After updating to 3.4.0beta2: faulty heater 1, -273.1C.

dc42

@jbarros @CadetC @pixelpieper does any of you live in UK?

jbarros

@dc42 said in After updating to 3.4.0beta2: faulty heater 1, -273.1C.:

@jbarros @CadetC @pixelpieper does any of you live in UK?

If this were an usual year I'd say we were a British colony at this time of the year but alas no, I live in Portugal

PS: I have a close relationship with one of your partners here, let me know if you want me to send you something through them (B2B shipping).

CadetC

@dc42 said in After updating to 3.4.0beta2: faulty heater 1, -273.1C.:

@jbarros @CadetC @pixelpieper does any of you live in UK?

Unfortunately I don't live in the UK, in my case it's Poland

pixelpieper

@dc42 sorry, I am in Switzerland...

Serge

Living in France.

CadetC

@dc42
So what do you think? Are our problems caused by software bugs or could it be a hardware problem? What's the prognosis?
Should I return my toolboard as faulty under warranty? Or is there a chance that it will work as it should?

dc42

@cadetc I hope to find time to look into this again tomorrow.

Sotidii

@dc42
m122 b121 p1007 a {0x4200442c}
Address 0x00000000 value 0x20008000

m122 b121 p1007 a {0x806020}
Address 0x00000000 value 0x20008000

dc42

@sotidii said in After updating to 3.4.0beta2: faulty heater 1, -273.1C.:

@dc42
m122 b121 p1007 a {0x4200442c}
Address 0x00000000 value 0x20008000

m122 b121 p1007 a {0x806020}
Address 0x00000000 value 0x20008000

Please run those commands again, without a space between 'a' and '{'.

Sotidii

@dc42
m122 b121 p1007 a{0x806020}
Address 0x00806020 value 0x19147fbe
m122 b121 p1007 a{0x4200442c}
Address 0x4200442c value 0x00000607

dc42

@sotidii @CadetC @pixelpieper @Serge thanks for your patience.

I have tested the new firmware on 9 tool boards and I don't get a problem reading temperatures on any of them. So I would ask you for some more help. I will apply the changes made to the new tool board firmware a few at a time on top of version 3.3 in order to pin down which change introduced the problem.

I have put new tool board firmware at https://www.dropbox.com/sh/heg82sqvhpqb670/AAARGaD-zLptgnHj-PiqiwQBa?dl=0. Please can you try installing this firmware on your tool boards and let me know whether the temperature readings are OK or not. It identifies itself as version 3.3+test1.

CadetC

@dc42
RRF3.4b2 on Duet3
Toolboard v 1.1

m122 b121
Diagnostics for board 121:
Duet TOOL1LC firmware version 3.3 (2021-06-15 16:12:58)
Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)

After toolboard firmware change
RRF3.4b2 on Duet3
Toolboard v 1.1

unM122 B121
Diagnostics for board 121:
Duet TOOL1LC firmware version 3.3+test1 (2021-08-20 16:51:53)
Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)

I think it's fine

Sotidii

@dc42
29=29 OK!

jbarros

@dc42
My temperature is ok with this version.

dc42

Thanks, all! Please can you now try the firmware file Duet3Firmware_TOOL1LC_test2.bin at https://www.dropbox.com/sh/heg82sqvhpqb670/AAARGaD-zLptgnHj-PiqiwQBa?dl=0.

Sotidii

@dc42
29=29 Ok

jbarros

@dc42
Temps good on test2

dc42

Thanks again! Please try firmware Duet3Firmware_TOOL1LC_test3.bin at https://www.dropbox.com/sh/heg82sqvhpqb670/AAARGaD-zLptgnHj-PiqiwQBa?dl=0. If the temperature readings are OK, please use M115 B<can address> to confirm that the firmware installed on the tool board is the test3 version.

jbarros

@dc42

Temps good.
I always check the firmware version but here it is:

Duet TOOL1LC firmware version 3.3+test3 (2021-08-21 11:42:11)
Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)

dc42

@jbarros thanks! Please try test4 at the same location.