goes offline for whatever reason, your relays will not turn on.

Next I'd definitely recommend high-quality SSRs. Cheap/underrated/undercooled ones will latch on and have the exact behavior that may have caused this issue in the first place. Thats why I was looking for specifics on the relays used.

jrockland · 14 Jan 2021, 17:25

@Luke-sLaboratory the board send a ON signal as soon as I power it up if I remove the "!".. Ill need the tech to look into that asap. seem like it working the wrong way.

Luke'sLaboratory · 14 Jan 2021, 17:26

@jrockland Do you mean that your relay turns on if you take off the ! from the duet config? or is the duet's output turning on when you remove the !

jrockland · 14 Jan 2021, 17:28

@Luke-sLaboratory not the ssr's, im testing the board with a meter right now. relays had been tested and work good.

jrockland · 14 Jan 2021, 17:29

@Veti yea I looked at the picture and it is what we use.

Veti · 14 Jan 2021, 17:34

@jrockland said in IMPORTANT ISSUE with bed temp controller:

yea I looked at the picture and it is what we use.

what picture?

jrockland · 14 Jan 2021, 17:37

@Luke-sLaboratory the relay turn off as soon as they are not fed power

jrockland · 14 Jan 2021, 17:37

@Veti looked online for ssr relays