Error: New tool too close to Z axis limit. ?

peter247

@dc42 Yes , after a little think I guessed that is what the error message meant , But I had only just switched it on and the tool was where I left it the previous day at about 25mm from the tool.

dc42

@peter247 did you home Z before attempting the tool change?

peter247

@dc42 No homing at all , just switch on the printer and started heating the bed to 60c,
Told it to print and got the error , But told it to print the second time I didn't get a error .
I think the firmware / mpu was have a bad day !!!

dc42

@peter247 maybe the print file commands a tool change before Z has been homed?

Phaedrux

@dc42 said in Error: New tool too close to Z axis limit. ?:

@peter247 maybe the print file commands a tool change before Z has been homed?

The slicer must be selecting a tool because there is no T0 in config.g or his slicer start gcode.

@peter247 can you share the first 50 lines or so of your gcode file?

peter247

@phaedrux

This isn't the gcode which errored , but haven't changed anything in my start code .

;FLAVOR:RepRap
;TIME:11613
;Filament used: 8.26945m
;Layer height: 0.2
;MINX:127.228
;MINY:135.862
;MINZ:0.2
;MAXX:168.88
;MAXY:170.83
;MAXZ:80
;Generated with Cura_SteamEngine 4.10.0
T0
M190 S60
M104 S200
M109 S200
M82 ;absolute extrusion mode
G28 ;Home
;G29
G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up
G1 X0.1 Y30 Z0.28 F5000.0 ;Move to start position
G1 X0.1 Y290.0 Z0.28 F1500.0 E25 ;Draw the first line
G1 X0.4 Y290.0 Z0.28 F5000.0 ;Move to side a little
G1 X0.4 Y30 Z0.28 F1500.0 E30 ;Draw the second line
G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up
M300 S300 P1000
G92 E0
G92 E0
G1 F5100 E-0.3
;LAYER_COUNT:400
;LAYER:0
M107
G0 F2880 X128.628 Y136.722 Z0.2
;TYPE:SKIRT
G1 F2040 E0
G1 F1200 X129.078 Y136.406 E0.02378
G1 X129.569 Y136.159 E0.04754
G1 X130.09 Y135.986 E0.07128
G1 X130.632 Y135.891 E0.09507
G1 X130.911 Y135.872 E0.10716
G1 X131.232 Y135.863 E0.12105
G1 X134.859 Y135.862 E0.27787
G1 X135.557 Y135.872 E0.30805
G1 X135.867 Y135.89 E0.32148
G1 X136.607 Y135.962 E0.35363
G1 X139.326 Y136.192 E0.47161
G1 X142.04 Y136.345 E0.58915
G1 X144.795 Y136.422 E0.70831
G1 X147.516 Y136.42 E0.82597

I only have one tool ( 0 ) and didn't I select it by making the heater active ?

Phaedrux

@peter247 said in Error: New tool too close to Z axis limit. ?:

I only have one tool ( 0 ) and didn't I select it by making the heater active ?

Which heater did you make active? You mention setting the bed heater to 60.

peter247

@phaedrux The bed heater .

I can now reproduce the error now I know what it is !!!!

( 1 ) switch it on , don't home . ( Tool position X Y Z all zero )
( 2 ) Baby step with a minus offset value.
( 3 ) Print !!!! and you get the error .
( 4 ) Print again and it prints .

Phaedrux

@peter247 said in Error: New tool too close to Z axis limit. ?:

( Tool position X Y Z all zero )

What do you mean by this? Are you manually setting the positions? If you haven't homed yet how do you know what the tool position is?

Are you baby stepping before anything has been homed or a tool has been selected?

When you start the print, the first command it does is select T0. then sets some temps, and then homes.

Since you only have a single tool, you should add T0 to the end of your config.g so that it is selected at startup.

Then only baby step after you've homed.

peter247

@phaedrux said in Error: New tool too close to Z axis limit. ?:

@peter247 said in Error: New tool too close to Z axis limit. ?:

( Tool position X Y Z all zero )

What do you mean by this? Are you manually setting the positions? If you haven't homed yet how do you know what the tool position is?

Are you baby stepping before anything has been homed or a tool has been selected?

When you start the print, the first command it does is select T0. then sets some temps, and then homes.

Since you only have a single tool, you should add T0 to the end of your config.g so that it is selected at startup.

Then only baby step after you've homed.

I just mean that the web interface says Tool position all zero , not that the tool head is at a known position.

Yes I set a baby step before I homed it

o.k I'll add T0 to the end of my config.g

I think that is a solved now .