Issues after prime

Heartleander81

Any other Propeller use 50-70mm/s retract speed. There is my 20 very slow.

Without filament I can speed the extruder high. With optimal print Temp and filament can I extrude ~20mm/s.

I have this 20mm/s use the last 6-8 month without Problem.

Any time I have step lost on X and Y

Heartleander81

If you look at this video you can see how the car brakes hard by braking and starting again and then continues jerking, and the belts wobble a lot. Depending on how it vibrates, the motors lose steps and I no longer print in the middle. In the long run, the jerking is not healthy for the whole mechanics

Heartleander81

@phaedrux

But the question is why run the extruder to 0 and back to 99.4 when M83 is Configured?

When I All write to M82 and slice M82 is the same problem. At this one Point reset the firmware not the extruder.

Heartleander81

That Video is with a another Purge line.

There is with step lost on X and Y. The print must start on the middle on x150 Y150 but is in the left back corner.

https://youtu.be/UaVkC-F1cfM

Phaedrux

Have you tested in standalone mode yet without the SBC?

https://duet3d.dozuki.com/Wiki/Getting_Started_With_Duet_3#Section_Running_in_standalone_mode

Heartleander81

@phaedrux no. I dount have standalone configured

Phaedrux

As process of elimination it may help to know if the problem still presents in standalone mode.

You can copy your current config files onto a fresh SD card that has the folder structure and DWC files present and use that SD card in the Duet. That link describes in more detail.

Heartleander81

@Phaedrux
Ok have I do.

Heartleander81

@phaedrux
The same on standalone

Heartleander81

That came after 2 weeks after I have install the toolboard 1lc V1.1

Heartleander81

Should I reset the toolboard?
By pressing both buttons on the toolboard when starting.
Reload the board firmware and then test it again?
After install the Bus change to 20.

Phaedrux

Thanks for testing in standalone mode. Before you do anything to the toolboard, let's let @dc42 have a look and see what he thinks.

Heartleander81

@phaedrux

Ok.

dc42

@heartleander81 said in Isusses after prime:

That Video is with a another Purge line.

There is with step lost on X and Y. The print must start on the middle on x150 Y150 but is in the left back corner.

https://youtu.be/UaVkC-F1cfM

Please can you provide the start of the GCode file that you were printing when you recorded this video.

I suspect that a firmware issue is causing this behaviour.

Heartleander81

@dc42
Good Morning.

G90
M83
M106 S0
M140 S50
M190 S50
M104 S240 T0
M109 S240 T0
T0
M98 P"startGcode"
G92 E0.0
; process CR3D 0.4
; layer 1, Z = 0.200
T0
G1 E-0.6000 F1200
; feature skirt
; tool H0.200 W0.440
G1 Z0.200 F600
G1 X118.950 Y122.494 F12600
;G1 X19.489 Y53.567 F12600
;G1 E0.6000 F1200
;G1 X280.511 Y53.567 E8.9768 F1800
; layer end
T0
M98 P"endGcode"

Unfortunately, I no longer have the file from the print. Do you mean the purge line in the startup code?

Thanks for your Help.

dc42

@heartleander81 thanks, to try to reproduce this I also need the contents of macros startGCode and endGcode. [Edit: I see that you have already provided startGcode, so I will try to reproduce it.

Heartleander81

@dc42

startGcode

M150 U255 P128 S60 ;LED gruen
M150 R255 B235 U255 P128 S60 ;LED weiß
G32
G29 S1 P"heightmap.csv"
M83
G1 X5 Y5 Z30 F6000.0 
G1 E50 F500
G1 E30 F200
G1 Y20 F2000
G1 Y50 Z0.2 F3000
G1 Y90 E20 F300
G1 Y120 F1200
M150 R255 B235 U255 P128 S60 ;LED weiß

endGcode

G10 P0 R0 S0		        ; Set hotend temp to 0
M140 S0			            ; Set bed temp to 0
G91
G1 Z10
G90
G92 E0
G1 E-1 F300
G92 E0
M106 S20 		            ; Fan to cool nozzle and bed
M220 S100		            ; Set speed factor back to 100% in case it was changed
M221 S100		            ; Set extrusion factor back to 100% in case it was changed
M290 R0 S0
G1 X25 Y300 F6000
G1 E-9 F200
G92 E0 
M300 S290 P1000
M150 U255 P128 S60 ;LED gruen
G4 S60		            	; wait 1 minute for nozzle to cool
M107			            ; turn off the fan
G4 S30
M98 P"/macros/LED/LED_Aus"
M18

dc42

@heartleander81 thanks! Do you have any tool change files on your system?

Heartleander81

@dc42 no I don't have tool change file. The tool Board 1lc 1v1 is direkt conected to the duet6 6hc Board.

Heartleander81

@dc42 in the last 2 file is only write M116 P0