Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Place to show off PCB Effector assemblies

    Scheduled Pinned Locked Moved
    Smart effector for delta printers
    15
    49
    8.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Hergonowayundefined
      Hergonoway
      last edited by

      For my part I used these blowers fan 24v 404010mm : https://www.aliexpress.com/item/2PCS-Gdstime-40mm-40x10mm-4CM-DC-24V-0-1A-Mini-Turbo-Blower-Cooling-Cooler-Fan-For/32799434002.html

      10.25CFM, 24V works with PWM (without tuning M106, with default frequency F250)

      Delta goes BrrrRRRRrrrrrRRRRrrr

      1 Reply Last reply Reply Quote 0
      • DADIYundefined
        DADIY
        last edited by

        @Hergonoway:

        For my part I used these blowers fan 24v 404010mm : https://www.aliexpress.com/item/2PCS-Gdstime-40mm-40x10mm-4CM-DC-24V-0-1A-Mini-Turbo-Blower-Cooling-Cooler-Fan-For/32799434002.html

        10.25CFM, 24V works with PWM (without tuning M106, with default frequency F250)

        thanks for the link, I've just ordered a couple as for some reason the standard fan+shroud didn't fit my smart effector correctly. I just hope not to get burnt by Ali express again. The bed heater I ordered from there got lost in the post but they favoured the seller so I lost my money.

        1 Reply Last reply Reply Quote 0
        • number40fanundefined
          number40fan
          last edited by

          I ordered two sets as well. I don't currently run 24V, but the time shipping takes, I might get the itch before they show up.

          1 Reply Last reply Reply Quote 0
          • Mikeundefined
            Mike
            last edited by

            Isn't it a lot more convenient to just run the fans from 12V? Sure, you need a step-down converter or a separate 12V PSU, but the choice of fans is so much greater. A DC-DC buck converter is below 10 money units on amazon.

            1 Reply Last reply Reply Quote 0
            • Hergonowayundefined
              Hergonoway
              last edited by

              @DADIY:

              @Hergonoway:

              For my part I used these blowers fan 24v 404010mm : https://www.aliexpress.com/item/2PCS-Gdstime-40mm-40x10mm-4CM-DC-24V-0-1A-Mini-Turbo-Blower-Cooling-Cooler-Fan-For/32799434002.html

              10.25CFM, 24V works with PWM (without tuning M106, with default frequency F250)

              thanks for the link, I've just ordered a couple as for some reason the standard fan+shroud didn't fit my smart effector correctly. I just hope not to get burnt by Ali express again. The bed heater I ordered from there got lost in the post but they favoured the seller so I lost my money.

              Np, hope you like them. I'll share my fan mount for the smart effector once I finish my duet wifi box

              Delta goes BrrrRRRRrrrrrRRRRrrr

              1 Reply Last reply Reply Quote 0
              • Adrian52undefined
                Adrian52
                last edited by

                This is my smart effector with fan duct based on David's design (its on thingiverse 2521716).

                I have used my existing Traxxas rods with mounts that I put on thingiverse too (2492092). They seem to work very well - my best 8 parameter residual error is 0.005. As you can probably see, using Capricorn bowden tube, which seems excellent. Retraction of 2.4mm seems fine on the 60cm tube on my Kossel XL. Probe works wonderfully well. Not sure if my picture is going to appear though - haven't done this before.

                1 Reply Last reply Reply Quote 0
                • number40fanundefined
                  number40fan
                  last edited by

                  1 Reply Last reply Reply Quote 0
                  • Adrian52undefined
                    Adrian52
                    last edited by

                    Thank you (how did you do that?)

                    1 Reply Last reply Reply Quote 0
                    • Jareryundefined
                      Jarery
                      last edited by

                      Nice, what material did you use for the fan ducts ?

                      1 Reply Last reply Reply Quote 0
                      • number40fanundefined
                        number40fan
                        last edited by

                        I uploaded the picture to imgbb.com.

                        1 Reply Last reply Reply Quote 0
                        • Adrian52undefined
                          Adrian52
                          last edited by

                          I used e3d edge 'very black' PETG for the fan duct. I try not to leave it too long with the hot end hot and the print fan off - OK so far.

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Unless otherwise noted, all forum content is licensed under CC-BY-SA