Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • Documentation
    • Order
    1. Home
    2. ap742
    • Profile
    • Following 1
    • Followers 0
    • Topics 9
    • Posts 36
    • Best 2
    • Controversial 0
    • Groups 0

    ap742

    @ap742

    2
    Reputation
    1
    Profile views
    36
    Posts
    0
    Followers
    1
    Following
    Joined Last Online

    ap742 Unfollow Follow

    Best posts made by ap742

    • RE: Duet 2 wifi 3.2.2 runout sensor

      @phaedrux Figured it out . it was wiring . originally I had it plugged in backwords into duet and instead of getting all the way in there and flipping I flipped them at the switch and signal pin was bad so I just re terminated all 3 and did the M591D with switch in and out and get Filament yes and now .. woooohooooo

      Thank You good Sir

      posted in Filament Monitor
      ap742
      ap742
    • RE: Ender 3 Pro driving past end stops after stopping

      I think I found my mistake .

      M574 X2 S1 P"xstop"
      M574 Y2 S1 P"ystop"

      had X&Y set to 1
      changed it to 2 helped

      posted in Duet Hardware and wiring
      ap742
      ap742

    Latest posts made by ap742

    • RE: height map off set to negative ?

      @Adamfilip
      what do you mean make that area 0? how?

      did you just edit heghtmap.csv and correct the numbers?

      posted in Tuning and tweaking
      ap742
      ap742
    • RE: height map off set to negative ?

      @Phaedrux

      Z is typical ender 5 plus config nothing really changed there.
      its 2mm pitch 4mm lead
      10mm linear rods all lubed with synthetic lube
      z is pretty smooth

      driven by two steppers 0.8A 1.8 degree

      d0235c0f-7363-4c99-a95b-77f7c83f06a3-image.png

      here's my bed config

      ; bed.g
      ; called to perform automatic bed compensation via G32
      ;
      ; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Apr 16 2021 19:18:05 GMT-0400 (Eastern Daylight Time)
      M561 ; clear any bed transform
      G29 ; probe the bed and enable compensation

      so the way do it is

      home all use 0.1 mm spacer to to get nozzle down to bed.
      and repeat all this few times around all corners and center

      than I run G31 S-1 few times to get average number for G31

      after that I run G29

      posted in Tuning and tweaking
      ap742
      ap742
    • RE: height map off set to negative ?

      @Phaedrux

      so before I tear down and re check all the bearings and stuff " all new but we all know there's always chance "

      here's what map looks like not perfect but.....
      a658913f-b4a7-4e80-9100-523c6c1466e5-image.png

      this is the front of the bed between 275 & 300

      bd3ba0a9-0da8-48ad-bc7b-faa60c264a59-image.png

      this one is the back between 50 and 75

      5ccbcd4c-3c8c-4d40-b640-1fda3feaded3-image.png

      Thank You

      posted in Tuning and tweaking
      ap742
      ap742
    • RE: height map off set to negative ?

      @Phaedrux
      Thank you 🙂
      so I'm going to lean towards mechanical stuff . because its doing exactly the same thing as it did before

      my starting gcode loads G29 S1 - assuming it should compensate

      M106 S0 ; turn off cooling fan
      G28
      G29 S1
      G92 E0 ; Reset Extruder
      G1 Z10.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
      G1 X344.5 Y300 Z0.28 F5000.0 ;Move to start position
      G1 X344.5 Y90.0 Z0.28 F1500.0 E15 ;Draw the first line
      G1 X344.7 Y90.0 Z0.28 F5000.0 ;Move to side a little
      G1 X344.7 Y300 Z0.28 F1500.0 E30 ;Draw the second line

      G92 E0 ; reset extrusion distance
      G1 Z15.0 F6000 ;Move the nozzle up 15mm
      G92 E0 ; Reset the extruder's origin

      posted in Tuning and tweaking
      ap742
      ap742
    • RE: height map off set to negative ?

      @Phaedrux

      Thank You for that

      so I got that changed

      G31 P25 X41 Y-9.44 Z2.121

      how about define the mesh

      M557 X41:280 Y20:340 S38 if I do this it doesn't probe high end all the way

      0f8cd797-0b46-48ea-9877-2fc8ff585865-image.png

      posted in Tuning and tweaking
      ap742
      ap742
    • RE: height map off set to negative ?

      @Phaedrux

      +x moves to the left from the end stop which is 0
      +y moves to the front from the end stop which is 0

      e7fb9a3b-4df9-4cb4-abef-f319f50b5f23-image.png

      here's my config

      ; Configuration file for Duet WiFi (firmware version 3)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Apr 16 2021 19:18:05 GMT-0400 (Eastern Daylight Time)

      ; General preferences
      G90 ; send absolute coordinates...
      M83 ; ...but relative extruder moves
      M550 P"E5" ; set printer name

      ;MCU temp
      M912 P0 S21 - 26

      ; Network
      M552 S1 ; enable network
      M586 P0 S1 ; enable HTTP
      M586 P1 S0 ; disable FTP
      M586 P2 S0 ; disable Telnet

      ; Drives
      M569 P0 S1 ; physical drive 0 goes forwards
      M569 P1 S1 ; physical drive 1 goes forwards
      M569 P2 S0 ; physical drive 2 goes backwards
      M569 P3 S0 ; physical drive 3 goes backwards
      M584 X0 Y1 Z2 E3 ; set drive mapping
      M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
      M92 X80.00 Y80.00 Z800.00 E486.584 ; set steps per mm
      M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
      M203 X6000.00 Y6000.00 Z300.00 E1200.00 ; set maximum speeds (mm/min)
      M201 X500.00 Y500.00 Z20.00 E500.00 ; set accelerations (mm/s^2)
      M906 X800 Y800 Z800 E1000 I30 ;Y800 Z800 E900 I30 ; set motor currents (mA) and motor idle factor in per cent
      M84 S30 ; Set idle timeout

      ; Axis Limits
      M208 X0 Y0 Z0 S1 ; set axis minima
      M208 X355 Y343 Z400 S0 ; set axis maxima x350 M208 X350 Y350 Z400 S0 <- hemera

      ; Endstops
      M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
      M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
      M574 Z0 ; configure Z-probe endstop on Z
      M591 P1 C"e0stop" S1 D0

      ; Z-Probe
      M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
      M558 P9 C"^zprobe.in" H2.5 F180 T6000 ; set Z probe type to bltouch and the dive height + speeds H2.5
      G31 P25 X-41 Y9.44 Z2.121 ; set Z probe trigger value, offset and trigger height
      M557 X-41:280 Y20:340 S38 ; define mesh grid

      ; Heaters
      ;M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
      ;M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      ;M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
      ;M140 H0 ; map heated bed to heater 0
      ;M143 H0 S120 ; set temperature limit for heater 0 to 120C
      ;M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
      ;M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      ;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
      ;M143 H1 S280 ; set temperature limit for heater 1 to 280C

      ; Heaters
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      ;M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
      M140 H0 ; map heated bed to heater 0
      M143 H0 S120 ; set temperature limit for heater 0 to 120C
      M308 S1 P"e0temp" Y"thermistor" A"Hotend" T100000 B4725 C7.06e-8 ;M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      ;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
      M143 H1 S300 ; set temperature limit for heater 1 to 300C

      ; Fans
      M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
      M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
      M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
      M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

      ; Tools
      M563 P0 D0 H1 F0 ; define tool 0
      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

      ; Custom settings
      ;591 D0 P2 C3 S1 ; Filament Run out sensor

      ; Miscellaneous
      M575 P1 S1 B57600 ; enable support for PanelDue
      M501 ; load saved parameters from non-volatile memory
      M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
      M307 H1 R2.896 C205.2:122.7 D7.66 S1.00 V24.2

      here's my homeall

      ; homeall.g
      ; called to home all axes
      ;
      ; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Apr 16 2021 19:18:06 GMT-0400 (Eastern Daylight Time)
      G91 ; relative positioning
      G1 H2 Z2.5 F6000 ; lift Z relative to current position
      G1 H1 X-360.5 Y-355 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
      G1 H2 X5 Y5 F6000 ; go back a few mm
      G1 H1 X-360.5 Y-355 F360 ; move slowly to X and Y axis endstops once more (second pass)
      ;G1 H1 Z-405 F360 ; move Z down stopping at the endstop
      ;G90 ; absolute positioning
      ;G92 Z0 ; set Z position to axis minimum (you may want to adjust this)
      ;G1 X220 Y175 F4000 ; Move probe to middle of bed
      G1 X140 Y160 F6000 ; go to first probe point
      M558 F500 A1 ; probe once quickly
      G30
      M558 F120 A10 ; detailed probe
      G30

      Thank You

      posted in Tuning and tweaking
      ap742
      ap742
    • height map off set to negative ?

      hi guys I'm stuck. - running 3.4.4 duet 2 wifi - " printer Ender 5 plus "

      was fine till I did exoslide upgrade and exoslide hotend.

      pretty much moved my bltouch offset and stuff .

      so I started from scratch
      G31 P25 X-41 Y9.44 Z2.121
      M557 X-41:280 Y20:340 S38

      also added homeall because it wasn't compensating
      M558 F500 A1 ; probe once quickly
      G30
      M558 F120 A10 ; detailed probe
      G30

      031f07b0-1596-4230-890f-84278127c4f5-image.png

      so this is latest G29

      anyway no matter what the height map looks like - it'll print way to close to bed at the front of the bed

      if I understand correct compensation happens when numbers bit negative ? if so how do I adjust for the map to be bit below the grid ?
      😞

      posted in Tuning and tweaking
      ap742
      ap742
    • RE: Duet 2 Maestro Filament sensor Bed Temp

      @fcwilt I dont have Filament-error file
      I am assuming I need to create one. - how?

      I do have pause.g

      pause.g
      ; called when a print from SD card is paused
      ;
      ; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Nov 29 2021 17:18:27 GMT-0500 (Eastern Standard Time)
      M83 ; relative extruder moves
      G1 E-10 F3600 ; retract 10mm of filament
      G91 ; relative positioning
      G1 Z5 F360 ; lift Z by 5mm
      G90 ; absolute positioning
      G1 X0 Y0 F6000 ; go to X=0 Y=0

      @phaedrux

      M122
      === Diagnostics ===
      RepRapFirmware for Duet 2 Maestro version 3.3 (2021-06-15 21:47:01) running on Duet Maestro 1.0
      Board ID: 08DJM-956DU-LLMS4-7J1FG-3SN6Q-KAM6Q
      Used output buffers: 1 of 24 (11 max)
      === RTOS ===
      Static ram: 23556
      Dynamic ram: 73216 of which 0 recycled
      Never used RAM 18724, free system stack 220 words
      Tasks: NETWORK(ready,23.4%,270) HEAT(delaying,0.1%,345) Move(notifyWait,0.1%,407) TMC(notifyWait,1.3%,117) MAIN(running,75.0%,481) IDLE(ready,0.2%,30), total 100.0%
      Owned mutexes:
      === Platform ===
      Last reset 00:01:43 ago, cause: power up
      Last software reset at 2021-12-04 10:44, reason: User, GCodes spinning, available RAM 18724, slot 0
      Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
      Error status: 0x00
      Aux0 errors 0,0,0
      Step timer max interval 938
      MCU temperature: min 31.0, current 32.9, max 33.4
      Supply voltage: min 24.1, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
      Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
      Driver 0: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
      Driver 1: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
      Driver 2: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
      Driver 3: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
      Driver 4: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
      Driver 5: position 0, assumed not present
      Driver 6: position 0, assumed not present
      Date/time: 2021-12-04 12:54:14
      Slowest loop: 3.50ms; fastest: 0.16ms
      I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
      === Storage ===
      Free file entries: 10
      SD card 0 detected, interface speed: 15.0MBytes/sec
      SD card longest read time 3.3ms, write time 0.0ms, max retries 0
      === Move ===
      DMs created 83, maxWait 0ms, bed compensation in use: mesh, comp offset 0.000
      === MainDDARing ===
      Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
      === AuxDDARing ===
      Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
      === Heat ===
      Bed heaters = 0 -1, chamberHeaters = -1 -1
      === GCodes ===
      Segments left: 0
      Movement lock held by null
      HTTP is idle in state(s) 0
      Telnet is idle in state(s) 0
      File is idle in state(s) 0
      USB is idle in state(s) 0
      Aux is idle in state(s) 0
      Trigger is idle in state(s) 0
      Queue is idle in state(s) 0
      LCD is idle in state(s) 0
      Daemon is idle in state(s) 0
      Autopause is idle in state(s) 0
      Code queue is empty.
      === Filament sensors ===
      Extruder 0 sensor: ok
      === Network ===
      Slowest loop: 114.07ms; fastest: 0.02ms
      Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
      HTTP sessions: 1 of 8
      Interface state active, link 100Mbps half duplex

      full config

      ; Configuration file for Duet WiFi (firmware version 3.3)
      ; executed by the firmware on start-up
      ;
      ; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Nov 29 2021 17:18:26 GMT-0500 (Eastern Standard Time)

      ; General preferences
      M575 P1 S1 B57600 ; enable support for PanelDue
      G90 ; send absolute coordinates...
      M83 ; ...but relative extruder moves
      M550 P"E5Maestro" ; set printer name

      ; Network
      M552 P192.168.2.212 S1 ; enable network and set IP address
      M553 P255.255.255.0 ; set netmask
      M554 P192.168.1.1 ; set gateway
      M586 P0 S1 ; enable HTTP
      M586 P1 S0 ; disable FTP
      M586 P2 S0 ; disable Telnet

      ; Drives
      M569 P0 S1 ; physical drive 0 goes forwards
      M569 P1 S1 ; physical drive 1 goes forwards
      M569 P2 S0 ; physical drive 2 goes backwards
      M569 P3 S0 ; physical drive 3 goes backwards
      M584 X0 Y1 Z2 E3 ; set drive mapping
      M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
      M92 X80.00 Y80.00 Z1600.00 E936.675 ; set steps per mm
      M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
      M203 X6000.00 Y6000.00 Z300.00 E1200.00 ; set maximum speeds (mm/min)
      M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
      M906 X800 Y800 Z800 E900 I30 ; set motor currents (mA) and motor idle factor in per cent
      M84 S30 ; Set idle timeout

      ; Axis Limits
      M208 X0 Y0 Z0 S1 ; set axis minima
      M208 X325 Y320 Z400 S0 ; set axis maxima

      ; Endstops
      M574 X1 S1 P"xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
      M574 Y1 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
      M574 Z1 S2 ; configure Z-probe endstop for low end on Z

      ; Z-Probe
      M950 S0 C"zprobe.mod";M950 S0 C"exp.heater7" ; create servo pin 0 for BLTouch
      M558 P9 C"^zprobe.in" H2.5 F180 T6000 ; set Z probe type to bltouch and the dive height + speeds
      G31 P500 X44 Y2 Z2 ; set Z probe trigger value, offset and trigger height
      M557 X0:310 Y0:285 S50 ;M557 X10:320 Y10:320 S50 ;M557 X0:305 Y0:315 S50 ; define mesh grid

      ; Heaters
      M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
      M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
      M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
      M140 H0 ; map heated bed to heater 0
      M143 H0 S120 ; set temperature limit for heater 0 to 120C
      M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
      M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
      M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
      M143 H1 S280 ; set temperature limit for heater 1 to 280C

      ; Fans
      ;M950 F0 C"!fan1" Q500 ; create fan 0 on pin !fan1 and set its frequency
      ;M106 P0 S1 H-1
      M950 F0 C"fan1" Q500 ; create fan 0 on pin fan1 and set its frequency
      M106 P0 S1 H-1
      ;M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
      ;M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
      ; Tools
      M563 P0 D0 H1 F0 ; define tool 0
      G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
      G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

      ; Custom settings
      M591 D0 P2 C"e0_stop" S1 ;M591 D0 P2 C3 S1 ; Filament Run out sensor
      G29 S1 ; Load mesh bed
      M564 H0 ; Process config overrides
      M918 P1 E-4 ; Activate LCD12864

      ; Miscellaneous
      M501 ; load saved parameters from non-volatile memory
      M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

      posted in Firmware installation
      ap742
      ap742
    • Duet 2 Maestro Filament sensor Bed Temp

      Hi everyone
      Just realized my runout sensor stopped working after upgrade to 3.3

      M591 D0
      Extruder 0 has no filament sensor

      this is what I have in custom settings

      ; Custom settings
      M591 D0 P2 C3 S1 ; Filament Run out sensor

      so I replaced that with M591 D0 P2 C"e0_stop" S1
      M591 D0
      Simple filament sensor on pin e0stop, enabled, output high when no filament, filament present: no
      M591 D0
      Simple filament sensor on pin e0stop, enabled, output high when no filament, filament present: yes

      it resolved - but temp shuts off when filament out
      how do I tell it to keep bed temp on?

      posted in Firmware installation
      ap742
      ap742
    • RE: Duet 2 maestro Upgrade Heightmap issues

      @dc42 after I asked the question I went to ready more and yah 😞 one day I learn how to read .. lol
      I missed Upgrading ANY Duet 2 from 2.x to 3.0 or later requires installing 3.0 first.
      anyway that did it . thank you for replying 🙂
      I'm going to re do cable management-(have feeling it might have enough tension to do weird stuff and carriage and check bearings on my exoslids

      posted in Firmware installation
      ap742
      ap742