Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Heigh error after calibrating

    Scheduled Pinned Locked Moved
    General Discussion
    probe firmware
    5
    59
    2.8k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • fcwiltundefined
      fcwilt @TristanKoeln
      last edited by fcwilt

      @TristanKoeln said in Heigh error after calibrating:

      @fcwilt with the G92 Z(dive heigh+triger high)
      is still the same problem

      After you performed the calibration routine you posted did you go back and update the G31 command with the correct Z trigger height as reported by the G30 S-1?

      Frederick

      Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

      1 Reply Last reply Reply Quote 0
      • TristanKoelnundefined
        TristanKoeln
        last edited by

        @fcwilt jup its 3.760

        fcwiltundefined 1 Reply Last reply Reply Quote 0
        • fcwiltundefined
          fcwilt @TristanKoeln
          last edited by

          @TristanKoeln said in Heigh error after calibrating:

          @fcwilt with the G92 Z(dive heigh+triger high)
          is still the same problem

          Since the G30 leaves Z at dive height + trigger height setting it again to the same value with G92 is redundant.

          It doesn't hurt but isn't needed.

          Frederick

          Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

          1 Reply Last reply Reply Quote 0
          • fcwiltundefined
            fcwilt @TristanKoeln
            last edited by

            @TristanKoeln said in Heigh error after calibrating:

            @fcwilt jup its 3.760

            Are you still running the "PLA" macro?

            If so what does it look like.

            Frederick

            Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

            1 Reply Last reply Reply Quote 0
            • TristanKoelnundefined
              TristanKoeln
              last edited by

              @fcwilt

              G31 X-31.7 Y3,16 Z3,760 P25
              M291 P"PLA Offset" S0 T5
              
              fcwiltundefined 1 Reply Last reply Reply Quote 0
              • fcwiltundefined
                fcwilt @TristanKoeln
                last edited by

                @TristanKoeln said in Heigh error after calibrating:

                @fcwilt

                G31 X-31.7 Y3,16 Z3,760 P25
                M291 P"PLA Offset" S0 T5
                

                And that is the height reported by your calibration routine?

                Frederick

                Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                1 Reply Last reply Reply Quote 0
                • TristanKoelnundefined
                  TristanKoeln
                  last edited by

                  @fcwilt ya

                  1 Reply Last reply Reply Quote 0
                  • fcwiltundefined
                    fcwilt
                    last edited by

                    Hi,

                    Recall that before creating a height map with G29 S0 or before loading the height map with G29 S1 you need to position the probe to the center of the bed and do a single G30 to set the Z=0 datum.

                    Having set the Z trigger height to the value as reported by your calibration routine did you go back and re-create the height map using the new value?

                    Are you also setting the Z=0 datum when loading the new height map?

                    I mentioned that changing the Z trigger height to accommodate different filaments was not a good approach - one reason being is that it will mess up setting the Z=0 datum which may cause the height map to not work right.

                    Frederick

                    Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                    1 Reply Last reply Reply Quote 0
                    • TristanKoelnundefined
                      TristanKoeln
                      last edited by

                      @fcwilt i reprobed everything still same problem, could it be something with the zmin stop and the prob are on 2 diff heights? if yes what would be the solution

                      1 Reply Last reply Reply Quote 0
                      • fcwiltundefined
                        fcwilt
                        last edited by

                        Hi,

                        I've re-posted your files using the </> tag - it saves everyone the trouble of downloading your files.

                        Would you look at them and verify they are your current files?

                        Thanks.

                        Frederick

                        ; Configuration file for Duet WiFi (firmware version 3)
                        ; executed by the firmware on start-up
                        ;
                        ; generated by RepRapFirmware Configuration Tool v3.2.1 on Mon Jan 18 2021 17:44:49 GMT+0100 (Mitteleuropäische Normalzeit)
                        
                        ; General preferences
                        G90                                                 ; send absolute coordinates...
                        M83                                                 ; ...but relative extruder moves
                        M550 P"BIGCREATOR"                                  ; set printer name
                        
                        
                        ; Network
                        M552 S1                                             ;Tun Network ON
                                                    
                        ; Drives
                        M569 P0 S0                                          ; physical drive 0 goes forwards
                        M569 P1 S1                                          ; physical drive 1 goes forwards
                        M569 P2 S1                                          ; physical drive 2 goes forwards
                        M569 P3 S0                                          ; physical drive 3 goes forwards
                        M569 P4 S1                                          ; physical drive 4 goes forwards
                        M584 X0 Y1 Z2:4 E3                                  ; set drive mapping
                        M350 X16 Y16 Z16:16 E16 I1                          ; configure microstepping with interpolation
                        M92 X80.00 Y100.00 Z405:405.00 E750.00              ; set steps per mm
                        M566 X1800.00 Y1800.00 Z120.00:120.00 E500.00       ; set maximum instantaneous speed changes (mm/min)
                        M203 X36000.00 Y36000.00 Z200.00:200.00 E500.00     ; set maximum speeds (mm/min)
                        M201 X1000.00 Y1000.00 Z400.00:400.00 E500.00       ; set accelerations (mm/s^2)
                        M906 X1200 Y1200 Z1000:1000 E1000 I30               ; set motor currents (mA) and motor idle factor in per cent
                        M84 S30                                             ; Set idle timeout
                        
                        ; Axis Limits
                        M208 X0 Y0 Z-10 S1                                  ; set axis minima
                        M208 X440 Y440 Z400 S0                              ; set axis maxima
                        
                        ; Endstops
                        M574 X1 S1 P"xstop"                                 ; configure active-high endstop for low end on X via pin xstop
                        M574 Y1 S1 P"ystop"                                 ; configure active-high endstop for low end on Y via pin ystop
                        M574 Z1 S1 P"!zstop+!e1stop"                        ; configure active-high endstop for low end on Z via pin zstop
                        
                        ; Z-Probe
                        M558 P9 C"^zprobe.in" H5 F120 T5000                 ; BLTouch connected to Z probe IN pin
                        M950 S0 C"exp.heater3"                              ; create servo/gpio 0 on heater 3 pin on expansion connector
                        M98 P"/macros/NORMAL_Offset"                        ; set z probe offsets
                        
                        M280 P0 S10                                         ; send control signal to BLTouch through servo/gpio 0                                        
                                                                  
                        ;G31 P500 X0 Y0 Z25                                 ; set Z probe trigger value, offset and trigger height
                        M557 X10:390 Y10:390 S38:38                         ; define mesh grid
                        
                        ; Heaters
                        M308 S0 P"bedtemp" Y"thermistor" T100000 B4092      ; configure sensor 0 as thermistor on pin bedtemp
                        M950 H0 C"bedheat" T0                               ; create bed heater output on bedheat and map it to sensor 0
                        M307 H0 B0 S1.00                                    ; disable bang-bang mode for the bed heater and set PWM limit
                        M140 H0                                             ; map heated bed to heater 0
                        M143 H0 S120                                        ; set temperature limit for heater 0 to 120C
                        M308 S1 P"e1temp" Y"thermistor" T100000 B4092       ; configure sensor 1 as PT1000 on pin e0temp
                        M950 H1 C"e0heat" T1                                ; create nozzle heater output on e0heat and map it to sensor 1
                        M307 H1 B0 S1.00                                    ; disable bang-bang mode for heater  and set PWM limit
                        M143 H1 S280                                        ; set temperature limit for heater 1 to 280C
                        
                        ; Fans
                        M950 F0 C"fan0" Q0                                  ; create fan 0 on pin fan0 and set its frequency
                        ;M106 P0 S1 H-1                                      ; set fan 0 value. Thermostatic control is turned off
                        M950 F1 C"fan1" Q0                                  ; create fan 1 on pin fan1 and set its frequency
                        ;M106 P1 S1 H-1                                      ; set fan 1 value. Thermostatic control is turned off
                        M950 F2 C"fan2" Q0                                  ; create fan 2 on pin fan2 and set its frequency
                        ;M106 P2 S1 H-1                                      ; set fan 2 value. Thermostatic control is turned off
                        
                        ; Tools
                        M563 P0 S"WaterColledHead" D0 H1 F-1                ; define tool 0
                        G10 P0 X0 Y0 Z0                                     ; set tool 0 axis offsets
                        G10 P0 R0 S0                                        ; set initial tool 0 active and standby temperatures to 0C
                        
                        ; Custom settings are not defined
                        
                        ; Miscellaneous
                        M575 P1 S1 B57600                                   ; enable support for PanelDue
                        M501                                                ; load saved parameters from non-volatile memory
                        M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"  ; set voltage thresholds and actions to run on power loss
                        
                        G28                                                 ; home
                        
                        ; bed.g
                        ; called to perform automatic bed compensation via G32
                        ;
                        ; generated by RepRapFirmware Configuration Tool v3.2.1 on Mon Jan 18 2021 17:44:49 GMT+0100 (Mitteleuropäische Normalzeit)
                        M561     ; clear any bed transform
                        G28      ;home
                        G29 S1   ; probe the bed and enable compensation
                        M280 P0 S90 ; retractProbe
                        
                        ; homez.g
                        ; called to home the Z axis
                        ;
                        ; generated by RepRapFirmware Configuration Tool v3.2.1 on Mon Jan 18 2021 17:44:49 GMT+0100 (Mitteleuropäische Normalzeit)
                        G91               ; relative positioning
                        G1 H2 Z10 F6000   ; lift Z relative to current position
                        G1 H1 Z-500 F3000 ;Go down till endstop
                        G1 H2 Z10 F6000
                        G1 X200 Y200 F4000 ;go to midle
                        G30 ; move Z down until the endstop is triggered
                        G92 Z0         ; set Z position to axis minimum (you may want to adjust this)
                        
                        
                        
                        ; Uncomment the following lines to lift Z after probing
                        ;G91              ; relative positioning
                        ;G1 Z10 F100      ; lift Z relative to current position
                        G90              ; absolute positioning
                        
                        ; homeall.g
                        ; called to home all axes
                        ;
                        ; generated by RepRapFirmware Configuration Tool v3.2.1 on Mon Jan 18 2021 17:44:49 GMT+0100 (Mitteleuropäische Normalzeit)
                        
                        ;DUAL Z 
                        M584 Z2:4   
                        
                        M280 P0 S90
                        G91                     ; relative positioning
                        G1 H2 Z10 F6000         ; lift Z relative to current position
                        G1 H1 X-405 Y-405 F5000 ; move quickly to X and Y axis endstops and stop there (first pass)
                        G1 H2 X5 Y5 F6000       ; go back a few mm
                        G1 H1 X-405 Y-405 F360  ; move slowly to X and Y axis endstops once more (second pass)
                        M98 Phomez.g            ; move Z down stopping at the endstop
                        G90                     ; absolute positioning
                        G92 Z10                 ; set Z position to axis minimum (you may want to adjust this)
                        
                        ; Uncomment the following lines to lift Z after probing
                        ;G91                    ; relative positioning
                        ;G1 Z10 F100            ; lift Z relative to current position
                        ;G90                    ; absolute positioning
                        
                        
                        

                        Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                        TristanKoelnundefined 1 Reply Last reply Reply Quote 0
                        • Stephen6309undefined
                          Stephen6309 @fcwilt
                          last edited by

                          @fcwilt I adjust the Z offset so I don't have to remember to do baby steps on every print. Currently I only change the filament when I run out on the spool.

                          fcwiltundefined 1 Reply Last reply Reply Quote 0
                          • fcwiltundefined
                            fcwilt @Stephen6309
                            last edited by

                            @Stephen6309 said in Heigh error after calibrating:

                            @fcwilt I adjust the Z offset so I don't have to remember to do baby steps on every print. Currently I only change the filament when I run out on the spool.

                            As I said changing the Z trigger height may cause the height map to not work correctly.

                            And as I said you can use the filament management feature of DWC to allow you to select different filament types and make any adjustments desired to things like extruder temp, extrusion multiplier, baby step settings and more.

                            You don't have to do it for every print - it will happen automatically if your "print start" code invokes the the command needed to trigger the changes specified by the current filament.

                            Here is an example of a filament configuration file. Every filament type you enter into the DWC filament management feature will have it's own configuration file.

                            M221 S100 D0    ; set extrusion multiplier
                            G10 S200 R0	; set extruder temps
                            M140 S60 R0	; set bed temps
                            

                            Here are the commands you would place into your "print start" code that will invoke the configuration file for the currently selected filament type.

                            T0		; select tool 0 so extruder commands below will work
                            M703		; configure selected filament
                            

                            So once you select a filament type it will remain selected and every print will run the commands you have entered into the configuration file for that filament type.

                            Frederick

                            Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                            Stephen6309undefined 1 Reply Last reply Reply Quote 0
                            • Stephen6309undefined
                              Stephen6309 @fcwilt
                              last edited by

                              @fcwilt In my slicer's start gcode, I call the macros, then home, then G32 which does a G29 S1 or S0 depending on if it finds heightmap.csv. Never had a problem with the heightmap working correctly.

                              1 Reply Last reply Reply Quote 0
                              • TristanKoelnundefined
                                TristanKoeln @fcwilt
                                last edited by

                                @fcwilt

                                @fcwilt said in Heigh error after calibrating:

                                Hi,

                                I've re-posted your files using the </> tag - it saves everyone the trouble of downloading your files.

                                Would you look at them and verify they are your current files?

                                Thanks.

                                Frederick

                                ; Configuration file for Duet WiFi (firmware version 3)
                                ; executed by the firmware on start-up
                                ;
                                ; generated by RepRapFirmware Configuration Tool v3.2.1 on Mon Jan 18 2021 17:44:49 GMT+0100 (Mitteleuropäische Normalzeit)
                                
                                ; General preferences
                                G90                                                 ; send absolute coordinates...
                                M83                                                 ; ...but relative extruder moves
                                M550 P"BIGCREATOR"                                  ; set printer name
                                
                                
                                ; Network
                                M552 S1                                             ;Tun Network ON
                                                            
                                ; Drives
                                M569 P0 S0                                          ; physical drive 0 goes forwards
                                M569 P1 S1                                          ; physical drive 1 goes forwards
                                M569 P2 S1                                          ; physical drive 2 goes forwards
                                M569 P3 S0                                          ; physical drive 3 goes forwards
                                M569 P4 S1                                          ; physical drive 4 goes forwards
                                M584 X0 Y1 Z2:4 E3                                  ; set drive mapping
                                M350 X16 Y16 Z16:16 E16 I1                          ; configure microstepping with interpolation
                                M92 X80.00 Y100.00 Z405:405.00 E750.00              ; set steps per mm
                                M566 X1800.00 Y1800.00 Z120.00:120.00 E500.00       ; set maximum instantaneous speed changes (mm/min)
                                M203 X36000.00 Y36000.00 Z200.00:200.00 E500.00     ; set maximum speeds (mm/min)
                                M201 X1000.00 Y1000.00 Z400.00:400.00 E500.00       ; set accelerations (mm/s^2)
                                M906 X1200 Y1200 Z1000:1000 E1000 I30               ; set motor currents (mA) and motor idle factor in per cent
                                M84 S30                                             ; Set idle timeout
                                
                                ; Axis Limits
                                M208 X0 Y0 Z-10 S1                                  ; set axis minima
                                M208 X440 Y440 Z400 S0                              ; set axis maxima
                                
                                ; Endstops
                                M574 X1 S1 P"xstop"                                 ; configure active-high endstop for low end on X via pin xstop
                                M574 Y1 S1 P"ystop"                                 ; configure active-high endstop for low end on Y via pin ystop
                                M574 Z1 S1 P"!zstop+!e1stop"                        ; configure active-high endstop for low end on Z via pin zstop
                                
                                ; Z-Probe
                                M558 P9 C"^zprobe.in" H5 F120 T5000                 ; BLTouch connected to Z probe IN pin
                                M950 S0 C"exp.heater3"                              ; create servo/gpio 0 on heater 3 pin on expansion connector
                                M98 P"/macros/NORMAL_Offset"                        ; set z probe offsets
                                
                                M280 P0 S10                                         ; send control signal to BLTouch through servo/gpio 0                                        
                                                                          
                                ;G31 P500 X0 Y0 Z25                                 ; set Z probe trigger value, offset and trigger height
                                M557 X10:390 Y10:390 S38:38                         ; define mesh grid
                                
                                ; Heaters
                                M308 S0 P"bedtemp" Y"thermistor" T100000 B4092      ; configure sensor 0 as thermistor on pin bedtemp
                                M950 H0 C"bedheat" T0                               ; create bed heater output on bedheat and map it to sensor 0
                                M307 H0 B0 S1.00                                    ; disable bang-bang mode for the bed heater and set PWM limit
                                M140 H0                                             ; map heated bed to heater 0
                                M143 H0 S120                                        ; set temperature limit for heater 0 to 120C
                                M308 S1 P"e1temp" Y"thermistor" T100000 B4092       ; configure sensor 1 as PT1000 on pin e0temp
                                M950 H1 C"e0heat" T1                                ; create nozzle heater output on e0heat and map it to sensor 1
                                M307 H1 B0 S1.00                                    ; disable bang-bang mode for heater  and set PWM limit
                                M143 H1 S280                                        ; set temperature limit for heater 1 to 280C
                                
                                ; Fans
                                M950 F0 C"fan0" Q0                                  ; create fan 0 on pin fan0 and set its frequency
                                ;M106 P0 S1 H-1                                      ; set fan 0 value. Thermostatic control is turned off
                                M950 F1 C"fan1" Q0                                  ; create fan 1 on pin fan1 and set its frequency
                                ;M106 P1 S1 H-1                                      ; set fan 1 value. Thermostatic control is turned off
                                M950 F2 C"fan2" Q0                                  ; create fan 2 on pin fan2 and set its frequency
                                ;M106 P2 S1 H-1                                      ; set fan 2 value. Thermostatic control is turned off
                                
                                ; Tools
                                M563 P0 S"WaterColledHead" D0 H1 F-1                ; define tool 0
                                G10 P0 X0 Y0 Z0                                     ; set tool 0 axis offsets
                                G10 P0 R0 S0                                        ; set initial tool 0 active and standby temperatures to 0C
                                
                                ; Custom settings are not defined
                                
                                ; Miscellaneous
                                M575 P1 S1 B57600                                   ; enable support for PanelDue
                                M501                                                ; load saved parameters from non-volatile memory
                                M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"  ; set voltage thresholds and actions to run on power loss
                                
                                G28                                                 ; home
                                
                                ; bed.g
                                ; called to perform automatic bed compensation via G32
                                ;
                                ; generated by RepRapFirmware Configuration Tool v3.2.1 on Mon Jan 18 2021 17:44:49 GMT+0100 (Mitteleuropäische Normalzeit)
                                M561     ; clear any bed transform
                                G28      ;home
                                G29 S1   ; probe the bed and enable compensation
                                M280 P0 S90 ; retractProbe
                                
                                ; homez.g
                                ; called to home the Z axis
                                ;
                                ; generated by RepRapFirmware Configuration Tool v3.2.1 on Mon Jan 18 2021 17:44:49 GMT+0100 (Mitteleuropäische Normalzeit)
                                G91               ; relative positioning
                                G1 H2 Z10 F6000   ; lift Z relative to current position
                                G1 H1 Z-500 F3000 ;Go down till endstop
                                G1 H2 Z10 F6000
                                G1 X200 Y200 F4000 ;go to midle
                                G30 ; move Z down until the endstop is triggered
                                G92 Z0         ; set Z position to axis minimum (you may want to adjust this)
                                
                                
                                
                                ; Uncomment the following lines to lift Z after probing
                                ;G91              ; relative positioning
                                ;G1 Z10 F100      ; lift Z relative to current position
                                G90              ; absolute positioning
                                
                                ; homeall.g
                                ; called to home all axes
                                ;
                                ; generated by RepRapFirmware Configuration Tool v3.2.1 on Mon Jan 18 2021 17:44:49 GMT+0100 (Mitteleuropäische Normalzeit)
                                
                                ;DUAL Z 
                                M584 Z2:4   
                                
                                M280 P0 S90
                                G91                     ; relative positioning
                                G1 H2 Z10 F6000         ; lift Z relative to current position
                                G1 H1 X-405 Y-405 F5000 ; move quickly to X and Y axis endstops and stop there (first pass)
                                G1 H2 X5 Y5 F6000       ; go back a few mm
                                G1 H1 X-405 Y-405 F360  ; move slowly to X and Y axis endstops once more (second pass)
                                M98 Phomez.g            ; move Z down stopping at the endstop
                                G90                     ; absolute positioning
                                G92 Z10                 ; set Z position to axis minimum (you may want to adjust this)
                                
                                ; Uncomment the following lines to lift Z after probing
                                ;G91                    ; relative positioning
                                ;G1 Z10 F100            ; lift Z relative to current position
                                ;G90                    ; absolute positioning
                                
                                
                                

                                yaa its my current

                                fcwiltundefined 1 Reply Last reply Reply Quote 0
                                • fcwiltundefined
                                  fcwilt @TristanKoeln
                                  last edited by

                                  @TristanKoeln

                                  Thanks.

                                  So if they are current there are two things wrong that may be causing you problems.

                                  In homeZ.g there is that G92 Z0 after the G30 that is setting the Z position incorrectly. Since the G30 leaves Z in a known position you can simply remove the G92 Z0 or if you wish to move Z to some other known position you can use something like G90 G1 Z10.

                                  In homeALL.g there is G92 Z10 after the call to homeZ.g which again will set the Z position incorrectly.

                                  And the M584 command is not needed since it occurs in your config.g file.

                                  What is the intent of the M280 P0 S90 command? If you issue deploy/retract commands using M280 instead of M401/M402 then the firmware may lose track of the state of the probe.

                                  Frederick

                                  Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                                  1 Reply Last reply Reply Quote 0
                                  • TristanKoelnundefined
                                    TristanKoeln
                                    last edited by

                                    so i edit the files

                                    ; homez.g
                                    ; called to home the Z axis
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v3.2.1 on Mon Jan 18 2021 17:44:49 GMT+0100 (Mitteleuropäische Normalzeit)
                                    G91               ; relative positioning
                                    G1 H2 Z10 F6000   ; lift Z relative to current position
                                    G1 H1 Z-500 F3000 ;Go down till endstop
                                    G1 H2 Z10 F6000
                                    G1 X200 Y200 F4000 ;go to midle
                                    G30 ; move Z down until the endstop is triggered
                                    ;G92 Z0        ; set Z position to axis minimum (you may want to adjust this)
                                    
                                    
                                    
                                    ; Uncomment the following lines to lift Z after probing
                                    ;G91              ; relative positioning
                                    ;G1 Z10 F100      ; lift Z relative to current position
                                    G90              ; absolute positioning
                                    
                                    
                                    ; homeall.g
                                    ; called to home all axes
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v3.2.1 on Mon Jan 18 2021 17:44:49 GMT+0100 (Mitteleuropäische Normalzeit)
                                    
                                    ;DUAL Z 
                                    ;M584 Z2:4   
                                    
                                    M280 P0 S90
                                    G91                     ; relative positioning
                                    G1 H2 Z10 F6000         ; lift Z relative to current position
                                    G1 H1 X-405 Y-405 F5000 ; move quickly to X and Y axis endstops and stop there (first pass)
                                    G1 H2 X5 Y5 F6000       ; go back a few mm
                                    G1 H1 X-405 Y-405 F360  ; move slowly to X and Y axis endstops once more (second pass)
                                    M98 Phomez.g            ; move Z down stopping at the endstop
                                    G90                     ; absolute positioning
                                    G92 Z10                ; set Z position to axis minimum (you may want to adjust this)
                                    
                                    ; Uncomment the following lines to lift Z after probing
                                    ;G91                    ; relative positioning
                                    ;G1 Z10 F100            ; lift Z relative to current position
                                    ;G90                    ; absolute positioning
                                    
                                    

                                    i got the nozzel once close to the bed.. to close after i made the calibration process again the problem from the start came back

                                    fcwiltundefined 1 Reply Last reply Reply Quote 0
                                    • TristanKoelnundefined
                                      TristanKoeln
                                      last edited by

                                      @fcwilt and the M280 is just to move the pin in a save position just incase it isnt

                                      1 Reply Last reply Reply Quote 0
                                      • fcwiltundefined
                                        fcwilt @TristanKoeln
                                        last edited by

                                        @TristanKoeln said in Heigh error after calibrating:

                                        i got the nozzel once close to the bed.. to close after i made the calibration process again the problem from the start came back

                                        Did you leave the G92 Z10 in homeALL.g?

                                        And did you understand what I meant about the firmware losing track of the state of the probe if you didn't use M401/M402?

                                        Frederick

                                        Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                                        1 Reply Last reply Reply Quote 0
                                        • TristanKoelnundefined
                                          TristanKoeln
                                          last edited by

                                          @fcwilt the G92 is only in the home all file ;
                                          not realy

                                          fcwiltundefined 1 Reply Last reply Reply Quote 0
                                          • fcwiltundefined
                                            fcwilt @TristanKoeln
                                            last edited by

                                            @TristanKoeln said in Heigh error after calibrating:

                                            @fcwilt the G92 is only in the home all file ;

                                            Just before that G92 Z10 you have a call to homeZ.g which executes a G30 and sets the Z=0 Datum and leaves the Z position at dive height + Z trigger height.

                                            You can't just tell the firmware with a G92 that the Z position is something else and expect things to work.

                                            You can change the actual Z position with a G1 Znnn command but not with a G92 command.

                                            not realy

                                            When you use M401/M402 the firmware keeps track of the state of the probe (retracted/deployed).

                                            When you use the M280 command to retract/deploy the actual state of the probe and what state the firmware thinks the probe is in may conflict and possibly cause problems.


                                            Frederick

                                            Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                                            1 Reply Last reply Reply Quote 1
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA