Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. CadetC
    • Profile
    • Following 0
    • Followers 0
    • Topics 2
    • Posts 52
    • Best 3
    • Controversial 1
    • Groups 0

    CadetC

    @CadetC

    4
    Reputation
    7
    Profile views
    52
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    CadetC Unfollow Follow

    Best posts made by CadetC

    • RE: InputShaping-Plugin-0.1.0-rc6 released

      @mfs12
      Look like we need rc7 😉
      After installing 3.4b3 rc6 no longer works.

      posted in Plugins for DWC and DSF
      CadetCundefined
      CadetC
    • RE: RRF 3.4b3 - bed heater fault

      @phaedrux said in RRF 3.4b3 - bed heater fault:

      Can you give us some details about the bed and heater?

      Bed is made out of 8 mm aluminum plate with dimensions 340X340
      Heating element - 300X300 - 220V, 750W Kenovo connected via SSR

      Starting with RRF 3.2 I had all versions installed, including betas - it was only with RRF3.4b3 that this problem occurred

      my bed config from config.g

      M308 S0 P"temp0" Y"thermistor" T100000 B4138 A"Bed"      ; configure sensor 0 as thermistor on pin temp0
      M950 H0 C"out0" T0                                   ; create bed heater output on out0 and map it to sensor 0
      M307 H0 B0 S1.00                                     ; disable bang-bang mode for the bed heater and set PWM limit
      M140 H0                                              ; map heated bed to heater 0
      M143 H0 S130                                         ; set temperature limit for heater 0 to 130C
      
      
      posted in Beta Firmware
      CadetCundefined
      CadetC
    • RE: Layer times

      @imsother
      @Phaedrux
      I had a similar problem, but I use PrusaSlicer . Everything came back to normal after adding ;LAYER:[layer_num] to the custom gcode tab under the "before layer change g-code" section in printer setting in PrusaSlicer

      posted in Duet Web Control
      CadetCundefined
      CadetC
    • RE: Toolboard with built in accelometer +SBC - failed promise

      @becky9 said in Toolboard with built in accelometer +SBC - failed promise:

      No promises have been broken, v3.4 has not been released yet. The release of all beta software is taken as read that its not the released version and is a work in progress. I think your expectations and understanding is flawed.

      Are you a member of the develepor team.- If not, then the post was definitely not directed at you. If someone writes that the problem has been solved - "I've got a fix ready for M956, too." and that he plans to release an update in two days - "Yes, I hope I can do another prerelease on Thursday as I won't be available tomorrow." (these are forum responses to my questions given over a week ago ) then how should I treat such information????

      posted in General Discussion
      CadetCundefined
      CadetC

    Latest posts made by CadetC

    • RE: Layer times

      @imsother
      @Phaedrux
      I had a similar problem, but I use PrusaSlicer . Everything came back to normal after adding ;LAYER:[layer_num] to the custom gcode tab under the "before layer change g-code" section in printer setting in PrusaSlicer

      posted in Duet Web Control
      CadetCundefined
      CadetC
    • RE: RRF 3.4b3 - bed heater fault

      @dc42
      Today I checked again how this issue looks like - when heating up to 110C I had to delete fault once, then everything was OK.
      After about 30 minutes temperature quite stable, small fluctuations +0.1, -0.1 degrees .
      After the temperature of the table stabilized (with small deviations as above) the result of M573 varied from 0.226 to 0.242 - I checked it for about 15 minutes

      30.08.2021, 17:18:38	M307 H0
      Heater 0 model: heating rate 0.858, cooling time constant 275.9, dead time 4.18, max PWM 1.00, calibration voltage 24.0, mode PID
      Computed PID parameters: setpoint change: P49.8, I1.466, D145.6, load change: P49.8, I3.664, D145.6
      30.08.2021, 17:17:49	M573 p0undefined
      
      posted in Beta Firmware
      CadetCundefined
      CadetC
    • RE: RRF 3.4b3 - bed heater fault

      @dc42 said in RRF 3.4b3 - bed heater fault:

      @siam thanks. If the M573 reading is not stable, is the temperature oscillating a little? If so, increase the M307 D parameter until it is stable. You can do this while the heater is hot.

      the temperature after reaching the desired 110 degrees is a little unstable, it fluctuates within +0.3, -0.3 degrees
      I tried to change parameter D, but I don't know by what values I can change it - I changed it by 0.1 to the value 4.80 with no visible improvement.
      Here are the readings taken about an hour after setting the bed temperature

      M573 results

      .08.2021, 16:03:22	m573 P0
      Average heater 0 PWM: 0.196
      28.08.2021, 16:03:16	m573 P0
      Average heater 0 PWM: 0.165
      28.08.2021, 16:03:15	m573 P0
      Average heater 0 PWM: 0.163
      28.08.2021, 16:03:14	m573 P0
      Average heater 0 PWM: 0.178
      28.08.2021, 16:03:12	m573 P0
      Average heater 0 PWM: 0.213
      28.08.2021, 16:02:57	m573 P0
      Average heater 0 PWM: 0.256
      

      Ambient temperature 20C
      Bed temperature 110C

      M307 H0

      8.08.2021, 16:00:46	M307 H0
      Heater 0 model: heating rate 0.858, cooling time constant 275.9, dead time 4.18, max PWM 1.00, calibration voltage 24.0, mode PID
      Computed PID parameters:
       setpoint change: P49.8, I1.466, D145.6, load change: P49.8, I3.664, D145.6
      
      posted in Beta Firmware
      CadetCundefined
      CadetC
    • RE: RRF 3.4b3 - bed heater fault

      @phaedrux said in RRF 3.4b3 - bed heater fault:

      Can you give us some details about the bed and heater?

      Bed is made out of 8 mm aluminum plate with dimensions 340X340
      Heating element - 300X300 - 220V, 750W Kenovo connected via SSR

      Starting with RRF 3.2 I had all versions installed, including betas - it was only with RRF3.4b3 that this problem occurred

      my bed config from config.g

      M308 S0 P"temp0" Y"thermistor" T100000 B4138 A"Bed"      ; configure sensor 0 as thermistor on pin temp0
      M950 H0 C"out0" T0                                   ; create bed heater output on out0 and map it to sensor 0
      M307 H0 B0 S1.00                                     ; disable bang-bang mode for the bed heater and set PWM limit
      M140 H0                                              ; map heated bed to heater 0
      M143 H0 S130                                         ; set temperature limit for heater 0 to 130C
      
      
      posted in Beta Firmware
      CadetCundefined
      CadetC
    • RE: Help for translation needed

      @mfs12
      I can help with polish translation

      posted in General Discussion
      CadetCundefined
      CadetC
    • RRF 3.4b3 - bed heater fault

      after installing 3.4b3 i have problem with table heating - of course pid tuning done. Previously there were no such problems. If I set the temperature of the table at 110C (temperature at which I print) in order to heat up the table first and run ABL, I have to delete the fault twice before the table reaches the temperature and maintains it - after reaching the set temperature it is stable.

      27.08.2021, 12:58:22	Error: Heater 0 fault: temperature rising much more slowly than the expected 0.6°C/sec
      

      my M307 after pid tuned

      M307 H0 B0 R0.858 C275.9 D4.18 S1.00 V24.0
      
      posted in Beta Firmware
      CadetCundefined
      CadetC
    • RE: mid print stall RRF 3.4B2

      @nuramori
      What motors do you use for xy, ? I am surprised at the low current you have set for them. Another thing, and here I ask because I can not find any info on M915(stallguard) and T1 parameter - what is it for?

      posted in Beta Firmware
      CadetCundefined
      CadetC
    • RE: InputShaping-Plugin-0.1.0-rc6 released

      @mfs12
      Look like we need rc7 😉
      After installing 3.4b3 rc6 no longer works.

      posted in Plugins for DWC and DSF
      CadetCundefined
      CadetC
    • RE: After updating to 3.4.0beta2: faulty heater 1, -273.1C.

      @dc42
      there is definitely a difference between firmware 3.4b2 and 3.4b2+2
      below is a screen with temperature reading for 3.4b2 and below for 3.4b2+2 -

      comparison made just now

      m122 b121.0
      Diagnostics for board 121:
      Duet TOOL1LC firmware version 3.4.0beta2 (2021-08-03 10:00:09)
      Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)
      

      Przechwytywanie.JPG

      m122 b121
      Diagnostics for board 121:
      Duet TOOL1LC firmware version 3.4.0beta2+2 (2021-08-21 14:16:34)
      Bootloader ID: SAMC21 bootloader version 2.3 (2021-01-26b1)
      

      Przechwytywanie.JPG

      But all in all, the most important thing is that it's OK now,

      Thanks

      posted in Beta Firmware
      CadetCundefined
      CadetC
    • RE: After updating to 3.4.0beta2: faulty heater 1, -273.1C.

      @dc42

      m122 b121.0
      Diagnostics for board 121:
      Duet TOOL1LC firmware version 3.4.0beta2+2 (2021-08-21 14:16:34)
      
      posted in Beta Firmware
      CadetCundefined
      CadetC