Duet2 WiFi Firmware on Raise 3d E2 ?

[Phaedrux]

@Proschi78 said in Duet2 WiFi Firmware on Raise 3d E2 ?:

What should I enter?

M350 X16 Y16 Z16 E16:16 I1

Make sure your steps per mm in M92 is correct for x16.

[Proschi3D]

M350 X256 Y256 Z256 E256:256 I0

This is how it is entered in the original Raise 3D config

[Phaedrux]

Don't do that, it will overload the CPU. Use x16 and interpolation instead.

[Proschi3D]

Perhaps that was the problem of pausing in printing with the original firmware?

[Veti]

@Proschi78 said in Duet2 WiFi Firmware on Raise 3d E2 ?:

Perhaps that was the problem of pausing in printing with the original firmware?

very likely

[Proschi3D]

Can I calculate the steps?

[Veti]

@Proschi78 said in Duet2 WiFi Firmware on Raise 3d E2 ?:

Can I calculate the steps?

https://blog.prusaprinters.org/calculator_3416/

[Proschi3D]

M92 X1280.00 Y1280.00 Z4000.00 E420.00:420.00 ; set steps per mm @256

M92 X1280=1280/4=320 ? @16

[Veti]

256 / 16 = 16
1280 / 16 = 80

[Proschi3D]

Now I have one more problem. When I go z home the printer moves to the upper limit switch and the pin of the Z probe remains extended

[Phaedrux]

Post your homeall.g

Also, you don't have any steps per mm or microstepping set for the U axis.

M92 X1280.00 Y1280.00 Z4000.00 E420.00:420.00 ; set steps per mm

[Proschi3D]

@Phaedrux It works now, many thanks for your help. Now I just have to get the Idex to work properly. Single extruder and dual function, only the mirtor mode and duplicate mode not yet

[Proschi3D]

As expected, the Idex setup did not work;)

Here are my settings

; Configuration file for Duet WiFi (firmware version 2.00)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.2 on Mon Jan 25 2021 18:31:38 GMT+0100 (Mitteleuropäische Normalzeit)
M575 P1 S1 B57600
M552 S1
; General preferences
G90                                               ; send absolute coordinates...
M83                                               ; ...but relative extruder moves
M550 P"My Printer"                                ; set printer name
 
; Network
 
; Drives
M569 P0 S0
M569 P1 S1
M569 P2 S0
M569 P3 S1
M569 P4 S1
M569 P5 S0                                        ; physical drive 4 goes forwards
M584 X0 Y1 Z2 E3:4 U5                              ; set drive mapping
M350 X128 Y128 U128 Z128 E128:128 I1                 ; configure microstepping without interpolation
M92 X640 Y640 U640 Z6400 E2150:2150     ; set steps per mm
M566 X480 Y300 U480 Z24 E300:300                  ; set maximum instantaneous speed changes (mm/min)
M203 X9000 U9000 Y9000 Z720 E3000:3000            ; set maximum speeds (mm/min)
M201 X1000 U1000 Y500 Z100 E3000:3000       ; set accelerations (mm/s^2)
M906 X900 U900 Y900 Z900 E800:800 I30                ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                           ; Set idle timeout
 
; Axis Limits
M204 P800 T1500
M208 X-3 Y0 Z0 U35 S1                                  ; set axis minima
M208 X327 Y240 Z240 U355 S0                            ; set axis maxima
 
; Endstops
M574 X1 Y1 U2 S1
M574 Z2 S1                                  ; set active high endstops
 
; Z-Probe
M558 X100 P5 H7 F100 T9000 R2 I1                             ; set Z probe type to unmodulated and the dive height + speeds
G31 P2 X15 Y18 Z0.515                               ; set Z probe trigger value, offset and trigger height
M557 X15:335 Y18:245 S80:50                          ; define mesh grid
 
; Heaters
M305 P0 T100000 B3950 C0 R4700                       ; set thermistor + ADC parameters for heater 0
M143 H0 S120                                      ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C200433 R4700          ; set thermistor + ADC parameters for heater 1
M143 H1 S320                                      ; set temperature limit for heater 1 to 320C
M305 P2 T100000 B4725 C200433 R4700          ; set thermistor + ADC parameters for heater 2
M143 H2 S320                                      ; set temperature limit for heater 2 to 320C
 
; Fans
M106 P0 S0 I0 F500 H-1                            ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F500 H-1                            ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P2 S0 I0 F500 H-1                            ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off
 
; Tools
M563 P0 D0 H1                         ; define tool 0
G10 P0 X0 Y0 Z0                                   ; set tool 0 axis offsets
G10 P0 R0 S0                                      ; set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H2 X3                        ; define tool 1
G10 P1 U0 Y0 Z0                             ; set tool 1 axis offsets
G10 P1 R0 S0                                      ; set initial tool 1 active and standby temperatures to 0C
M563 P2 D0:1 H1:2 X0:3
M567 P2 E1.0:1.0
G10 P2 X0 U0 Y0 Z0
G10 P2 R0 S0
M591 D0 C6 P1 S1
M591 D1 C7 P1 S1
 
;Idex Setup
M563 P0 D0 H1               S"X" ; define tool X
M563 P1 D1 H2     X3    F2    S"U" ; define tool U
M563 P2 D0:1 H1:2 X0:3  F0:2  S"XU" ; define tool X+U copy mode
G10 P2 X50 Y0 U-50 S0 R0 ; set tool offsets and temperatures
M567 P2 E1:1 ; set mix ratio 100% on both extruders
 
 
 
M555 P6
M501
T0
; Custom settings are not defined

[Veti]

@Proschi78 said in Duet2 WiFi Firmware on Raise 3d E2 ?:

M305 P1 T100000 B4725 C200433 R4700 ; set thermistor + ADC parameters for heater 1
M305 P2 T100000 B4725 C200433 R4700 ; set thermistor + ADC parameters for heater 2

you still have not fixed your thermistor setting C200433 is incorrect

[Proschi3D]

@Veti But it only works with these settings

[Veti]

what thermistor do you have?

[Proschi3D]

@Veti https://www.3djake.de/slice-engineering/mosquito-heizpatrone

[Proschi3D]

[Veti]

@Proschi78
thats not whats in the picture. can you post a link to the thermistors data sheet?

[Proschi3D]

thermocouple max31855