Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. Heartleander81
    • Profile
    • Following 0
    • Followers 0
    • Topics 16
    • Posts 277
    • Best 14
    • Controversial 0
    • Groups 0

    Heartleander81

    @Heartleander81

    15
    Reputation
    11
    Profile views
    277
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    Heartleander81 Unfollow Follow

    Best posts made by Heartleander81

    • RE: Issues with pressure advance since RRF 3.4

      Update on my conversion to Klipper.
      At first the corners didn't look any better than with RRF until I came across a post today that refers to extruder smooth time.
      The standard is with Klipper 0.04, which I also use.
      Switched to 0.01 and the corners look awesome.
      In the article it was said that some extruders can not cope with the smooth time and then you have to get smaller. see my pictures.

      20221121_171555.jpg

      With smooth time 0.04

      20221128_153229.jpg 20221128_153233.jpg 20221128_153236.jpg

      With smooth time 0.01

      posted in General Discussion
      Heartleander81undefined
      Heartleander81
    • RE: InputShaping-Plugin-0.2.0-pre3 released

      @jay_s_uk many thanks. It work and install is done

      posted in Plugins for DWC and DSF
      Heartleander81undefined
      Heartleander81
    • RE: 2 Component Fans

      @Phaedrux I have write T0 at custom settings are not defined and save the config.g.

      I am so happy.

      posted in Firmware installation
      Heartleander81undefined
      Heartleander81
    • RE: Bl-Touch self extended

      @Veti

      Found the bug. It was due to the contact resistance at the on-board connection. I thank you for the help and patience

      posted in General Discussion
      Heartleander81undefined
      Heartleander81
    • RE: 3.2 SBC cancel print not working w/ missing/blank cancel.g

      @fcwilt i mean the config post from phaedrux

      posted in Beta Firmware
      Heartleander81undefined
      Heartleander81
    • RE: InputShaping Plugin shows only zeros with Toolboard 1lc

      @dc42
      M122

      M122
      === Diagnostics ===
      RepRapFirmware for Duet 3 MB6HC version 3.4.0beta4 (2021-09-27 11:31:18) running on Duet 3 MB6HC v1.01 or later (SBC mode)
      Board ID: 08DJM-9P63L-DJ3T8-6J1DA-3SD6P-KV4H9
      Used output buffers: 1 of 40 (15 max)
      === RTOS ===
      Static ram: 151080
      Dynamic ram: 63896 of which 192 recycled
      Never used RAM 131712, free system stack 127 words
      Tasks: SBC(ready,61.0%,248) HEAT(notifyWait,1.9%,321) Move(notifyWait,6.9%,238) CanReceiv(notifyWait,0.2%,772) CanSender(notifyWait,0.1%,362) CanClock(delaying,0.8%,339) TMC(notifyWait,79.4%,58) MAIN(running,101.7%,921) IDLE(ready,0.3%,30), total 252.3%
      Owned mutexes: HTTP(MAIN)
      === Platform ===
      Last reset 107:37:24 ago, cause: software
      Last software reset at 2021-10-03 21:00, reason: User, GCodes spinning, available RAM 132020, slot 2
      Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
      Error status: 0x00
      Aux0 errors 0,0,0
      Step timer max interval 18672
      MCU temperature: min 30.3, current 33.6, max 46.0
      Supply voltage: min 0.2, current 25.2, max 25.5, under voltage events: 0, over voltage events: 0, power good: yes
      12V rail voltage: min 0.2, current 12.1, max 12.9, under voltage events: 12
      Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/432/432, gc cycles 0
      Driver 0: pos 27529, standstill, SG min/max 0/1023, reads 44026, writes 238 timeouts 1
      Driver 1: pos 5114, standstill, SG min/max 0/1023, reads 44016, writes 248 timeouts 1
      Driver 2: pos 3729, standstill, SG min/max 0/1023, reads 44016, writes 248 timeouts 1
      Driver 3: pos 0, standstill, SG min/max 0/1023, reads 44026, writes 238 timeouts 1
      Driver 4: pos 0, standstill, SG min/max 0/1023, reads 44026, writes 238 timeouts 1
      Driver 5: pos 0, standstill, SG min/max 0/0, reads 44121, writes 143 timeouts 1
      Date/time: 2021-10-08 08:38:24
      Slowest loop: 1027.96ms; fastest: 0.03ms
      === Storage ===
      Free file entries: 10
      SD card 0 not detected, interface speed: 37.5MBytes/sec
      SD card longest read time 0.0ms, write time 0.0ms, max retries 0
      === Move ===
      DMs created 125, segments created 39, maxWait 158836857ms, bed compensation in use: none, comp offset 0.000
      === MainDDARing ===
      Scheduled moves 73991, completed 73991, hiccups 0, stepErrors 0, LaErrors 0, Underruns [6, 0, 4], CDDA state -1
      === AuxDDARing ===
      Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
      === Heat ===
      Bed heaters = 0 6 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
      === GCodes ===
      Segments left: 0
      Movement lock held by null
      HTTP* is doing "M122" in state(s) 0
      Telnet is idle in state(s) 0
      File* is idle in state(s) 0
      USB is idle in state(s) 0
      Aux is idle in state(s) 0
      Trigger* is idle in state(s) 0
      Queue* is idle in state(s) 0
      LCD is idle in state(s) 0
      SBC is idle in state(s) 0
      Daemon is idle in state(s) 0
      Aux2 is idle in state(s) 0
      Autopause is idle in state(s) 0
      Code queue is empty
      === CAN ===
      Messages queued 3803959, received 709539, lost 0, longest wait 97ms for reply type 6013, peak Tx sync delay 60699, free buffers 49 (min 19), ts 1937222/177401/0
      Tx timeouts 0,0,1759820,0,0,1407845 last cancelled message type 30 dest 127
      === SBC interface ===
      State: 4, failed transfers: 0, checksum errors: 0
      Last transfer: 2ms ago
      RX/TX seq numbers: 13800/13800
      SPI underruns 0, overruns 0
      Disconnects: 0, timeouts: 0, IAP RAM available 0x2c488
      Buffer RX/TX: 0/0-0
      === Duet Control Server ===
      Duet Control Server v3.4-b4
      Code buffer space: 4096
      Configured SPI speed: 8000000Hz
      Full transfers per second: 39.62, max wait times: 73.8ms/21.3ms
      Codes per second: 1.46
      Maximum length of RX/TX data transfers: 6916/1688
      

      M122 B20

      M122 B20
      Diagnostics for board 20:
      Duet TOOL1LC rev 1.1 or later firmware version 3.4.0beta4 (2021-09-27 14:41:33)
      Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)
      Never used RAM 2632, free system stack 2768 words
      Tasks: Move(notifyWait,0.0%,153) HEAT(notifyWait,0.2%,115) CanAsync(notifyWait,0.0%,58) CanRecv(notifyWait,0.0%,77) CanClock(notifyWait,0.0%,64) ACCEL(notifyWait,0.0%,27) TMC(delaying,3.0%,57) MAIN(running,91.8%,346) IDLE(ready,0.0%,27) AIN(delaying,4.9%,142), total 100.0%
      Last reset 00:11:53 ago, cause: VDD brownout
      Last software reset data not available
      Driver 0: pos 0, 718.0 steps/mm, standstill, SG min/max 0/0, read errors 0, write errors 0, ifcnt 12, reads 28998, writes 12, timeouts 0, DMA errors 0, steps req 0 done 0
      Moves scheduled 0, completed 0, in progress 0, hiccups 0, step errors 0, maxPrep 0, maxOverdue 0, maxInc 0, mcErrs 0, gcmErrs 0
      Peak sync jitter 1/5, peak Rx sync delay 611, resyncs 0/0, no step interrupt scheduled
      VIN: 25.4V
      MCU temperature: min 25.6C, current 42.9C, max 42.9C
      Ticks since heat task active 166, ADC conversions started 713409, completed 713409, timed out 0, errs 0
      Last sensors broadcast 0x00000002 found 1 171 ticks ago, loop time 0
      CAN messages queued 14372, send timeouts 0, received 6473, lost 0, free buffers 37, min 37, error reg 0
      dup 0, oos 0/0/0/0, bm 0, wbm 0, rxMotionDelay 0
      Accelerometer detected: yes, status: 00
      I2C bus errors 0, naks 3, other errors 0
      
      posted in Plugins for DWC and DSF
      Heartleander81undefined
      Heartleander81
    • RE: Issues with pressure advance since RRF 3.4

      I have this corner issuse to.
      My System

      Duet 3 6 hc SBC
      Duet 3 1lc
      Rapido Hotend
      Hextrudort Extruder ( ~ 20mm tube from extruder to hotend )

      Test with extruder on toolboard and on the MB direkt but the corners issuse ob both connection.
      Test with IS on and off at both connection.
      My PA bevor the issuse was 0.035.
      When I turned up the PA to 0.04, the wall on the corners open it.

      Need you more Info?
      Config.g?
      M122?

      I print a simple Cube with 40x40x2mm

      posted in General Discussion
      Heartleander81undefined
      Heartleander81
    • RE: 3.2 SBC cancel print not working w/ missing/blank cancel.g

      I found the mistake. It was the slicer. I accidentally swapped relative and absolute extrusion. As a result, the skirt was still printed and nothing came out of the nozzle during the actual printing

      posted in Beta Firmware
      Heartleander81undefined
      Heartleander81
    • RE: InputShaping Plugin shows only zeros with Toolboard 1lc

      @mfs12 20_2021-10-08_12.32.09.csv

      posted in Plugins for DWC and DSF
      Heartleander81undefined
      Heartleander81
    • RE: Issues with pressure advance since RRF 3.4

      @Argo

      3-3-0Toolboard.jpg
      3.3.0 PA 0.045 Extruder onToolboard
      3-3-0Mainboard.jpg
      3.3.0 PA 0.045 Extruder on Mainboard
      3-4-4TooboardIS.jpg
      3.4.4 PA 0.045 Extruder on Toolboard with IS
      3-4-4Toolboard.jpg
      3.4.4 PA 0.045 Extruder on Toolboard without IS

      3.4.4 Extruder on Mainboard with IS and without IS look the same

      Printed clockwise.
      Outer walls, inner walls, bottom layer and top layer all at 200mm/s.
      First layer with 90mm/s .
      The part is 2mm high with the dimensions 40x40mm.
      Layer height is 0.2mm.

      ; Drive direktion
      M569 P0.1 S0 D2 H20 V2000 				; X physical drive 0.1 goes backwards
      M569 P0.2 S0 D2 H20 V2000 				; Y physical drive 0.2 goes backwards
      M569 P0.0 S1 D2 							; Z1 physical drive 0.0 goes forwards
      M569 P0.4 S1 D2 							; Z2 physical drive 0.4 goes forwards
      M569 P0.3 S1 D2							; Z3 physical drive 0.3 goes forwards
      M569 P0.5 S0 D2 							; (free) physical drive 0.5 goes forwards
      M569 P20.0 S1 D2						; E physical drive 0.0 Driver0 tool goard goes forwards
      
      ; Motor mapping and steps per mm
      M584 X0.1 Y0.2 Z0.0:0.4:0.3 E20.0			; set drivers mapping
      M350 X16 Y16 Z16 I1						; configure microstepping 1/16 with interpolation
      M350 E16								; configure microstepping 1/16
      M92 X80.40 Y80.40 Z800.00 E705.485		; set steps per mm
      
      ; Drive currents
      M906 X1300 Y1300 Z950 E900 				; set motor currents (mA)
      M906 I80								; motor idle factor in per cent
      M84 S120 								; set idle timeout
      
      ; Acceleration and speed
      M566 X1800.00 Y1800.00 Z90.00 E3000.00 P1	; set maximum instantaneous speed changes (mm/min)
      M203 X30000.00 Y30000.00 Z900.00 E15000.00	; set maximum speeds (mm/min)
      M201 X6000.00 Y6000.00 Z100.00 E1800.00		; set accelerations (mm/s^2)
      M201.1 Z40.00								; Homimg smooth ACC
      
      
      ; Accelerometer
      M955 P20.0 I10 S1344 R10			; R12 Accelerometer 20:0 type LIS3DH with orientation 10 samples at 1344Hz with 10-bit resolution
      
      ; PA, IS
      ; At config-override.g
      
      
      posted in General Discussion
      Heartleander81undefined
      Heartleander81

    Latest posts made by Heartleander81

    • RE: Issues with pressure advance since RRF 3.4

      @Argo ok. Nice test from him. I find for my Hevort 0.02 smooth time and 0.044 PA. Worked nice. I hope my Info can help Duet.

      posted in General Discussion
      Heartleander81undefined
      Heartleander81
    • RE: Issues with pressure advance since RRF 3.4

      @Argo said in Issues with pressure advance since RRF 3.4:

      So altering the smooth time value did improve your corners and PA alone did not?

      PA alone didn't make the whole corner look nice. See the picture with the corner sticking out in the direction of travel. Only with the change of smooth time and renewed PA, which was then higher, did the corners become so clean.

      posted in General Discussion
      Heartleander81undefined
      Heartleander81
    • RE: Issues with pressure advance since RRF 3.4

      @dc42
      @Phaedrux

      I couldn't find any differences between 3.3 and 3.4.x, but I still have a picture of a test where the corners became nice with PA. As now with klipper. The Artikel from sebkritel is that who I read.

      posted in General Discussion
      Heartleander81undefined
      Heartleander81
    • RE: Issues with pressure advance since RRF 3.4

      @R4ffers oh yes.

      @dc42 is there also something like pressure advance smooth time under RRF? A few clippers have the problem with the high smooth time, but those who have problems are mostly DirectDrive extruder users. Maybe that's an approach you can follow.

      posted in General Discussion
      Heartleander81undefined
      Heartleander81
    • RE: Issues with pressure advance since RRF 3.4

      Update on my conversion to Klipper.
      At first the corners didn't look any better than with RRF until I came across a post today that refers to extruder smooth time.
      The standard is with Klipper 0.04, which I also use.
      Switched to 0.01 and the corners look awesome.
      In the article it was said that some extruders can not cope with the smooth time and then you have to get smaller. see my pictures.

      20221121_171555.jpg

      With smooth time 0.04

      20221128_153229.jpg 20221128_153233.jpg 20221128_153236.jpg

      With smooth time 0.01

      posted in General Discussion
      Heartleander81undefined
      Heartleander81
    • RE: Duet3 6HC Sense resitor

      @dc42 Many Thanks. Unfortunately, I'm not an electrician and can't read anything out of the schematic. If it were a blueprint of machines I could do that 🙂

      posted in General Discussion
      Heartleander81undefined
      Heartleander81
    • Duet3 6HC Sense resitor

      Hi
      Which Sens resistor value is set in the RepRap firmware for the TMC5160?

      posted in General Discussion
      Heartleander81undefined
      Heartleander81
    • RE: Issues with pressure advance since RRF 3.4

      @Argo

      I will only use it as an emergency backup. Sure if RRF fits again I'll switch back, I think. I'm already a fan of Duet.
      But to test whether my hardware fits, I'll try Klippers. The last parts will arrive in the days for the test with me.

      posted in General Discussion
      Heartleander81undefined
      Heartleander81
    • RE: Issues with pressure advance since RRF 3.4

      @Phaedrux

      Yes, definitely.
      If I increase or decrease the extruder pressure, I can influence whether there is more or less overshoot. But I can't get rid of it completely.

      posted in General Discussion
      Heartleander81undefined
      Heartleander81
    • RE: Issues with pressure advance since RRF 3.4

      @gloomyandy no, on Duet 3 6hc.

      I think that not only z but all axles brake harder. But I'll record it and open another topic and ask if Duet wanted it that way.

      posted in General Discussion
      Heartleander81undefined
      Heartleander81