duet3d sd not detected, rejects http, com5 denied
-
@Phaedrux I have a ender 3 pro but I put a dual z motor on it. is there anything special i need to set up on the config?
I also have a upgraded heated-bed and use a 500c Nova hotend.
it came with a daughter board RTD 100 but im not sure how to hook it up. or what options to select in the config. -
Dual Z motors can either be used with the existing dual connector on the board with no special config needed, or if you want to use two separate drivers for each Z motor for lead screw leveling you can do that too, but will need to be added manually. See here: https://duet3d.dozuki.com/Wiki/Bed_levelling_using_multiple_independent_Z_motors
@radcad said in duet3d sd not detected, rejects http, com5 denied:
500c Nova hotend.
it came with a daughter board RTD 100I'm not sure what that is. Do you have any documentation for it? Or a link to it? Photo?
-
This is the hotend 500 C capable and claims to be unclogging
https://3dpassion.com/novaI currently have the second Z plugged into the second port. I don't need any special z movements.
This is the daughter board for the hotend that is 500c
https://duet3d.dozuki.com/Wiki/Connecting_PT100_temperature_sensors -
Then you don't need to do anything special for the Z axis. Just treat it as a single motor z axis.
For the PT100 you can choose the PT100 sensor in the config tool. (bottom of the sensor dropdown list)
-
the guy the makes the hot end said i need to but the safety shutoff for the hotend up 2 degrees how do i do that? I dont see a option for pt100.
-
@radcad said in duet3d sd not detected, rejects http, com5 denied:
I dont see a option for pt100.
Where are you looking?
Screen Shot 2021-01-31 at 10.16.12 PM.png@radcad said in duet3d sd not detected, rejects http, com5 denied:
the guy the makes the hot end said i need to but the safety shutoff for the hotend up 2 degrees how do i do that?
I'm not sure what you're saying.
-
@Phaedrux oh ok, now im not sure which to pick.
-
Which port on the daughter board are you using? RTD1 or RTD2? Those coincide with SPI.CS1 and SPI.CS2 in the drop down.
-
@Phaedrux
im not sure i havent wired it up yet -
Well those are your two options. RTD1 would be the most logical.
https://duet3d.dozuki.com/Wiki/Connecting_PT100_temperature_sensors
https://duet3d.dozuki.com/Wiki/PT100_temperature_sensor_daughter_board -
@Phaedrux this one ?
-
Look in the i/o mapping page.
Did you select firmware version 3.0+ at the start? You are on 3.2 now right?
-
it does not five me a option for that
-
@Phaedrux said in duet3d sd not detected, rejects http, com5 denied:
Did you select firmware version 3.0+ at the start? You are on 3.2 now right?
-
@Phaedrux I installed all the file you gave me. the config im still unsure on some options to choose.
-
@radcad Can you be more specific?
-
@Phaedrux
If this is what you mean, then yes.
sorry im a newb at all thius thank you for helping me out with this.
-
@radcad said in duet3d sd not detected, rejects http, com5 denied:
the config im still unsure on some options to choose.
Yes, but I mean what options are you unsure of?
-
@Phaedrux
If I use the ender 3 pro preset. there is no expansion board config, but it allows me to add a dual stepper motor driver ?
for the bed control do I select PID or bang bang. i have a upgraded bed that runs on mains.
this part about which sensor location to read.
i think the first 2 spi spots are for 1 daughter board and 3 - 4 are for a second board but Im not sure.
-
Yes the highlighted option is for the first PT100 port on the daughterboard.
