Ps-on / PS-off Duet3 6HC

Heartleander81

@oozebot yes M80 C"!pson" have I in my config. Must M80 in the config.g?
When I turn the Main switch on then is all ok. All start and the tool board is there.
But when I switch with Software off and then on there is no thermistor there. After M999 is all good.

How make I this with the macro?

I've never worked with macros so I don't know how to do it.

[ Edit ]

I have copy your macro.
I must changes > TO < then work power of but power not.
With M80 in the macro goes the PSU on but the M999 will not be performed.

Without M80 and M80 in the Firmware do the macro nothing from off to on.

Heartleander81

if boards[0].vIn.current < 22

	M291 R"Turn on power" P":-)" S1 T5
        M80
        G4 S1
        M999 ; Soft-reset Mainboard
        ;M999 A1 ; Soft-reset PanelDue

else

	M291 R"Turn off power" P" Zzzz" S1 T5
	M81 S1 ; Power off 24v power supply
	;G4 S1 ; Pause for one second
	;M999 A1 ; Soft-reset PanelDue

That is what I use. I doun't have a PanelDue to time but is the next what I buy

oozeBot

@heartleander81 Awesome! Glad you got it working..

Heartleander81

@oozebot not completed. At power on doun't come M999 AMD the board stand at working

oozeBot

@heartleander81 that's why the M80 is in our config.g..

Heartleander81

@oozebot to time I doun't have M80 in the config.g.
M999 is not executed because the board is busy. The next step would be M999 but it will not be executed

Heartleander81

I think that an M999 cannot be executed by a macro. I commented out all M999 and the macro is running. I added an G4 S5 and then M98 P "config.g" after the M80, which works. I only get 2 error messages that read as follows.

Warning: Board 20 does not have input handle 3000
Warning: Board 20 does not have input handle 1000

what are the warnings and how can you turn them off?

if boards[0].vIn.current < 22

	M291 R"Turn on power" P":-)" S1 T5
        M80
        G4 S4
        M98 P"config.g"

else

	M291 R"Turn off power" P" Zzzz" S1 T5
	M81 S1 ; Power off 24v power supply

oozeBot

@heartleander81 I just tested with a single line macro that only contains "M999" and it is properly restarting. This is on 3.4b4 but I'm certain it works on 3.3 as well.

Heartleander81

@oozebot i use RFF 3.4b4. Can you test the complet macro without M98 but with M999?

oozeBot

@heartleander81 said in Ps-on / PS-off Duet3 6HC:

@oozebot i use RFF 3.4b4. Can you test the complet macro without M98 but with M999?

I do believe the status becomes busy when M98 is run. I can try to test this soon, but just started a job on the printer I was testing with.

Heartleander81

I have create a single line macro with M999 in it and at my System doun't work it.

DWC say Work and Do nothing. After write in console M999 is all normal

Heartleander81

@oozebot OK. On my system, a Macro with M999 comes busy. With M98 P "config.g" it runs except for 2 warnings regarding the toolboard

Sorry in the last Post i doun't mean status work, I mean status busy. Sorry my english is not the best

XD

oozeBot

@heartleander81 The toolboard will cause a few warnings.. Glad you found a work-around. I'm not sure why M999 isn't working from a macro. It seems to be working fine for us..

Heartleander81

@oozebot Yes, I get 2 warnings when loading the config. It doesn't seem to matter. Will start a test print with it tomorrow. Unfortunately, I don't know why M999 doesn't work for me in the macro.