Duet 2 Wifi + Bltouch

Btj

@chrishamm said in Duet 2 Wifi + Bltouch:

M950 S0 C"duex.pwm1

M950 S0 C"duex.pwm1
Warning: M950 command is not supported

chrishamm

@btj It sounds like you are still using RRF2, so it may be a good idea to upgrade to RRF3. If you don't want to upgrade, see https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_Software_setup_Duet_2_WiFi_Ethernet_running_RepRapFirmware_Num_2 for further instructions.

droftarts

@btj Your config.g is a mix of commands for RepRapFirmware 2 and RepRapFirmware 3. Please send M115 and post response, so we can see what firmware version you are running. Then we can best advise you on the correct commands.

Ian

Btj

@droftarts
M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.05.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-02-09b1

droftarts

@btj said in Duet 2 Wifi + Bltouch:

FIRMWARE_VERSION: 2.05.1

If you're not planning on updating the firmware to the current version (v3.3, but see update instructions here: https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware#Section_Updating_from_RRF_2_x_to_3_x ), then it will be easiest to regenerate your configuration files using the Configuration tool https://configtool.reprapfirmware.org/Start
This is because you have generated a configuration for RRF 3, see first line of your config.g:

; Configuration file for Duet WiFi (firmware version 3)

I expect currently none of your temperature responses will be correct, fans won't work, and there will be no tool, as well as the probe not working. All the lines in config.g that have C or P parameter with "[something in quotes]" will need to change, so it's easier to regenerate the files with the correct firmware version selected. On the https://configtool.reprapfirmware.org/General page, under "Firmware version:" make sure you select "2.03 to 2.05".

If you want to update to RRF v3.3, your existing config should work, but you need to tidy up your Z-probe configuration. See @chrishamm's post earlier.

Ian

Btj

@droftarts
M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.0 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-01-03b3

droftarts

@btj said in Duet 2 Wifi + Bltouch:

FIRMWARE_VERSION: 3.0

Now update to RRF v3.3. https://github.com/Duet3D/RepRapFirmware/releases/tag/3.3

Ian

Btj

@droftarts
M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.3 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2021-06-15 21:45:03

droftarts

@btj Have you made any changes to your config.g? If so, please post your current config.g.
From your earlier config.g, you will need to change your Endstop and Z-Probe sections. They should look something like this:

; Endstops
M574 X1 S1 P"xstop"                            ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                            ; configure active-high endstop for low end on Y via pin ystop

; Z-Probe
M950 S0 C"exp.heater3"                         ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000            ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y0 Z2.5                            ; set Z probe trigger value, offset and trigger height

Remove these lines:

M574 Z[anything]
M307 H3 A-1 C-1 D-1
M307 H7 A-1 C-1 D-1 ; Disable the 7th Heater to free up PWM channel 5 on the Duex board.
Any other M950, M558 and G31 lines

Then post your config.g so we can check it.

Ian

Btj

@droftarts
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Ender 5 Plus" ; set printer name

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E156.47 ; set steps per mm
M566 X900.00 Y900.00 Z80.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z300.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z30.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X350 Y350 Z400 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; X min active high endstop switch
M574 Y1 S1 P"ystop" ; Y min active high endstop switch
M574 Z1 S1 P"zstop" ; Z min active high endstop switch
M574 U2 S1 P"e0stop" ; U max active high endstop switch
M558 P9 C"^zprobe.in" H5 F100 T2000

G31 X0 Y0 Z 0 P25

Z-Probe

M307 H3 A-1 C-1 D-1
M558 P9 C"^zprobe.in" H5 F100 T2000
M950 S0 C"exp.heater3"
G31 X-50 Y-11.02 Z 0 P25
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H7 A-1 C-1 D-1 ; Disable the 7th Heater to free up PWM channel 5 on the Duex board.
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

droftarts

@btj said in Duet 2 Wifi + Bltouch:

; Endstops
M574 X1 S1 P"xstop" ; X min active high endstop switch
M574 Y1 S1 P"ystop" ; Y min active high endstop switch
M574 Z1 S1 P"zstop" ; Z min active high endstop switch
M574 U2 S1 P"e0stop" ; U max active high endstop switch
M558 P9 C"^zprobe.in" H5 F100 T2000
G31 X0 Y0 Z 0 P25
Z-Probe
M307 H3 A-1 C-1 D-1
M558 P9 C"^zprobe.in" H5 F100 T2000
M950 S0 C"exp.heater3"
G31 X-50 Y-11.02 Z 0 P25
; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H7 A-1 C-1 D-1 ; Disable the 7th Heater to free up PWM channel 5 on the Duex board.
M140 H0 ; map heated bed to heater 0

Remove:

M574 Z1 S1 P"zstop" ; Z min active high endstop switch
M574 U2 S1 P"e0stop" ; U max active high endstop switch
M558 P9 C"^zprobe.in" H5 F100 T2000
G31 X0 Y0 Z 0 P25
...
M307 H3 A-1 C-1 D-1
...
M307 H7 A-1 C-1 D-1 ; Disable the 7th Heater to free up PWM channel 5 on the Duex board.

Ian