Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    No function after update

    Scheduled Pinned Locked Moved Unsolved
    Firmware installation
    5
    19
    729
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • chrishammundefined
      chrishamm administrators @Wladekcz
      last edited by

      @wladekcz You should not use Google Translate to translate DWC, it's better to go to Settings -> General and to select Polish there - else the web interface appears to freeze as you could observe.

      Can you confirm that you have DWC 3.4.0 installed as well (check on Settings -> General)? It's hard to tell if the malfunction is caused by the external translation service but if it perists after a fresh reload (without Google Translate), please press F12, go to the JS console, and post the log here. Perhaps DWC fails to parse something from the object model.

      Duet software engineer

      1 Reply Last reply Reply Quote 0
      • Wladekczundefined
        Wladekcz
        last edited by

        Was that what it was about?

        chrome-extension://ihcjicgdanjaechkgeegckofjjedodee/content-scripts.js

        Władekcz

        chrishammundefined 1 Reply Last reply Reply Quote 0
        • Wladekczundefined
          Wladekcz
          last edited by

          After selecting the Polish language in the settings, you can see the temperature. There is no change under the tools with the heater on and off. The inscription in English OFF regardless of its condition.

          Władekcz

          1 Reply Last reply Reply Quote 0
          • Wladekczundefined
            Wladekcz
            last edited by

            WDC 3,4,0

            Władekcz

            1 Reply Last reply Reply Quote 0
            • Wladekczundefined
              Wladekcz
              last edited by

              content-scripts.txt

              Władekcz

              1 Reply Last reply Reply Quote 0
              • chrishammundefined
                chrishamm administrators @Wladekcz
                last edited by

                @wladekcz Looks like a Chrome extension so nothing caused by DWC. Please try another browser and check if the problem persists. If it does, please share your homeall.g as well.

                Duet software engineer

                1 Reply Last reply Reply Quote 0
                • Phaedruxundefined
                  Phaedrux Moderator
                  last edited by

                  ; Configuration file for Duet 3 (firmware version 3.3)
                  ; executed by the firmware on start-up
                  ;
                  ; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Apr 21 2022 10:03:29 GMT+0200 (czas środkowoeuropejski letni)
                  
                  ; General preferences
                  M575 P1 S1 B57600                                         ; enable support for PanelDue
                  G90                                                       ; send absolute coordinates...
                  M83                                                       ; ...but relative extruder moves
                  M550 P"My Duet3"                                          ; set printer name
                  M669 K1                                                   ; select CoreXY mode
                  
                  ; Wait a moment for the CAN expansion boards to start
                  G4 S2
                  
                  ; Network
                  M552 P0.0.0.0 S1                                          ; enable network and acquire dynamic address via DHCP
                  M586 P0 S1                                                ; enable HTTP
                  M586 P1 S0                                                ; disable FTP
                  M586 P2 S0                                                ; disable Telnet
                  
                  ; Drives
                  M569 P0.0 S0                                              ; physical drive 0.0 goes backwards
                  M569 P0.2 S0                                              ; physical drive 0.2 goes backwards
                  M569 P0.3 S1                                              ; physical drive 0.3 goes forwards
                  M569 P0.4 S1                                              ; physical drive 0.4 goes forwards
                  M584 X0.0 Y0.2 Z0.3 E0.4                                  ; set drive mapping
                  M350 X16 Y16 Z16 E16 I1                                   ; configure microstepping with interpolation
                  M92 X80.00 Y80.00 Z407.00 E1168.00                        ; set steps per mm
                  M566 X900.00 Y900.00 Z60.00 E120.00                       ; set maximum instantaneous speed changes (mm/min)
                  M203 X6000.00 Y6000.00 Z180.00 E1200.00                   ; set maximum speeds (mm/min)
                  M201 X500.00 Y500.00 Z20.00 E250.00                       ; set accelerations (mm/s^2)
                  M906 X800 Y800 Z800 E800 I30                              ; set motor currents (mA) and motor idle factor in per cent
                  M84 S30                                                   ; Set idle timeout
                  
                  ; Axis Limits
                  M208 X0 Y0 Z0 S1                                          ; set axis minima
                  M208 X330 Y330 Z370 S0                                    ; set axis maxima
                  
                  ; Endstops
                  M574 X1 S1 P"io2.in"                                      ; configure switch-type (e.g. microswitch) endstop for low end on X via pin io2.in
                  M574 Y1 S1 P"io1.in"                                      ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin io1.in
                  M574 Z1 S2                                                ; configure Z-probe endstop for low end on Z
                  
                  ; Z-Probe
                  M558 P1 C"!io7.in" H5 F120 T6000                          ; set Z probe type to unmodulated and the dive height + speeds
                  G31 P500 X19 Y5 Z2.26                                    ; set Z probe trigger value, offset and trigger height
                  M557 X30:280 Y30:280 S30                                  ; define mesh grid
                  
                  ; Heaters
                  M308 S0 P"temp0" Y"thermistor" T100000 B5438 C1.335272e-7 ; configure sensor 0 as thermistor on pin temp0
                  M950 H0 C"out0" T0                                        ; create bed heater output on out0 and map it to sensor 0
                  M307 H0 B1 S1.00                                          ; enable bang-bang mode for the bed heater and set PWM limit
                  M140 H0                                                   ; map heated bed to heater 0
                  M143 H0 S120                                              ; set temperature limit for heater 0 to 120C
                  M308 S1 P"temp3" Y"thermistor" T100000 B5438 C1.335272e-7 ; configure sensor 1 as thermistor on pin temp3
                  M950 H1 C"out1" T1                                        ; create nozzle heater output on out1 and map it to sensor 1
                  M307 H1 B0 S1.00                                          ; disable bang-bang mode for heater  and set PWM limit
                  M143 H1 S280                                              ; set temperature limit for heater 1 to 280C
                  M308 S2 P"1.temp1" Y"thermistor" T9400 B5438 C1.335272e-7 ; configure sensor 2 as thermistor on pin 1.temp1
                  M950 H2 C"out2" T2                                        ; create chamber heater output on out2 and map it to sensor 2
                  M307 H2 B1 S1.00                                          ; enable bang-bang mode for the chamber heater and set PWM limit
                  M141 H2                                                   ; map chamber to heater 2
                  M143 H2 S60                                               ; set temperature limit for heater 2 to 60C
                  
                  ; Fans
                  M950 F0 C"out9" Q500                                      ; create fan 0 on pin out9 and set its frequency
                  M106 P0 S0 H T45                                          ; set fan 0 value. Thermostatic control is turned on
                  M950 F1 C"out4" Q500                                      ; create fan 1 on pin out4 and set its frequency
                  M106 P1 S1 H1 T45                                         ; set fan 1 value. Thermostatic control is turned on
                  M950 F2 C"out5" Q500                                      ; create fan 2 on pin out5 and set its frequency
                  M106 P2 S1 H2:1 T45                                       ; set fan 2 value. Thermostatic control is turned on
                  M950 F3 C"out7" Q500                                      ; create fan 3 on pin out7 and set its frequency
                  M106 P3 S1 H1 T40                                         ; set fan 3 value. Thermostatic control is turned on
                  
                  ; Tools
                  M563 P0 D0 H1 F0                                          ; define tool 0
                  G10 P0 X0 Y0 Z0                                           ; set tool 0 axis offsets
                  G10 P0 R0 S0                                              ; set initial tool 0 active and standby temperatures to 0C
                  
                  
                  M912 P0 S-17											  ;Kalibracja temperatury MCU
                  
                  ; Custom settings are not defined
                  
                  ; Miscellaneous
                  M501                                                      ; load saved parameters from non-volatile memory
                  M911 S20 R21 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"        ; set voltage thresholds and actions to run on power loss
                  

                  Can you please try adding T0 to the end of your config.g to see if it will allow you to extrude when the hotend is at temp.

                  ; bed.g
                  ; called to perform automatic bed compensation via G32
                  ;
                  ; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Apr 21 2022 10:03:29 GMT+0200 (czas środkowoeuropejski letni)
                  M561 ; clear any bed transform
                  G29  ; probe the bed and enable compensation
                  

                  Do you have a mesh.g file in your system folder?

                  When you choose "True Bed Leveling (G32)" from the drop down, what are you expecting to happen?

                  Selecting that drop down item will call bed.g, which in your case, only contains a call for G29 which itself just runs mesh.g.

                  What do you want it to do?

                  Z-Bot CoreXY Build | Thingiverse Profile

                  Phaedruxundefined 1 Reply Last reply Reply Quote 0
                  • Phaedruxundefined
                    Phaedrux Moderator @Phaedrux
                    last edited by Phaedrux

                    @phaedrux said in No function after update:

                    ; Fans
                    M950 F0 C"out9" Q500 ; create fan 0 on pin out9 and set its frequency
                    M106 P0 S0 H T45 ; set fan 0 value. Thermostatic control is turned on

                    This M106 line should be M106 P0 S0 H-1

                    Can you also send M122 and M98 P"config.g" and post the results here?

                    Z-Bot CoreXY Build | Thingiverse Profile

                    1 Reply Last reply Reply Quote 0
                    • Wladekczundefined
                      Wladekcz
                      last edited by

                      @phaedrux said in No function after update:

                      M98 P"config.g"

                      In the old version, pressing G32 would start probing the table.
                      Give me an example of how T0 should look like.
                      The printer prints models, but it is not possible to withdraw or load the filament.

                      M122.txt
                      M98.txt
                      homeall.g

                      Władekcz

                      Phaedruxundefined 1 Reply Last reply Reply Quote 0
                      • Wladekczundefined
                        Wladekcz
                        last edited by

                        Should it be like that?

                        config.g modyfikacja1.txt

                        Władekcz

                        1 Reply Last reply Reply Quote 0
                        • Phaedruxundefined
                          Phaedrux Moderator @Wladekcz
                          last edited by

                          @wladekcz said in No function after update:

                          In the old version, pressing G32 would start probing the table.

                          Edit your bed.g and change the G29 command to G29 S1 and see if that makes a difference for you. Make sure the axis are homed first.

                          @wladekcz said in No function after update:

                          Give me an example of how T0 should look like.

                          T0 Nothing more.

                          Z-Bot CoreXY Build | Thingiverse Profile

                          1 Reply Last reply Reply Quote 0
                          • Wladekczundefined
                            Wladekcz
                            last edited by

                            T0 at the end of G-config helped. You can control the filament in the Extrusion Control window.
                            Changing the browser to Edge eliminated the problem with viewing the temperature. Thank you for your help.

                            Władekcz

                            1 Reply Last reply Reply Quote 1
                            • First post
                              Last post
                            Unless otherwise noted, all forum content is licensed under CC-BY-SA