Scara support ?

dc42

I've just done that.

frafa

Hello
A big thank you for all your work!

My end-stop limit is not exactly in X0 / Y0
Before with smoothie I used M206 to specify offset and move on real X0/Y0 after homing

How to do with ReprapFirmware?

dc42

Your endstops need to be at one end of each of the proximal and distal joint limits as described in the wiki. They detect the limits of movements of the joint angles. Those limits are wherever you say they are in the M669 command.

frafa

ok I understood
I test tomorrow the scara is at the fablab

It is posible to move x / y after homing on scara and to redefine origin with with G92 x0 y0? (I wish to work only in the square of the bed)

In the documentation the command M669 I no longer see the X and Y parameters
https://duet3d.com/wiki/Configuring_RepRapFirmware_for_a_SCARA_printer

Example for me
K4 P200 D200 A-175: 175 B-175: 175 1: 0: 0 S200 T0.1 X84.0 Y-150.0;
How the calculation is done if we do not specify or is X0 / Y0 with respect to the axis

dc42

No you can't redefine the origin with G92. However, you can use the M669 X and Y parameters to set the origin wherever you like, as we discussed previously.

The way the calculation is done is as follows:

The X axis is the direction that the proximal arm points along when its angle is zero. You can choose where you consider the zero angle to be, however it would generally be sensible to have it near the middle of its range of movement. When you have chosen the position that you consider to be zero angle, that determines what the minimum and maximum angles are, which you specify in the M669 D P parameters (and either the minimum or the maximum one is the trigger point of the proximal joint homing switch).
The zero angle of the distal joint is defined as the angle when both arms are lined up.
If you specify X and Y offsets of zero in the M669 command, then X0 Y0 will be the position of the axis of the proximal joint (which is an unreachable position in most SCARA architectures). So specify X and Y in the M669 command relative to that. I would expect that in a typical case, the X offset will be positive by an amount somewhat smaller than the square printable X range, and the Y offset will be negative by about half the square printable Y range.

I will add this info to the wiki.

There is a SCARA printer kit on its way to me, so I should be able to test all of this in a couple of weeks.

HTH David

EDIT: I've corrected the above text, and added it and a Calibration section to the wiki page.

frafa

OK
So for the moment I am obliged to declare in M669 xxx / yyy exactly at the position of the endstops

No way to shift the origins to have x0 / y0 at the exact angle of the bed?

dc42

Where are your endstops, and what sort are they? Photo?

frafa

The end stop are hall effect, Logic on 3.3v / v + on 5v
Photos and tests tomorrow scara is at fablab …

Edit:
I need to be able to shift the position after homing to x0 / y0
Either with M206
Either with G92 after move on x0/y0
how to do ?

frafa

Hello,

The X/Y travel limiters do not set to zero Z is ok
All End-Stops are well detected the engines stop

My config
Firmware Name: RepRapFirmware for Duet WiFi
Firmware Electronics: Duet WiFi 1.0
Firmware Version: 1.19RC5 (2017-08-06)
WiFi Server Version: 1.19beta10
Web Interface Version: 1.17+2

My file homeall.g

[[language]]
; File homeall.g
;G91                ; relative movement
;G1 Z4 F100         ; ensure head is clear of the bed

; Home proximal joint
G91
G1 S1 X-200 F3000  ; move proximal joint clockwise by up to 200 degrees until the endstop switch is triggered
G1 S2 X5          ; move proximal joint anticlockwise by 10 degrees
G1 S1 X-20 F300    ; move proximal joint slowly to the endstop switch again
G90                ; absolute movement
;G1 S2 X0 F3000     ; move proximal joint to centre of range

; Home distal joint
G91                ; relative movement
G1 S1 Y200 F3000   ; move distal joint clockwise by up to 200 degrees until the endstop switch is triggered
G1 S2 Y-5         ; move distal joint anticlockwise by 10 degrees
G1 S1 Y20 F300     ; move distal joint slowly to the endstop switch again
G90                ; absolute movement
;G1 S2 Y0 F3000    ; move distal joint to centre of range

; Home Z
G91                ; relative movement
G1 S1 Z400 F250    ; ensure head is clear of the bed
;G1 S2 Z10          ; move proximal joint anticlockwise by 10 degrees
;G1 S1 Z-20 F100    ; move proximal joint slowly to the endstop switch again
G90                ; absolute movement

My file config.g

[[language]]
; General preferences
M111 S0 ; S0 Debugging off S1 ; Debugging on
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P2 ; Set firmware compatibility to look like Marlin
M208 X0 Y0 Z0 S1 ; Set axis minima
M208 X300 Y300 Z380 S0 ; Set axis maxima

; Endstops
M574 X1 Y1 S0 ; Define active low microswitches
M574 Z2 S0    ; Define active high microswitches

; Drives - Axis and motor configuration
M569 P0 S0                    ; Drive 0 (X) goes forwards
M569 P1 S1                    ; Drive 1 (Y) goes forwards
M569 P2 S1                    ; Drive 2 (Z) goes forwards
M569 P3 S0                    ; Drive 3 (E0) goes forwards
;M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M350 X256 Y256 Z16 E16 I1 ; Configure 256 microstepping with interpolation

;Calcul Step/mm X/Y (Réduction 80/16) ==> 400*256*(160/16)/360=2844,4444444444444444444444444444
;Calcul Step/mm Z   (Réduction 51/1)  ==> 200*256*51/2.0/20=6528
M92 X2844,4444444444444444444444444444 Y2844,4444444444444444444444444444 Z4080 E550 ; Set steps per mm
M566 X300 Y300 Z15 E75 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z300 E1500 ; Set maximum speeds (mm/min)
M201 X300 Y300 Z250 E800 ; Set accelerations (mm/s^2)
M906 X1400 Y1400 Z1400 E1000 I60 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
M669 K4 P200 D200 A-175:175 B-175:175 1:0:0 S150 T0.1 X85.0 Y-150.0; set SCARA kinematics parameters ok S200

Upload video in progress catastrophic connection to fablab …

frafa

Video
http://dl.free.fr/jhn5CLUfH

frafa

if i send

[[language]]
SENDING:G28 X0
Homing file homeproximal.g not found

[[language]]
SENDING:G28 Y0
Homing file homedistal.g not found

poroblem is here ?

dc42

I've just corrected the wiki page about configuring a SCARA printer. The proximal joint and distal joint homing files are called homeproximal.g and homedistal.g, not homep.g and homed.g as I documented originally.

frafa

Hi

Added files
same problem G28 wont reset coordonate X/Y (Z ok)
position is ok motor stop but X/Y Does not go to zero

see video
http://dl.free.fr/jhn5CLUfH

frafa

if i test just

[[language]]
G1 S1 X-200 F3000

```move ok
stop position ok
but not Zero coordonate ….

number40fan

Nvm, got the video to finally download.

frafa

Hi

[[language]]
G1 S1 X-200 F3000

```Wont reset zero coordonate, Bug ?

dc42

@frafa:

I need to be able to shift the position after homing to x0 / y0
Either with M206
Either with G92 after move on x0/y0
how to do ?

To shift the X=0 Y=0 point:

1. Make sure that you have set the arm angle limits in the M669 command P and D parameters accurately, so that when you home the arms the homing switches trigger at those angles.

2. To verify this, after homing, send G0 X0 Y0 S2 F2000. This will send both arms to zero angle. Check that both arms are pointing along the direction that you have chosen for the X axis. Note: The "arms" are the lines from the proximal joint to the distal joint, and from the distal joint to the nozzle. These are the lines that must both point along the X axis at zero angle. If you have joints and/or the nozzle offset to one side from the physical arm, then the physical arm will not point along the X axis.

3. The X and Y parameters in the M669 command specify the X and Y offsets of (0,0) from the location of the distal joint. If you send G0 X0 Y0 F2000 (without the S2 modifier) then it will go to that position. You can put this command at the end of your homeall.g file if you wish. If this doesn't send the head to where you want X0 Y0, and step #2 above worked correctly, then you need to adjust the X and/or Y parameters.

frafa

Hello
Sorry but I do not understand …

@dc42:

1. Make sure that you have set the arm angle limits in the M669 command P and D parameters accurately, so that when you home the arms the homing switches trigger at those angles.

M669 P and D commands are the lengths of the arms?
You are talking about Annn: mmm and Bnnn: mmm?

Is it possible that you give me the approximate values (aaa … bbb) by looking at my schema as I understand the sense of the measurement of angles? compared to what ?

M669 K4 P200 D200 A??? B??? 1:0:0 S150 T0.1 X65.0 Y-150.0; set SCARA kinematics parameters ok S200

dc42

I find it easier to understand if I rotate that diagram by 180 degrees so that +X is to the right and +Y is up.

If the diagram shows the arms in the homed position (i.e. both arm joint microswitches triggered), then the homing position of the proximal joint is about -120 degrees. So your P parameter should be -120:xxx where xxx is the maximum angle it can rotate anticlockwise relative to the X axis.

The distal joint appears to me to be at an angle of approximately +150 degrees relative to the proximal arm. So the D parameter should be -yyy:150 where yyy is the maximum angle it can reach clockwise relative to the proximal arm.

The proximal arm homes fully clockwise (bottom end of its range) whereas the distal arm homes fully anticlockwise (top end of its range). So your M574 X and Y parameters need to be X1 Y2.

See the expanded calibration section at https://duet3d.com/wiki/Configuring_RepRapFirmware_for_a_SCARA_printer#Calibration.

frafa

Hello
I do not understand why you talk about P and D
P and D are the length of the arms?

Tonight we were 4 people at the fablab to try to understand
Not successful …
I rework on scara Monday