• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

homing dual z with independant motors

Scheduled Pinned Locked Moved
General Discussion
3
36
1.5k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    Monkey68
    last edited by 13 Sept 2021, 04:11

    duet 2wifi 1.03 ,3.3 fw
    cartesian printer
    dual z motors connected to z +e1
    dual z endstops connected to z +e1
    probe connected to probe
    can home x, can home y.
    z tries to home, it moves to the upper switches and triggers the switches as indicated by the leds on the board but the motors keep trying to go and it just sits there and bounces on the stops, the e1 light flashes.

    1 Reply Last reply Reply Quote 0
    • undefined
      Monkey68
      last edited by 13 Sept 2021, 04:13

      ; Drives
      M569 P0.0 S1 ; physical drive 0 goes forwards
      M569 P0.1 S1 ; physical drive 1 goes forwards
      M569 P0.2 S0 ; physical drive 2 goes backwards
      M569 P0.3 S1 ; physical drive 3 goes forwards
      M569 P0.4 S0 ; physical drive 4 goes backwards

      ;M584 X0 Y1 Z2 E3 ; set drive mapping
      M584 X0.0 Y0.1 Z0.2:0.4 E0.3 ;two Z motors connected to driver outputs Z and E1
      M671 X-18:224 Y112.5:112.5 S0.5 ; leadscrews at left (connected to Z) and right (connected to E1) of X axis
      M350 X16 Y16 Z16:16 E16 I1 ; configure microstepping with interpolation
      M92 X80.00 Y80.00 Z400.00:400.00 E143.2 ; set steps per mm
      M566 X800.00 Y800.00 Z1000.00:1000.00 E3600.00 ; set maximum instantaneous speed changes (mm/min)
      M203 X9600.00 Y9600.00 Z1000.00:1000.00 E6000.00 ; set maximum speeds (mm/min)
      M201 X1000.00 Y1000.00 Z600.00:600.00 E2000.00 ; set accelerations (mm/s^2)
      M906 X1250 Y1300 Z1250:1250 E1250 I30 ; set motor currents (mA) and motor idle factor in per cent
      M572 D0 S0.002 ;set pressure advance
      M84 S30 ; Set idle timeout

      ; Axis Limits
      M208 X-27 Y-35 Z0 S1 ; set axis minima
      M208 X250 Y225 Z300 S0 ; set axis maxima
      ;M208 X-5:205 Y0:200 ; X carriage moves from -5 to 205, Y bed goes from 0 to 200

      ; Endstops ```; Snnn 1 = switch-type (eg microswitch) endstop input, 2 = Z probe (when used to home an axis other than Z), 3 = single motor load detection, 4 = multiple motor load detection
      M574 X1 S1 P"!xstop" ; configure active-high endstop for low end on X via pin xstop
      M574 Y1 S1 P"!ystop" ; configure active-high endstop for low end on Y via pin ystop
      M574 Z2 S1 P"!zstop" ; configure active-high endstops for low end on Z via pins zstop and e1stop
      M574 E12 S1 P"!e1stop"
      ;M574 Z2 S1 P"!zstop+!e1stop" ; configure active-high endstops for high end on Z via pins zstop and e1stop

      ; Filament Sensing
      M591 D0 P1 C"!e0stop" S1 ; filament monitor connected to E0 endstop

      ; Z-Probe
      M558 P1 C"zprobe.in" H3 F600 T6000 A3 S0.03 ; set Z probe type to unmodulated and the dive height + speeds
      G31 P1000 X25 Y14 Z1.50 ; set Z probe trigger value, offset and trigger height
      ;M557 X45:265 Y45:265 S110 ; define mesh grid glass bed plate
      M557 X45:245 Y45:220 S87.5 ; define mesh grid prusa bed plate

      ; Heaters
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 C0 R4700 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      ;M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
      M307 H0 A90.0 C700.0 D10.0 S1.00 V0.0 B1
      M140 H0 ; map heated bed to heater 0
      M143 H0 S150 ; set temperature limit for heater 0 to 150C
      M308 S1 P"e0temp" Y"thermistor" T500000 B4723 C1.196220e-7 ; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      ;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
      ;M307 H1 A340.0 C140.0 D5.5 S1.00 V0.0 B0
      M307 H1 A388.5 C88.1 D2.4 S1.00 V24.2 B0
      M143 H1 S500 ; set temperature limit for heater 1 to 500C

      ; Fans
      M950 F0 C"^fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
      M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
      M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
      M950 F2 C"duex.fan3" Q500 ; create fan 2 on pin duex.fan3 and set its frequency
      M106 P2 S1 H1 T45 ; set fan 2 value. Thermostatic control is turned on
      M950 F3 C"duex.fan4" Q500 ; create fan 3 on pin duex.fan4 and set its frequency
      M106 P3 S1 H1 T45 ; set fan 3 value. Thermostatic control is turned on

      ; Tools
      M563 P0 S"Copper Head" D0 H1 F0 ; define tool 0
      G10 P0 X0 Y0 Z0:0 ; set tool 0 axis offsets
      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

      ; Custom settings are not defined

      ; Miscellaneous
      T0 ; select first tool
      M501

      undefined undefined 2 Replies Last reply 13 Sept 2021, 06:59 Reply Quote 0
      • undefined
        Monkey68
        last edited by 13 Sept 2021, 04:14

        ; homez.g
        ; called to home the Z axis
        ; generated by RepRapFirmware Configuration Tool v3.3.2 on Wed Sep 08 2021 20:07:17 GMT+1200 (New Zealand Standard Time)

        G90 ; absolute positioning
        G1 X125 Y105 F6000 ; go to probe point
        G91 ; relative positioning
        G1 H2 Z305 E1305 F1800 ; lift Z relative to current position
        G1 H1 Z-5 E1-5 F6000
        G1 H2 Z305 E1305 F360
        G90
        G30 ; home Z by probing the bed

        1 Reply Last reply Reply Quote 0
        • undefined
          Monkey68
          last edited by 13 Sept 2021, 04:16

          ; homeall.g
          ; called to home all axes
          ;
          ; generated by RepRapFirmware Configuration Tool v3.3.1 on Thu Aug 26 2021 19:02:13 GMT+1200 (New Zealand Standard Time)
          ;G91 ; relative positioning
          ;G1 H2 Z5 F6000 ; lift Z relative to current position

          ;G1 H1 X-305 Y-305 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
          ;G1 X5 Y5 F6000 ; go back a few mm
          ;G1 H1 X-305 Y-305 F360 ; move slowly to X and Y axis endstops once more (second pass)
          ;G90 ; absolute positioning
          ;G1 X125 Y105 F6000
          ;G30

          ; Uncomment the following lines to lift Z after probing
          ;G91 ; relative positioning
          ;G1 Z5.5 F360 ; lift Z relative to current position
          ;G90 ; absolute positioning

          G91 ; relative positioning
          G1 H2 Z5 F6000 ; lift Z relative to current position
          G1 H1 X-282 Y265 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
          G1 H2 X5 Y-5 F6000 ; go back a few mm
          G1 H1 X-282 Y265 F360 ; move slowly to X and Y axis endstops once more (second pass)
          G1 H1 Z305 F360 ; move Z up stopping at the endstop
          G90 ; absolute positioning
          G92 Z300 ; set Z position to axis maximum (you may want to adjust this)

          1 Reply Last reply Reply Quote 0
          • undefined
            o_lampe @Monkey68
            last edited by o_lampe 13 Sept 2021, 06:59

            Once you've defined the dual Z axis like that: (modified quotation)
            @monkey68 said in homing dual z with independant motors:

            M584 X0.0 Y0.1 Z0.2:0.4 E0.3 ;two Z motors connected to driver outputs Z and E1
            M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
            M92 X80.00 Y80.00 Z400.00 E143.2 ; set steps per mm
            M566 X... Y... Z1000.00 ...; set maximum instantaneous speed changes (mm/min)
            M203 X... Y... Z1000.00 E... ; set maximum speeds (mm/min)
            M201 X... Y... Z600.00 E... ; set accelerations (mm/s^2)
            M906 X... Y... Z1250 E... I30 ; set motor currents (mA) and motor idle factor in per cent
            ...
            ; endstops
            M574 Z2 S1 P"!zstop+!e1stop"

            you must not refer to E1 in the homing files
            @monkey68 said in homing dual z with independant motors:

            ; homez.g
            ; called to home the Z axis
            ; generated by RepRapFirmware Configuration Tool v3.3.2 on Wed Sep 08 2021 20:07:17 GMT+1200 (New Zealand Standard Time)
            G90 ; absolute positioning
            G1 X125 Y105 F6000 ; go to probe point
            G91 ; relative positioning
            G1 H2 Z305 F1800 ; lift Z relative to current position
            G1 H1 Z-5 F6000
            G1 H2 Z10 F360
            G90
            G30 ; home Z by probing the bed

            undefined 1 Reply Last reply 13 Sept 2021, 07:54 Reply Quote 0
            • undefined
              Monkey68 @o_lampe
              last edited by 13 Sept 2021, 07:54

              @o_lampe ok thank you, I have tried that and it makes no difference

              1 Reply Last reply Reply Quote 0
              • undefined
                Phaedrux Moderator @Monkey68
                last edited by 13 Sept 2021, 18:10

                @monkey68 said in homing dual z with independant motors:

                M574 E12 S1 P"!e1stop"
                ;M574 Z2 S1 P"!zstop+!e1stop" ; configure active-high endstops for high end on Z via pins zstop and e1stop

                The first line is incorrect. The second line is correct.

                Z1000.00:1000.00

                Remove all the duplicated values for Z from config.g

                Please share the results of sending M122 and M98 P"config.g"

                Z-Bot CoreXY Build | Thingiverse Profile

                undefined 1 Reply Last reply 13 Sept 2021, 23:24 Reply Quote 0
                • undefined
                  Monkey68 @Phaedrux
                  last edited by 13 Sept 2021, 23:24

                  @phaedrux said in homing dual z with independant motors:

                  M98 P"config.g"

                  M98 P"config.g"
                  HTTP is enabled on port 80
                  FTP is disabled
                  TELNET is disabled
                  Endstop configuration:
                  X: low end switch connected to pin !xstop
                  Y: low end switch connected to pin !ystop
                  Z: high end switch connected to pin !zstopWarning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 442C

                  undefined undefined 2 Replies Last reply 13 Sept 2021, 23:25 Reply Quote 0
                  • undefined
                    Monkey68 @Monkey68
                    last edited by 13 Sept 2021, 23:25

                    @monkey68 ; Network
                    M552 S1 ; enable network
                    M586 P0 S1 ; enable HTTP
                    M586 P1 S0 ; disable FTP
                    M586 P2 S0 ; disable Telnet

                    ; Drives
                    M569 P0.0 S1 ; physical drive 0 goes forwards
                    M569 P0.1 S1 ; physical drive 1 goes forwards
                    M569 P0.2 S0 ; physical drive 2 goes backwards
                    M569 P0.3 S1 ; physical drive 3 goes forwards
                    M569 P0.4 S0 ; physical drive 4 goes backwards

                    ;M584 X0 Y1 Z2 E3 ; set drive mapping
                    M584 X0.0 Y0.1 Z0.2:0.4 E0.3 ;two Z motors connected to driver outputs Z and E1
                    M671 X-18:224 Y112.5:112.5 S0.5 ; leadscrews at left (connected to Z) and right (connected to E1) of X axis
                    ;M350 X16 Y16 Z16:16 E16 I1 ; configure microstepping with interpolation
                    M350 X16 Y16 Z16 E16 E116 I1
                    ;M92 X80.00 Y80.00 Z400.00:400.00 E143.2 ; set steps per mm
                    M92 X80.00 Y80.00 Z400.00 E143.2 E1400
                    ;M566 X800.00 Y800.00 Z1000.00:1000.00 E3600.00 ; set maximum instantaneous speed changes (mm/min)
                    M566 X800.00 Y800.00 Z1000.00 E3600.00 E11000
                    ;M203 X9600.00 Y9600.00 Z1000.00:1000.00 E6000.00 ; set maximum speeds (mm/min)
                    M203 X9600.00 Y9600.00 Z1000.00 E6000.00 E11000
                    ;M201 X1000.00 Y1000.00 Z600.00:600.00 E2000.00 ; set accelerations (mm/s^2)
                    M201 X1000.00 Y1000.00 Z600.00 E2000.00 E1600
                    ;M906 X1250 Y1300 Z1250:1250 E1250 I30 ; set motor currents (mA) and motor idle factor in per cent
                    M906 X1250 Y1300 Z1250 E1250 E11250 I30
                    M572 D0 S0.002 ;set pressure advance
                    M84 S30 ; Set idle timeout

                    ; Axis Limits
                    M208 X-27 Y-35 Z0 S1 ; set axis minima
                    M208 X250 Y225 Z300 S0 ; set axis maxima
                    ;M208 X-5:205 Y0:200 ; X carriage moves from -5 to 205, Y bed goes from 0 to 200

                    ; Endstops ```; Snnn 1 = switch-type (eg microswitch) endstop input, 2 = Z probe (when used to home an axis other than Z), 3 = single motor load detection, 4 = multiple motor load detection
                    M574 X1 S1 P"!xstop" ; configure active-high endstop for low end on X via pin xstop
                    M574 Y1 S1 P"!ystop" ; configure active-high endstop for low end on Y via pin ystop
                    M574 Z2 S1 P"!zstop" ; configure active-high endstops for low end on Z via pins zstop and e1stop
                    M574 E12 S1 P"!e1stop"
                    ;M574 Z2 S1 P"!zstop+!e1stop" ; configure active-high endstops for high end on Z via pins zstop and e1stop

                    ; Filament Sensing
                    M591 D0 P1 C"!e0stop" S1 ; filament monitor connected to E0 endstop

                    ; Z-Probe
                    M558 P1 C"zprobe.in" H3 F600 T6000 A3 S0.03 ; set Z probe type to unmodulated and the dive height + speeds
                    G31 P1000 X25 Y14 Z1.50 ; set Z probe trigger value, offset and trigger height
                    ;M557 X45:265 Y45:265 S110 ; define mesh grid glass bed plate
                    M557 X45:245 Y45:220 S87.5 ; define mesh grid prusa bed plate

                    ; Heaters
                    M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 C0 R4700 ; configure sensor 0 as thermistor on pin bedtemp
                    M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
                    ;M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
                    M307 H0 A90.0 C700.0 D10.0 S1.00 V0.0 B1
                    M140 H0 ; map heated bed to heater 0
                    M143 H0 S150 ; set temperature limit for heater 0 to 150C
                    M308 S1 P"e0temp" Y"thermistor" T500000 B4723 C1.196220e-7 ; configure sensor 1 as thermistor on pin e0temp
                    M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
                    ;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                    ;M307 H1 A340.0 C140.0 D5.5 S1.00 V0.0 B0
                    M307 H1 A388.5 C88.1 D2.4 S1.00 V24.2 B0
                    M143 H1 S500 ; set temperature limit for heater 1 to 500C

                    ; Fans
                    M950 F0 C"^fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
                    M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
                    M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
                    M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
                    M950 F2 C"duex.fan3" Q500 ; create fan 2 on pin duex.fan3 and set its frequency
                    M106 P2 S1 H1 T45 ; set fan 2 value. Thermostatic control is turned on
                    M950 F3 C"duex.fan4" Q500 ; create fan 3 on pin duex.fan4 and set its frequency
                    M106 P3 S1 H1 T45 ; set fan 3 value. Thermostatic control is turned on

                    ; Tools
                    M563 P0 S"Copper Head" D0 H1 F0 ; define tool 0
                    G10 P0 X0 Y0 Z0:0 ; set tool 0 axis offsets
                    G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                    ; Custom settings are not defined

                    ; Miscellaneous
                    T0 ; select first tool
                    M501

                    undefined undefined 3 Replies Last reply 13 Sept 2021, 23:29 Reply Quote 0
                    • undefined
                      Monkey68 @Monkey68
                      last edited by 13 Sept 2021, 23:29

                      @monkey68 the heater 0 is room temperature as in its not hot 😉

                      1 Reply Last reply Reply Quote 0
                      • undefined
                        Phaedrux Moderator @Monkey68
                        last edited by 14 Sept 2021, 03:59

                        @monkey68 said in homing dual z with independant motors:

                        Endstop configuration:
                        X: low end switch connected to pin !xstop
                        Y: low end switch connected to pin !ystop
                        Z: high end switch connected to pin !zstop

                        Is this being reported from when you send M98 P"config.g"?

                        @monkey68 said in homing dual z with independant motors:

                        @monkey68 the heater 0 is room temperature as in its not hot 😉

                        If you're referring to the heater 0 temp warning it's just telling you what the predicted max temp could be in a runaway situation.

                        @phaedrux said in homing dual z with independant motors:

                        Please share the results of sending M122

                        Can we get this please?

                        @monkey68 said in homing dual z with independant motors:

                        M574 E12 S1 P"!e1stop"

                        What are you trying to do with this command?

                        @monkey68 said in homing dual z with independant motors:

                        M350 X16 Y16 Z16 E16 E116 I1
                        ;M92 X80.00 Y80.00 Z400.00:400.00 E143.2 ; set steps per mm
                        M92 X80.00 Y80.00 Z400.00 E143.2 E1400

                        You've got E values listed twice in some of your commands. Why?
                        Do you have multiple extruders? If so the correct format is E###:### just like you had before for the Z axis. That format is only correct for extruders.

                        Z-Bot CoreXY Build | Thingiverse Profile

                        undefined 3 Replies Last reply 14 Sept 2021, 04:07 Reply Quote 0
                        • undefined
                          Monkey68 @Phaedrux
                          last edited by 14 Sept 2021, 04:07

                          @phaedrux 14/09/2021, 16:06:14 m122
                          === Diagnostics ===
                          RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later + DueX5
                          Board ID: 08DGM-9568A-F23SD-6JTDG-3SN6P-1UR7H
                          Used output buffers: 3 of 24 (15 max)
                          === RTOS ===
                          Static ram: 23876
                          Dynamic ram: 76012 of which 0 recycled
                          Never used RAM 14528, free system stack 182 words
                          Tasks: NETWORK(ready,78.7%,244) HEAT(delaying,0.2%,314) Move(notifyWait,0.4%,340) DUEX(notifyWait,0.0%,24) MAIN(running,20.6%,441) IDLE(ready,0.1%,29), total 100.0%
                          Owned mutexes:
                          === Platform ===
                          Last reset 04:38:52 ago, cause: software
                          Last software reset at 2021-09-14 11:27, reason: User, GCodes spinning, available RAM 11320, slot 1
                          Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
                          Error status: 0x00
                          Step timer max interval 0
                          MCU temperature: min 36.4, current 41.9, max 42.4
                          Supply voltage: min 24.1, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
                          Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
                          Driver 0: position 0, standstill, SG min/max not available
                          Driver 1: position 0, standstill, SG min/max not available
                          Driver 2: position 0, standstill, SG min/max not available
                          Driver 3: position 0, standstill, SG min/max not available
                          Driver 4: position 0, standstill, SG min/max not available
                          Driver 5: position 0, standstill, SG min/max not available
                          Driver 6: position 0, standstill, SG min/max not available
                          Driver 7: position 0, standstill, SG min/max not available
                          Driver 8: position 0, standstill, SG min/max not available
                          Driver 9: position 0, standstill, SG min/max not available
                          Driver 10: position 0
                          Driver 11: position 0
                          Date/time: 2021-09-14 16:06:12
                          Cache data hit count 4294967295
                          Slowest loop: 6.17ms; fastest: 0.17ms
                          I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
                          === Storage ===
                          Free file entries: 10
                          SD card 0 detected, interface speed: 20.0MBytes/sec
                          SD card longest read time 1.3ms, write time 0.0ms, max retries 0
                          === Move ===
                          DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
                          === MainDDARing ===
                          Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
                          === AuxDDARing ===
                          Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
                          === Heat ===
                          Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
                          Heater 1 is on, I-accum = 0.0
                          === GCodes ===
                          Segments left: 0
                          Movement lock held by null
                          HTTP is idle in state(s) 0
                          Telnet is idle in state(s) 0
                          File is idle in state(s) 0
                          USB is idle in state(s) 0
                          Aux is idle in state(s) 0
                          Trigger is idle in state(s) 0
                          Queue is idle in state(s) 0
                          LCD is idle in state(s) 0
                          Daemon is idle in state(s) 0
                          Autopause is idle in state(s) 0
                          Code queue is empty.
                          === Filament sensors ===
                          Extruder 0 sensor: ok
                          === DueX ===
                          Read count 1, 0.00 reads/min
                          === Network ===
                          Slowest loop: 15.58ms; fastest: 0.00ms
                          Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
                          HTTP sessions: 1 of 8

                          • WiFi -
                            Network state is active
                            WiFi module is connected to access point
                            Failed messages: pending 0, notready 0, noresp 0
                            WiFi firmware version 1.26
                            WiFi MAC address 2c:3a:e8:0b:1f:b7
                            WiFi Vcc 3.34, reset reason Turned on by main processor
                            WiFi flash size 4194304, free heap 26920
                            WiFi IP address 192.168.50.251
                            WiFi signal strength -58dBm, mode 802.11n, reconnections 0, sleep mode modem
                            Clock register 00002002
                            Socket states: 4 0 0 0 0 0 0 0
                          undefined 1 Reply Last reply 14 Sept 2021, 04:09 Reply Quote 0
                          • undefined
                            Monkey68 @Monkey68
                            last edited by 14 Sept 2021, 04:09

                            @monkey68 14/09/2021, 16:08:44 M98 P"config.g"
                            HTTP is enabled on port 80
                            FTP is disabled
                            TELNET is disabled
                            Endstop configuration:
                            X: low end switch connected to pin !xstop
                            Y: low end switch connected to pin !ystop
                            Z: high end switch connected to pin !zstopWarning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 442C

                            1 Reply Last reply Reply Quote 0
                            • undefined
                              Phaedrux Moderator @Monkey68
                              last edited by 14 Sept 2021, 04:10

                              @monkey68 said in homing dual z with independant motors:

                              M574 E12 S1 P"!e1stop"

                              Can you remove that line from config.g and send M98 P"config.g" again and see if it still spits out the endstop configuration?

                              Z-Bot CoreXY Build | Thingiverse Profile

                              1 Reply Last reply Reply Quote 0
                              • undefined
                                Monkey68 @Phaedrux
                                last edited by 14 Sept 2021, 04:17

                                @phaedrux ok i will remove them, the motor connected to E1 did not move before just the z and reading throught all of the comments and checking out the how to's which i have come to figure out are out dated and dont apply to the 3 series firmware is really confusing and should be sorted out and then you guys wouldnt be so busy doing the supposed simple stuff that we that are less affluent in the firmware can not work out, it was much simpler when i first got my duet as i could read the guides and copy the needed txt and like magic it just worked, sadly thats not the case anymore. sorry for the rant

                                1 Reply Last reply Reply Quote 0
                                • undefined
                                  Phaedrux Moderator
                                  last edited by 14 Sept 2021, 04:20

                                  The instructions are here for both RRF2 and RRF3.

                                  https://duet3d.dozuki.com/Wiki/Bed_levelling_using_multiple_independent_Z_motors

                                  What guides are you looking at that are out of date?

                                  Z-Bot CoreXY Build | Thingiverse Profile

                                  undefined 1 Reply Last reply 14 Sept 2021, 04:22 Reply Quote 0
                                  • undefined
                                    Monkey68 @Phaedrux
                                    last edited by 14 Sept 2021, 04:22

                                    @phaedrux 14/09/2021, 16:21:37 M98 P"config.g"
                                    HTTP is enabled on port 80
                                    FTP is disabled
                                    TELNET is disabled
                                    Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 442C

                                    1 Reply Last reply Reply Quote 0
                                    • undefined
                                      Phaedrux Moderator @Monkey68
                                      last edited by 14 Sept 2021, 04:26

                                      @monkey68 said in homing dual z with independant motors:

                                      M574 Z2 S1 P"!zstop+!e1stop"

                                      Ok, so now you can uncomment that line, which should be correct.

                                      Now you can test the homing again, but this time click the switches by hand before it reaches them so that you have time to hit the estop if it doesn't stop movement.

                                      You can also check the status of the endstops by sending M119. Check it when the endstops are depressed and again when they are not and see if it reports the state you would expect.

                                      Z-Bot CoreXY Build | Thingiverse Profile

                                      1 Reply Last reply Reply Quote 0
                                      • undefined
                                        Monkey68 @Phaedrux
                                        last edited by 14 Sept 2021, 04:30

                                        @phaedrux M574 E12 S1 P"!e1stop"
                                        following the instructions given in the guides, specifying the stop for the motor and its place on the axis

                                        undefined 1 Reply Last reply 14 Sept 2021, 04:33 Reply Quote 0
                                        • undefined
                                          Phaedrux Moderator
                                          last edited by Phaedrux 14 Sept 2021, 04:31

                                          What guides?

                                          E12 isn't valid in any way.

                                          Z-Bot CoreXY Build | Thingiverse Profile

                                          undefined 1 Reply Last reply 14 Sept 2021, 04:36 Reply Quote 0
                                          9 out of 36
                                          • First post
                                            9/36
                                            Last post
                                          Unless otherwise noted, all forum content is licensed under CC-BY-SA