CONSTANT AJAX disconnect errors

Jarery

DuetWiFiFirmware1.20alpha1+1

Install 6:55
idle
Disconnect 7:55

The log showed slightly different times. The disconnect happened at 7:55 but doesn't show on the log till 8:05. It would not connect via connect button during that time.
2017-10-12 06:56:11 Event logging started
2017-10-12 08:05:21 WiFi reported error: Lost connection, auto reconnecting
2017-10-12 08:05:22 WiFi reported error: Auto reconnect succeeded

after reconnect M122:
Network state is running
WiFi module is connected to access point
WiFi firmware version 1.20alpha1+1
WiFi MAC address a0:20:a6:10:55:89
WiFi Vcc 3.16, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 38352
WiFi IP address 192.168.2.32
WiFi signal strength -45dBm
Reconnections 1
HTTP sessions: 1 of 8
Socket states: 2 0 0 0 0 0 0 0
Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)

Edit 2:
Left idle it disconnected again, after waiting 30 min Im able to reconnect. Log doesn't show that it ever knew it was disconnected: The 10:10 log is me reconnecting after disconnecting 30 min or so previous
2017-10-12 06:56:11 Event logging started
2017-10-12 08:05:21 WiFi reported error: Lost connection, auto reconnecting
2017-10-12 08:05:22 WiFi reported error: Auto reconnect succeeded
2017-10-12 08:58:13 HTTP client 192.168.2.49 login succeeded
2017-10-12 10:10:20 HTTP client 192.168.2.49 login succeeded

Jarery

First print, disconnected while printing the skirt

dc42

Thanks for your feedback. Which country are you in?

Jarery

Canada, Vancouver BC specificaly,

KeeganB

Ill be away from the printer for about a week, but will updated to that new version you shared David as soon as I return.

fma

David, I juste realized that my WiFi signal strength is really low: -68dBm! I think I'm lucky it's working so well, despite such poor signal!

I think I will order the new ESP module, with antenna.

callil

Updated to alpha1+1 - pretty much the same story for me unfortunately.
The following log is right after a disconnect when idle. I restarted the wifi module with M552 on device.

[[language]]
=== Diagnostics ===
Used output buffers: 3 of 32 (17 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.20beta1 running on Duet WiFi 1.0
Board ID: 08DAM-9K9K2-NGNSN-6JKD0-3SJ6T-15UBM
Static ram used: 15128
Dynamic ram used: 96048
Recycled dynamic ram: 3512
Stack ram used: 1352 current, 4880 maximum
Never used ram: 11504
Last reset 00:06:35 ago, cause: reset button or watchdog
Last software reset reason: User, spinning module GCodes, available RAM 11504 bytes (slot 3)
Software reset code 0x0003, HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 41.1, current 41.6, max 42.8
Supply voltage: min 24.1, current 24.2, max 24.6, under voltage events: 0, over voltage events: 0
Driver 0: stalled standstill
Driver 1: stalled standstill
Driver 2: stalled standstill
Driver 3: standstill
Driver 4: standstill
Date/time: 2017-10-15 15:01:57
Slowest main loop (seconds): 0.008844; fastest: 0.000033
=== Move ===
MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heater = 0, chamber heater = -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.3
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is connected to access point 
WiFi firmware version 1.20alpha1+1
WiFi MAC address 5c:cf:7f:ef:4c:24
WiFi Vcc 3.11, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 35064
WiFi IP address 192.168.1.107
WiFi signal strength -58dBm
Reconnections 0
HTTP sessions: 1 of 8
Socket states: 2 0 0 0 0 0 0 0
Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)

JohnOCFII

I've been leery of updating beyond 1.18.2 due to the frequent reports of WiFi issues. Today I decided to take the leap. The upgrade to 1.19.2 went well. Checking M122 my RSSI varied between -53 and -58 (the access point is one floor away in a wood framed house). I stayed connected from a web browser (Google Chrome from a Mac) for approximately 4 hours. During the middle of that 4 hour window was a single 90 minute print.

All seemed good. Not posting to gloat - but just wanted to add some data points. My access point is an Asus router running the third party Asus-Merlin firmware.

John

Jarery

@JohnOCFII:

My access point is an Asus router running the third party Asus-Merlin firmware.

My setup is similar, albeit with the issues.
I have an Asus AC3100 as my main router about 3m away, and an AC66U about 12m away as an access point both with same firmware version, both Merlins.

sairon

I experienced the same issue on a new Duet Wifi I received this week. I recalled that I had similar problems with some devices in the past with WMM mode enabled on the router. And indeed, disabling it fixed the issue. I have a router running OpenWrt based distribution, which allows to enable/disable WMM on per-SSID basis. I'm not sure about other routers, such as those ASUS devices mentioned here, but I think it should be at least possible to toggle WMM globally to try if it solves the problem.

fma

As I use an OpenWRT-based router, I'll give this a try! Thanks.

JohnOCFII

@sairon:

I'm not sure about other routers, such as those ASUS devices mentioned here, but I think it should be at least possible to toggle WMM globally to try if it solves the problem.

Interesting.

One of my routers is an Asus RT-AC68P. The other is an older RT-N66R. The DuetWifi was attached to the RT-N66R. Both are running Asuswrt-Merlin 380.68_4

I notice on the Wireless section - Professional tab there is an item labeled: "Enable WMM APSD" The choices are "Enable" and "Disable" I'm not sure if they mean enabled and disabled but both routers are in the default setting, which shows "Enable."

Seeing that this setting has something to do with power saving mode and QoS, who knows - this could be related. I do not see a setting specific to just WMM.

https://routerguide.net/wmm-apsd-on-or-off/

John

sairon

@JohnOCFII:

Seeing that this setting has something to do with power saving mode and QoS, who knows - this could be related. I do not see a setting specific to just WMM.

Yep, "disabling WMM" practically means "disabling WMM APSD". Even the page you've linked mentions that it can be linked to connection dropouts: "There are reported cases of mobile devices dropping connections when the WMM APSD options are turned on."

As I said, it seems that disabling it resolved the issue for me, so it's worth a try if anyone faces the problem. Probably the worst thing that can happen is that they'll have worse battery performance on their mobile devices for the time of the test.

MiR

This article:

http://bbs.espressif.com/viewtopic.php?t=133

mentions a parameter for esp8266 to disable powersave on the chip itself, at least when in client-mode.

„You can use wifi_set_sleep_type to set sleep type for power saving and set NONE_SLEEP_T to disable power saving.“

@David: Could this be worth a try?

dc42

I looked at this before and I think it defaults to no power saving, but I'll check.

MiR

At least when I checked with sta_info about a week ago the module was reporting powersave capability to the AP

Jarery

turned off WMM APSD
So far 2 hours into a print. Not a definitive answer yet, but so far id say looks promising…
As I wrote this I went back and saw pink screen "ajax error" timeout, but was able to immediately reconnect with connect button.

Will continue testing

Edit: disconnected 5 min later, now can't reconnect....back to square one..

fma

I also turned off WMM. So far, no disconnect…

KeeganB

Im running a Tenda AC18 and it doesn't look like I have any WMM options, that I can find.

Jarery

I have the WMM turned off, and I continue to have the issues.
It does sound like the right path of investigation though.