Duet 2 Maestro Filament sensor Bed Temp
-
Hi everyone
Just realized my runout sensor stopped working after upgrade to 3.3M591 D0
Extruder 0 has no filament sensorthis is what I have in custom settings
; Custom settings
M591 D0 P2 C3 S1 ; Filament Run out sensorso I replaced that with M591 D0 P2 C"e0_stop" S1
M591 D0
Simple filament sensor on pin e0stop, enabled, output high when no filament, filament present: no
M591 D0
Simple filament sensor on pin e0stop, enabled, output high when no filament, filament present: yesit resolved - but temp shuts off when filament out
how do I tell it to keep bed temp on? -
-
Can you share your full config.g and the results of M122?
-
@fcwilt I dont have Filament-error file
I am assuming I need to create one. - how?I do have pause.g
pause.g
; called when a print from SD card is paused
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Nov 29 2021 17:18:27 GMT-0500 (Eastern Standard Time)
M83 ; relative extruder moves
G1 E-10 F3600 ; retract 10mm of filament
G91 ; relative positioning
G1 Z5 F360 ; lift Z by 5mm
G90 ; absolute positioning
G1 X0 Y0 F6000 ; go to X=0 Y=0M122
=== Diagnostics ===
RepRapFirmware for Duet 2 Maestro version 3.3 (2021-06-15 21:47:01) running on Duet Maestro 1.0
Board ID: 08DJM-956DU-LLMS4-7J1FG-3SN6Q-KAM6Q
Used output buffers: 1 of 24 (11 max)
=== RTOS ===
Static ram: 23556
Dynamic ram: 73216 of which 0 recycled
Never used RAM 18724, free system stack 220 words
Tasks: NETWORK(ready,23.4%,270) HEAT(delaying,0.1%,345) Move(notifyWait,0.1%,407) TMC(notifyWait,1.3%,117) MAIN(running,75.0%,481) IDLE(ready,0.2%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:43 ago, cause: power up
Last software reset at 2021-12-04 10:44, reason: User, GCodes spinning, available RAM 18724, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 938
MCU temperature: min 31.0, current 32.9, max 33.4
Supply voltage: min 24.1, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
Driver 1: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
Driver 2: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
Driver 3: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
Driver 4: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
Driver 5: position 0, assumed not present
Driver 6: position 0, assumed not present
Date/time: 2021-12-04 12:54:14
Slowest loop: 3.50ms; fastest: 0.16ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 15.0MBytes/sec
SD card longest read time 3.3ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 114.07ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps half duplexfull config
; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Nov 29 2021 17:18:26 GMT-0500 (Eastern Standard Time); General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"E5Maestro" ; set printer name; Network
M552 P192.168.2.212 S1 ; enable network and set IP address
M553 P255.255.255.0 ; set netmask
M554 P192.168.1.1 ; set gateway
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z1600.00 E936.675 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z300.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E900 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X325 Y320 Z400 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z; Z-Probe
M950 S0 C"zprobe.mod";M950 S0 C"exp.heater7" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H2.5 F180 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X44 Y2 Z2 ; set Z probe trigger value, offset and trigger height
M557 X0:310 Y0:285 S50 ;M557 X10:320 Y10:320 S50 ;M557 X0:305 Y0:315 S50 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C; Fans
;M950 F0 C"!fan1" Q500 ; create fan 0 on pin !fan1 and set its frequency
;M106 P0 S1 H-1
M950 F0 C"fan1" Q500 ; create fan 0 on pin fan1 and set its frequency
M106 P0 S1 H-1
;M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
;M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings
M591 D0 P2 C"e0_stop" S1 ;M591 D0 P2 C3 S1 ; Filament Run out sensor
G29 S1 ; Load mesh bed
M564 H0 ; Process config overrides
M918 P1 E-4 ; Activate LCD12864; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss -
filament-error is optional. Pause.g would be run if it's not present.
