BLTouch w/ DUet 3 mini 5+ Wifi (Ender 3 Pro)

Gixxerfast

Yes for now anyway, You could move the M950 down to the Z-probe section as it's where it belongs right now. But that's only a detail.

At a glance your homing scripts looks alright.

You might want to set the x and y offset of the probe in the G31 (in z-probe section in config.g) since I assume that you don't have your probe at the same position as the nozzle

But, you could start with that and see what happens. Only make sure that you have enough Z to start with so that the probe pin can deploy without touching the bed.

Edit: As a note, you might want to in homeall.g and homez.g move to th emiddle of the bed (adjusted with the probe offset) before go probe (G30)

Edit2: A stock position for BLTouch x and y a ENder3 is usually here:

G31 P500 X-40 Y-12 Z2.5

Edit3: Here
s a cool thing I found from Team Gloomy's config example. In your homez.g and homeall.g when you move to probe (G30) and you want to do it in th emiddle of the bed this is really cool (Note, it's all one line)

G1 X{(move.axes[0].max/2)+abs(sensors.probes[0].offsets[0])} Y{(move.axes[1].max/2)+abs(sensors.probes[0].offsets[1])} F10000

Here's the rest of the config example: https://github.com/TeamGloomy/ender-3-fly-E3/tree/bltouch

teachmedavis747

@gixxerfast

Very interesting. I copied their homeall.g and homez.g

I tried the g30 command but the BLTouch did not deploy. i stopped it before it crashed into the bed. I also tried to home XY but for some reason the pins are not being read. Any ideas on these issues?

Gixxerfast

@teachmedavis747 OK, so:

EDIT: Forgot: Do you have the deployprobe.g and the retractprobe.g in your /sys directory? How do they look ?

EDIT2: Your endstop config is correct. But how have you connected them. It should be ground and in-pin? Move the bed to the endstop and the x-carriage also to the endstop and check status with M119

Does the BLTouch glow red when the printer is on?
WHen you start the printer does it deploy and stove the pin twice as a startup routine?

Can you show how you have connected the probe wires ? Picture ?

There are so many different colour variations of the wiring so do you remember how you had it connected with Marlin?

teachmedavis747

@gixxerfast

Yes, It glows red and deploys twice once powered on.

Here is a picture of the wiring:
2022-01-02 15.40.jpg

Edit:

Here is deployprobe.g

M280 P0 S10

and retractprobe.g

M280 P0 S90

Edit 2: Here is the M119 with both x and y at the endstops:

Printer is now online.
>>> m119
SENDING:M119
Endstops - X: at min stop, Y: at min stop, Z: no endstop, Z probe: not stopped

Gixxerfast

@teachmedavis747 Run:

 M280 P0 S10

and see what happens. Then try

 M280 P0 S90

teachmedavis747

@gixxerfast

Nothing happens when I send either deploy or retract

Gixxerfast

@teachmedavis747 said in BLTouch w/ DUet 3 mini 5+ Wifi (Ender 3 Pro):

Edit 2: Here is the M119 with both x and y at the endstops:
Printer is now online. >>> m119 SENDING:M119 Endstops - X: at min stop, Y: at min stop, Z: no endstop, Z probe: not stopped

Yes, but that seems to work just fine

Gixxerfast

@teachmedavis747 said in BLTouch w/ DUet 3 mini 5+ Wifi (Ender 3 Pro):

Nothing happens when I send either deploy or retract

OK, this should work, Can you send a picture of the BLTouch where you can see the wires as they go into the probe just to make sure that the right wires goes to the correvt places. We know that 5v and ground is correct. But we should be able to deploy with the config that your have.

You have saved and restarted after the changes right?

Gixxerfast

@teachmedavis747 Also, please post your complete config.g again.
Just to make sure ...

teachmedavis747

@gixxerfast

Hi. I apologize for the delay. I was under the weather a few days. While I was down I ordered some new wires for the BLTouch. I installed them today and figured out that was my issue as far as deploying the probe. Fixed.

Question for you. When I hit "Home X"and "home y"... should the bed and X axis move towards the end stop pin? They do not make that move.

Gixxerfast

@teachmedavis747 That's great.

Yes, as long as you have a homex.g and a homey.g containing homing instruction in your /sys directory

teachmedavis747

@gixxerfast

Okay. I was able to get it to run G28. However, another issue. Maybe you can help me with this as well. I had to switch the direction of the x and y axis motors in config.g. (I replaced the x axis motor with a high torque motor from e3d).

When I enter G28 the extruder travels in the wrong direction. Instead of going towards the pin, it travels the opposite direction. How can I fix the homing files to compensate for this change? I will attach my config.g and homeall

Homeall

; homeall.g
; called to home all axes
;
;
; generated by RepRapFirmware Configuration Tool v3.1.10+4-LPC on Wed Jan 06 2021 14:08:16 GMT+0000 (Greenwich Mean Time)
G91                     ; relative positioning
G1 H2 Z5 F6000          ; lift Z relative to current position
G1 H1 X-240 Y240 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000       ; go back a few mm
G1 H1 X-240 Y240 F360  ; move slowly to X and Y axis endstops once more (second pass)
G90
G1 X{(move.axes[0].max/2)+abs(sensors.probes[0].offsets[0])} Y{(move.axes[1].max/2)+abs(sensors.probes[0].offsets[1])} F10000

; ################# Home Z Preparation ################

M558 F250 				 										; Set the probing speed
G30

config.g

; Configuration file for Duet 3 Mini 5+ (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Sun Jan 02 2022 00:25:05 GMT-0700 (Mountain Standard Time)

; General preferences
M575 P1 S1 B57600                                  ; enable support for PanelDue
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"Prender"                                    ; set printer name
M918 P1 E4 F2000000                                ; configure direct-connect display

; Network
M552 S1                                            ; enable network
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0.0 S0                                       ; physical drive 0.0 goes backwards
M569 P0.1 S0                                       ; physical drive 0.1 goes backwards
M569 P0.2 S1                                       ; physical drive 0.2 goes forwards
M569 P0.3 S0                                       ; physical drive 0.3 goes backwards
M584 X0.0 Y0.1 Z0.2 E0.3                           ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E93.00                   ; set steps per mm
M566 X1200.00 Y1200.00 Z24.00 E300.00              ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E6000.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00              ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E1000 I50                      ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X235 Y235 Z235 S0                             ; set axis maxima

; Endstops
M574 X1 S1 P"io5.in"                               ; configure switch-type (e.g. microswitch) endstop for low end on X via pin io5.in
M574 Y1 S1 P"io6.in"                               ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin io6.in


; Z-Probe
M950 S0 C"io3.out"                                 ; Duet 3 Mini 5+
M558 P9 C"io3.in" H5 F120 T6000                    ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X-19 Y-28 Z2.5                                ; set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20                           ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4092       ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00                                   ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                            ; map heated bed to heater 0
M143 H0 S150                                       ; set temperature limit for heater 0 to 150C
M308 S1 P"temp1" Y"thermistor" T100000 B4092       ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1                                 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S275                                       ; set temperature limit for heater 1 to 275C

; Fans
M950 F0 C"out5" Q500                               ; create fan 0 on pin out5 and set its frequency
M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"out6" Q500                               ; create fan 1 on pin out6 and set its frequency
M106 P1 S1 H1 T45                                  ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                   ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

homex

; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Sun Jan 02 2022 00:25:05 GMT-0700 (Mountain Standard Time)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 X-240 F3000 ; move quickly to X axis endstop and stop there (first pass)
G1 H2 X5 F6000    ; go back a few mm
G1 H1 X-240 F240  ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90               ; absolute positioning

homey

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Sun Jan 02 2022 00:25:05 GMT-0700 (Mountain Standard Time)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 Y240 F3000 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 F6000    ; go back a few mm
G1 H1 Y240 F240  ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90               ; absolute positioning

Phaedrux

@teachmedavis747 said in BLTouch w/ DUet 3 mini 5+ Wifi (Ender 3 Pro):

How can I fix the homing files to compensate for this change?

There are 3 parts to this. The direction of motor rotation, the endstop position definition, and the movement direction in the homing macros.

-x should move left, +x should move right
-y should move to the front, +y should move to the back

M569 is where the rotation direction is set

M574 defines where the endstops are located. high end of travel (positive move to reach) or low end of travel (negative move to reach)

The G1 H moves in the homing macros should move towards the endstop either positive or negative.

If you require more guidance we'd need to at least know where your endstops are physically located to know if your config is correct.

Gixxerfast

@teachmedavis747 Hmm, from the top of my head I know of no special homing or probe related changes needed to fix that. Are you sure your Z-motor doesn't need reversing as well?

When you home x and y does z move in the right direction. Up and then down again?

teachmedavis747

@gixxerfast Yes. Z-axis moves well.

teachmedavis747

@phaedrux Sure.

On the ender 3 the x-axis endstop pin is located on the far left of the x-axis. The y-axis is located at the back of the printer next to the y-axis stepper motor. I believe I have it set at low end for both when I configured the file using the RepRap tool.

So if I changed the direction in 569 for both the x and y-axis motors... what others changes would be needed to get it to g28 in the right direction?

y endstop.jpg x endstop.jpg

Gixxerfast

@teachmedavis747 said in BLTouch w/ DUet 3 mini 5+ Wifi (Ender 3 Pro):

When I enter G28 the extruder travels in the wrong direction. Instead of going towards the pin, it travels the opposite direction.

Just do be clear can you explain what you mean here exactly?

Your homeall.g is not correct as it moves the y in the wrong direction. You should try to go to relative -(max bed size x + some more) and -(max bed size y + some more)

Also, I would split that so I first home x, then y and lastly z.

In my homeall.g I just call homex.g, homey.g and homez.g instead of repeating the commands again.

Phaedrux

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Sun Jan 02 2022 00:25:05 GMT-0700 (Mountain Standard Time)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 Y240 F3000 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 F6000    ; go back a few mm
G1 H1 Y240 F240  ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90               ; absolute positioning

The Y endstop is at the min, so all the Y homing moves in here should be negative, but all your moves are positive, so that needs to be fixed.

@phaedrux said in BLTouch w/ DUet 3 mini 5+ Wifi (Ender 3 Pro):

-x should move left, +x should move right
-y should move to the front, +y should move to the back

Can you confirm this is the case? Note that for Y, movement of the bed is relative to the print head. So even though the bed moves forward, the print head is now at the rear of the bed, and vice versa.

teachmedavis747

@phaedrux

confirmed. When i go to MOVE on my display if I hit +1 the x axis moves rights. However, you were correct. The y-axis was moving the wrong direction. Here's the format I think you were referencing.

So I changed the config.g 569 to match this and now all is moving in the correct direction.

M569 P0.0 S0                                       ; physical drive 0.0 goes backwards
*M569 P0.1 S1                                       ; physical drive 0.1 goes forwards*
M569 P0.2 S1                                       ; physical drive 0.2 goes forwards
M569 P0.3 S0                                       ; physical drive 0.3 goes backwards

Edit: I also changed the homey. Is this correct?

G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 Y-240 F3000 ; move quickly to Y axis endstop and stop there (first pass)
G1 H2 Y5 F6000    ; go back a few mm
G1 H1 Y-240 F240  ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90               ; absolute positioning

teachmedavis747

@gixxerfast

Instead of the print head moving toward the endstop pin... it travels to the right.. away from the pin.

Edit:

Can you send me an example of what that would look like... as far as separating the x and y and z?