• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Only probe where the part will be printed

Scheduled Pinned Locked Moved
General Discussion
8
51
3.5k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    RatRig0331 @dc42
    last edited by 14 Aug 2022, 15:55

    @dc42 not yet I’ll take a look

    1 Reply Last reply Reply Quote 0
    • undefined
      RatRig0331 @dc42
      last edited by 14 Aug 2022, 16:17

      @dc42 it looks like its all there in the gcode

      ; external perimeters extrusion width = 0.40mm
      ; perimeters extrusion width = 0.40mm
      ; infill extrusion width = 0.40mm
      ; solid infill extrusion width = 0.40mm
      ; top infill extrusion width = 0.40mm
      ; first layer extrusion width = 0.45mm

      M73 P0 R8
      M107
      M104 S205 ; set temperature
      ;TYPE:Custom
      set global.minProbeX = 183.982
      set global.maxProbeX = 316.018
      set global.minProbeY = 188.982
      set global.maxProbeY = 311.018
      T0 ; select tool 1
      M568 P0 R{heat.coldExtrudeTemperature+5} S205 A1 ; (set extruder to stanby to soften any protruding filament before probing )
      M106 P0 S0 ;Start with fan off
      M140 S68 R45; Set fast bed temp & standby - Standby is 20 degrees less than normal.
      M116 ; Wait for bed before doing mesh probe.
      M561 ; clear any bed transform
      G29 ; do mesh for printed area
      G29 S1 ; load small mesh
      G01 X0 Y{move.axes{1}.max} Z0.6 F1500 ; Move to back corner while heating
      M568 P0 R{heat.coldExtrudeTemperature+5} S205 A2 ; (set standby and active temperatures for active tool. Standby is 5 degrees above cold extrude temp )
      M116 ; Wait for all temps to stabilise
      M109 S205 ; set temperature and wait for it to be reached
      G21 ; set units to millimeters
      G90 ; use absolute coordinates
      M83 ; use relative distances for extrusion
      ; Filament gcode
      SET_GCODE_OFFSET Z=0
      SET_PRESSURE_ADVANCE ADVANCE=0.05
      M107
      ;LAYER_CHANGE
      ;Z:0.2
      ;HEIGHT:0.2
      ;BEFORE_LAYER_CHANGE
      ;0.2
      G92 E0
      ;

      this is what i changed in the mesh.g for my 500x500mm xycore

      ;0:/sys/mesh.g
      ; run when G29 with no paramters is called.
      ; if this file not found G29 S0 will run
      var m557MinX = 25; ; put your default here
      var m557MaxX = 450; ; put your default here
      var m557MinY = 25; ; put your default here
      var m557MaxY = 450; ; put your default here
      var MinSpace = 10 ; put default minimum spacing
      var MaxSpace = 30 ; put default maximum spacing
      var ProbeNumX = 8 ; put default probe points
      var ProbeNumY = 8 ; put default probe points.
      var ProbeCenterX = 285 ; will be updated to probe centre of print
      var ProbeCenterY = 270 ; will be updated to probe centre of print

      var MaxProbePoints = max(floor(move.axes[0].max / var.MaxSpace),floor(move.axes[1].max / var.MaxSpace)) ; maximum points in either axis

      echo "Maximum allowed probe points is " ^ var.MaxProbePoints ^ " using max space of " ^ var.MaxSpace
      var SafeZone = 3 ; safety margin for probing near edge.

      1 Reply Last reply Reply Quote 0
      • undefined
        OwenD @RatRig0331
        last edited by OwenD 14 Aug 2022, 19:34

        @ratrig0331
        Sounds like it's not finding a sensors.probe[0] when you run the initial setup from config.g
        As that line is at the start of the macro, it never gets to the lines that set the global variables up.
        Make sure your probe is configured before calling the macro.
        Maybe post you config.g so we can see how your probe(s) are configured

        undefined 3 Replies Last reply 14 Aug 2022, 20:03 Reply Quote 0
        • undefined
          RatRig0331 @OwenD
          last edited by 14 Aug 2022, 20:03

          @owend

          ​
          ;;; BLTouch ;;;
          M950 S0 C"io2.out" ; Create a servo pin on io2
          M558 P9 C"io2.in" H5 F240 T10800 A5 ; set Z probe type to unmodulated and the dive height + speeds
          G31 P25 X-29.00 Y-2.00 Z2.471

          undefined 1 Reply Last reply 14 Aug 2022, 20:51 Reply Quote 0
          • undefined
            RatRig0331 @OwenD
            last edited by 14 Aug 2022, 20:10

            @owend

            ​

            ;;; Endstops ;;;
            M574 X1 S1 P"io1.in" ; configure active high endstops
            M574 Y2 S1 P"io0.in" ; configure active high endstops
            M574 Z1 S2

            1 Reply Last reply Reply Quote 0
            • undefined
              OwenD @RatRig0331
              last edited by 14 Aug 2022, 20:51

              @ratrig0331
              Make sure
              M98 P"0:/sys/setDefaultProbePoints.g"
              Comes after your G31 in your BlTouch section

              undefined 3 Replies Last reply 14 Aug 2022, 21:16 Reply Quote 0
              • undefined
                RatRig0331 @OwenD
                last edited by 14 Aug 2022, 21:16

                @owend ok I’ll move it and give it a shot

                1 Reply Last reply Reply Quote 0
                • undefined
                  RatRig0331 @OwenD
                  last edited by 14 Aug 2022, 22:16

                  @owend that did the trick but now i need to turn down the amount of probe points
                  var MinSpace = 10 ; put default minimum spacing
                  var MaxSpace = 30 ; put default maximum spacing
                  var ProbeNumX = 8 ; put default probe points
                  var ProbeNumY = 8 ; put default probe points.
                  var ProbeCenterX = 285 ; will be updated to probe centre of print
                  var ProbeCenterY = 270 ; will be updated to probe centre of print

                  with my 100x100mm print its trying to do a 13x13 grid what do i tweak to lower that?

                  1 Reply Last reply Reply Quote 0
                  • undefined
                    RatRig0331 @OwenD
                    last edited by 15 Aug 2022, 02:19

                    @owend ok after letting it 100% there were more errors

                    8/14/2022, 10:15:03 PM Error: M557: bad grid definition: Spacing too small
                    8/14/2022, 10:14:19 PM Error: in GCode file line 773: G1: expected '}'

                    line 773 is your
                    G01 X0 Y{move.axes{1}.max} Z0.6 F1500 ; Move to back corner while heating

                    undefined 1 Reply Last reply 15 Aug 2022, 02:42 Reply Quote 0
                    • undefined
                      OwenD @RatRig0331
                      last edited by OwenD 15 Aug 2022, 02:42

                      @ratrig0331
                      Change your minSpace and maxSpace in the macro to reduce number of probe points
                      Try 50 & 100

                      The G1 is my bad
                      I did a search and replace when I was changing the braces, but changed one that should remain a square bracket

                      Change this line in superslicer
                      G01 X0 Y{"{move.axes{1}.max}"} Z0.6 F1500 ; Move to back corner while heating
                      To
                      G01 X0 Y{"{move.axes[1].max}"} Z0.6 F1500 ; Move to back corner while heating

                      Or delete the line if you don't want to move there while heating

                      undefined 1 Reply Last reply 15 Aug 2022, 10:56 Reply Quote 0
                      • undefined
                        RatRig0331 @OwenD
                        last edited by 15 Aug 2022, 10:56

                        @owend

                        One down one to go I’m still getting the m557 error with the 50/100 spacing will this be normal a normal error from down sizing the bed mesh or is there a fix

                        Error: M557: bad grid definition: Spacing too small

                        ——-Error: in GCode file line 773: G1: expected '}'———- is now fixed

                        undefined 1 Reply Last reply 15 Aug 2022, 11:06 Reply Quote 0
                        • undefined
                          jay_s_uk @RatRig0331
                          last edited by 15 Aug 2022, 11:06

                          @ratrig0331 the most probe points you can have on a duet 2 are 121 and on a duet 3 are 441

                          Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                          undefined 1 Reply Last reply 15 Aug 2022, 11:17 Reply Quote 0
                          • undefined
                            RatRig0331 @jay_s_uk
                            last edited by 15 Aug 2022, 11:17

                            @jay_s_uk too many points isn’t the issue I think, it must be too few points? With the settings first told to me it wanted to do a 13x12 grid on a 100mmx100mm print 156 points total, than I changed the min max to 50/100 and it only probed the middle and 4 conners and gave the same error

                            undefined undefined 2 Replies Last reply 15 Aug 2022, 11:27 Reply Quote 0
                            • undefined
                              OwenD @RatRig0331
                              last edited by OwenD 15 Aug 2022, 11:27

                              @ratrig0331

                              I believe the problem you are having is that I didn't allow for a probe that was offset to the other side of the extruder to mine.

                              Try these files.
                              I think it should sort it out.

                              ;setDefaultProbePoints.g - to be called from config.g after Z probe configuration section and any time defaults need to be reset.
                              var SafeZone = 10 ; probing won't be done closer than this amount from bed edge - adjust as required
                              var defaultProbeSpacing = 50 ; default mesh grid spacing in mm - adjust as required
                              ; shouldn't need to edit after here
                              var MinReachableX = max(0,sensors.probes[0].offsets[0]) + var.SafeZone
                              var MaxReachabeX = move.axes[0].max - abs(sensors.probes[0].offsets[0]) - var.SafeZone
                              var MinReachableY = max(0,sensors.probes[0].offsets[1]) + var.SafeZone
                              var MaxReachabeY = move.axes[1].max - abs(sensors.probes[0].offsets[1]) - var.SafeZone
                              M557 X{var.MinReachableX,var.MaxReachabeX} Y{var.MinReachableY,var.MaxReachabeY} S{var.defaultProbeSpacing}; define mesh grid
                              ;echo "M557 X"^{var.MinReachableX}^","^{var.MaxReachabeX}, "Y"^{var.MinReachableY}^","^{var.MaxReachabeY}, "S"^{var.defaultProbeSpacing}
                              if !exists(global.minProbeX)
                              global minProbeX = move.compensation.probeGrid.mins[0]
                              else
                              set global.minProbeX = move.compensation.probeGrid.mins[0]
                              if !exists(global.minProbeY)
                              global minProbeY = move.compensation.probeGrid.mins[1]
                              else
                              set global.minProbeY = move.compensation.probeGrid.mins[1]
                              if !exists(global.maxProbeX)
                              global maxProbeX = move.compensation.probeGrid.maxs[0]
                              else
                              set global.maxProbeX = move.compensation.probeGrid.maxs[0]
                              if !exists(global.maxProbeY)
                              global maxProbeY = move.compensation.probeGrid.maxs[1]
                              else
                              set global.maxProbeX = move.compensation.probeGrid.maxs[1]

                              revised mesh.g

                              ;0:/sys/mesh.g
                              ; run when G29 with no paramters is called.
                              ; if this file not found G29 S0 will run
                              var SafeZone = 3 ; safety margin for probing near edge.
                              var MinSpace = 20 ; put default minimum spacing
                              var MaxSpace = 60 ; put default maximum spacing
                              ; these values are place holders aand will be calculated later
                              var m557MinX = 40; ; put your default here
                              var m557MaxX = 180; ; put your default here
                              var m557MinY = 20; ; put your default here
                              var m557MaxY = 180; ; put your default here
                              var ProbeCenterX = 90 ; will be updated to probe centre of print
                              var ProbeCenterY = 90 ; will be updated to probe centre of print
                              var ProbeNumX = 8 ; put default number of probe points
                              var ProbeNumY = 8 ; put default number probe points.
                              var MaxProbePoints = max(floor(move.axes[0].max / var.MaxSpace),floor(move.axes[1].max / var.MaxSpace)) ; maximum points in either axis
                              ;echo "Maximum allowed probe points is " ^ var.MaxProbePoints ^ " using max space of " ^ var.MaxSpace
                              if exists(global.minProbeX)
                              if global.minProbeX < max(0,sensors.probes[0].offsets[0]) + var.SafeZone
                              echo "minProbeX (" ^ global.minProbeX ^ ") unreachable - reset to " ^ (sensors.probes[0].offsets[0] + var.SafeZone)
                              set global.minProbeX = max(0,sensors.probes[0].offsets[0]) + var.SafeZone
                              set var.m557MinX = global.minProbeX
                              if exists(global.maxProbeX)
                              if global.maxProbeX < (global.minProbeX + (var.MinSpace*2))
                              set global.maxProbeX = (global.minProbeX + (var.MinSpace*2))
                              if global.maxProbeX > (move.axes[0].max - abs(sensors.probes[0].offsets[0]) - var.SafeZone)
                              echo "maxProbeX (" ^ global.maxProbeX ^ ") unreachable - reset to " ^ (move.axes[0].max - sensors.probes[0].offsets[0] - var.SafeZone)
                              set global.maxProbeX = move.axes[0].max - abs(sensors.probes[0].offsets[0]) - var.SafeZone
                              set var.m557MaxX = global.maxProbeX
                              if exists(global.minProbeY)
                              if global.minProbeY < max(0,sensors.probes[0].offsets[1]) + var.SafeZone
                              echo "minProbeY (" ^ global.minProbeY ^ ") unreachable - reset to " ^ (sensors.probes[0].offsets[1] + var.SafeZone)
                              set global.minProbeY = max(0,sensors.probes[0].offsets[1]) + var.SafeZone
                              set var.m557MinY = global.minProbeY
                              if exists(global.maxProbeY)
                              if global.maxProbeY < (global.minProbeY + (var.MinSpace*2))
                              set global.maxProbeY = (global.minProbeY + (var.MinSpace*2))
                              if global.maxProbeY > (move.axes[1].max - abs(sensors.probes[0].offsets[1]) - var.SafeZone)
                              echo "maxProbeY (" ^ global.maxProbeY ^ ") unreachable - reset to " ^ (move.axes[1].max - sensors.probes[0].offsets[1] - var.SafeZone)
                              set global.maxProbeY = (move.axes[1].max - abs(sensors.probes[0].offsets[1]) - var.SafeZone)
                              set var.m557MaxY = global.maxProbeY
                              echo "Probing grid - X" ^ var.m557MinX ^ ":" ^ var.m557MaxX ^ " Y" ^ var.m557MinY ^ ":" ^ var.m557MaxY
                              var MinProbesX = floor((var.m557MaxX - var.m557MinX) / var.MaxSpace)
                              ;echo "Min Probes X is " ^ var.MinProbesX
                              var MaxProbesX = floor((var.m557MaxX - var.m557MinX) / var.MinSpace)
                              ;echo "Max Probes X is " ^ var.MaxProbesX
                              set var.ProbeNumX = min(var.MaxProbePoints,var.MaxProbesX)
                              var MinProbesY = floor((var.m557MaxY - var.m557MinY) / var.MaxSpace)
                              ;echo "Min Probes Y is " ^ var.MinProbesY
                              var MaxProbesY = floor((var.m557MaxY - var.m557MinY) / var.MinSpace)
                              ;echo "Max Probes Y is " ^ var.MaxProbesY
                              set var.ProbeNumY = min(var.MaxProbePoints,var.MaxProbesY)
                              ; sanity check probe points
                              if var.ProbeNumX<2
                              set var.ProbeNumX=2
                              if var.ProbeNumY<2
                              set var.ProbeNumY=2
                              if var.ProbeNumX > var.MaxProbePoints
                              set var.ProbeNumX = var.MaxProbePoints
                              if var.ProbeNumY > var.MaxProbePoints
                              set var.ProbeNumY = var.MaxProbePoints
                              if (var.ProbeNumX * var.ProbeNumY) > 441
                              if var.ProbeNumX > 21
                              set var.ProbeNumX = 21
                              echo "Too many X points - reduced to 21"
                              if var.ProbeNumY > 21
                              set var.ProbeNumY = 21
                              echo "Too many Y points - reduced to 21"
                              echo "Probing " ^ var.ProbeNumX ^ " points in X direction & " ^ var.ProbeNumY ^ " points in Y direction"
                              ;check state of heaters
                              var bedState = heat.heaters[0].state
                              var bedActiveTemp = heat.heaters[0].active
                              var bedStandbyTemp = heat.heaters[0].standby
                              var nozzleState = heat.heaters[1].state
                              M140 P0 S-276 ; turn off bed heater
                              M568 P0 A0 ; turn off nozzle heater
                              ; do probing
                              set var.ProbeCenterX = (global.maxProbeX - ((global.maxProbeX - global.minProbeX)/2)) ; calculate centre point of probe area
                              set var.ProbeCenterY = (global.maxProbeY - ((global.maxProbeY - global.minProbeY)/2)) ; calculate centre point of probe area
                              echo "Setting Z datum point at X" ^ var.ProbeCenterX ^ " Y" ^ var.ProbeCenterY
                              ; set Z = 0 to centre of probe area
                              G1 X{var.ProbeCenterX- sensors.probes[0].offsets[0]} Y{var.ProbeCenterY- sensors.probes[0].offsets[1]} Z{sensors.probes[0].diveHeight+2} F3600
                              G30
                              echo "Mesh probing"
                              M557 X{var.m557MinX,var.m557MaxX} Y{var.m557MinY,var.m557MaxY} P{var.ProbeNumX,var.ProbeNumY}
                              if result != 0
                              abort "ERROR: could not create mesh"
                              else
                              G29 S0
                              if result != 0
                              abort "ERROR: Mesh probing failed"
                              else
                              echo "Mesh probing successful. Loading mesh.."
                              ; set Z = 0 to centre of probe area
                              echo "Reset Z datum in mesh centre"
                              G1 X{var.ProbeCenterX - sensors.probes[0].offsets[0]} Y{var.ProbeCenterY - sensors.probes[0].offsets[1]} Z{sensors.probes[0].diveHeight+2} F3600
                              G30
                              ; turn the heaters back on if needed
                              if var.bedState != "off"
                              M140 S{var.bedActiveTemp} R{var.bedStandbyTemp}
                              if var.bedState="active"
                              M144 P0 S1 ; put bed on active temp
                              else
                              M144 P0 S0 ; put bed on standby temp
                              if var.nozzleState != "off"
                              if var.nozzleState = "active"
                              M568 P0 A2 ; set nozzle to active
                              else
                              M568 P0 A1 ; set nozzle to standby
                              1 Reply Last reply Reply Quote 1
                              • undefined
                                dc42 administrators @RatRig0331
                                last edited by dc42 15 Aug 2022, 12:34

                                @ratrig0331 the minimum spacing between points allowed is 0.1mm in each of X and Y. "Spacing too small" means you have tried to specify a smaller spacing than that.

                                Duet WiFi hardware designer and firmware engineer
                                Please do not ask me for Duet support via PM or email, use the forum
                                http://www.escher3d.com, https://miscsolutions.wordpress.com

                                undefined 1 Reply Last reply 15 Aug 2022, 20:24 Reply Quote 1
                                • undefined
                                  OwenD @dc42
                                  last edited by 15 Aug 2022, 20:24

                                  @dc42 said in Only probe where the part will be printed:

                                  the minimum spacing between points allowed is 0.1mm in each of X and Y. "Spacing too small" means you have tried to specify a smaller spacing than that.

                                  In that case I'm at a bit of a loss how @RatRig0331 is getting that error using my code.
                                  It's early morning here (Australia) and I have to go to work, so I can't look at till I get home.
                                  @RatRig0331 Can you please un-comment all the lines in the mesh.g that show the calculations and post the output from the console.

                                  At the start I work out the maximum possible number of probes if a full bed was done using maxSpace.
                                  Later I use the object size to recalculate the number of probes also using maxSpacing.
                                  The lesser of these two numbers is used (or should be).

                                  There must be a fundamental flaw in my logic (at least with your bed size and probe configuration). 😕

                                  It also occurs to me that I haven't catered for deltas or printers where X0, Y0 is in the center of the bed.

                                  undefined 2 Replies Last reply 16 Aug 2022, 00:07 Reply Quote 1
                                  • undefined
                                    RatRig0331 @OwenD
                                    last edited by 16 Aug 2022, 00:07

                                    @owend

                                    8/15/2022, 8:04:58 PM Error: M557: bad grid definition: Spacing too small
                                    8/15/2022, 8:04:26 PM Reset Z datum in mesh centre
                                    8/15/2022, 8:04:26 PM Mesh probing successful. Loading mesh..
                                    8/15/2022, 8:04:26 PM 36 points probed, min error -0.141, max error 0.093, mean -0.020, deviation 0.066
                                    Height map saved to file 0:/sys/heightmap.csv
                                    8/15/2022, 8:01:59 PM Mesh probing
                                    8/15/2022, 8:01:50 PM Setting Z datum point at X250.0000 Y250.0000
                                    8/15/2022, 8:01:50 PM Probing 6 points in X direction & 6 points in Y direction
                                    8/15/2022, 8:01:50 PM Probing grid - X183.907:316.093 Y188.907:311.093
                                    8/15/2022, 8:01:32 PM Leadscrew adjustments made: -0.014 0.008 0.009, points used 3, (mean, deviation) before (0.001, 0.010) after (-0.000, 0.000)
                                    8/15/2022, 8:01:12 PM Leadscrew adjustments made: 0.015 0.022 0.001, points used 3, (mean, deviation) before (0.014, 0.008) after (-0.000, 0.000)
                                    8/15/2022, 8:00:52 PM Leadscrew adjustments made: 0.102 0.033 -0.002, points used 3, (mean, deviation) before (0.046, 0.040) after (0.000, 0.000)
                                    8/15/2022, 8:00:32 PM Leadscrew adjustments made: 0.503 0.279 0.452, points used 3, (mean, deviation) before (0.404, 0.087) after (-0.000, 0.000)
                                    8/15/2022, 7:58:35 PM M32 "0:/gcodes/First_Layer_Test_0.2mm_PLA_10mhhhhhhhhhhhhhh.gcode"
                                    File 0:/gcodes/First_Layer_Test_0.2mm_PLA_10mhhhhhhhhhhhhhh.gcode selected for printing

                                    1 Reply Last reply Reply Quote 0
                                    • undefined
                                      RatRig0331 @OwenD
                                      last edited by 16 Aug 2022, 00:22

                                      @owend

                                      8/15/2022, 8:17:42 PM Error: M557: bad grid definition: Spacing too small
                                      8/15/2022, 8:17:10 PM Reset Z datum in mesh centre
                                      8/15/2022, 8:17:10 PM Mesh probing successful. Loading mesh..
                                      8/15/2022, 8:17:10 PM 36 points probed, min error -0.105, max error 0.079, mean -0.005, deviation 0.044
                                      Height map saved to file 0:/sys/heightmap.csv
                                      8/15/2022, 8:14:43 PM Mesh probing
                                      8/15/2022, 8:14:34 PM Setting Z datum point at X250.0000 Y250.0000
                                      8/15/2022, 8:14:34 PM Probing 6 points in X direction & 6 points in Y direction
                                      8/15/2022, 8:14:34 PM Max Probes Y is 6
                                      8/15/2022, 8:14:34 PM Min Probes Y is 2
                                      8/15/2022, 8:14:34 PM Max Probes X is 6
                                      8/15/2022, 8:14:34 PM Min Probes X is 2
                                      8/15/2022, 8:14:34 PM Probing grid - X183.907:316.093 Y188.907:311.093
                                      8/15/2022, 8:14:34 PM Maximum allowed probe points is 8 using max space of 60
                                      8/15/2022, 8:14:16 PM Leadscrew adjustments made: 0.002 0.008 0.006, points used 3, (mean, deviation) before (0.005, 0.002) after (0.000, 0.000)
                                      8/15/2022, 8:13:56 PM Leadscrew adjustments made: 0.016 0.016 0.011, points used 3, (mean, deviation) before (0.015, 0.002) after (0.000, 0.000)
                                      8/15/2022, 8:13:36 PM Leadscrew adjustments made: 0.168 0.055 0.022, points used 3, (mean, deviation) before (0.084, 0.057) after (-0.000, 0.000)
                                      8/15/2022, 8:13:16 PM Leadscrew adjustments made: 0.413 0.322 0.388, points used 3, (mean, deviation) before (0.372, 0.035) after (0.000, 0.000)
                                      8/15/2022, 8:12:01 PM M32 "0:/gcodes/First_Layer_Test_0.2mm_PLA_10mhhhhhhhhhhhhhh.gcode"
                                      File 0:/gcodes/First_Layer_Test_0.2mm_PLA_10mhhhhhhhhhhhhhh.gcode selected for printing

                                      undefined 1 Reply Last reply 16 Aug 2022, 00:43 Reply Quote 0
                                      • undefined
                                        OwenD @RatRig0331
                                        last edited by 16 Aug 2022, 00:43

                                        @ratrig0331
                                        The M557 that is causing the error seems to be well after all the stuff I did.
                                        Check for an M557 somewhere else in your slicer start gcode

                                        undefined 2 Replies Last reply 16 Aug 2022, 01:27 Reply Quote 0
                                        • undefined
                                          RatRig0331 @OwenD
                                          last edited by 16 Aug 2022, 01:27

                                          @owend

                                          your right sorry it was in my start code purge line for some reason thank you so much for your time and patients with me this is all still vary new to me

                                          8/15/2022, 9:22:31 PM Reset Z datum in mesh centre
                                          8/15/2022, 9:22:31 PM Mesh probing successful. Loading mesh..
                                          8/15/2022, 9:22:31 PM 36 points probed, min error -0.174, max error 0.083, mean -0.012, deviation 0.067
                                          Height map saved to file 0:/sys/heightmap.csv
                                          8/15/2022, 9:20:04 PM Mesh probing
                                          8/15/2022, 9:19:56 PM Setting Z datum point at X250.0000 Y250.0000
                                          8/15/2022, 9:19:55 PM Probing 6 points in X direction & 6 points in Y direction
                                          8/15/2022, 9:19:55 PM Max Probes Y is 6
                                          8/15/2022, 9:19:55 PM Min Probes Y is 2
                                          8/15/2022, 9:19:55 PM Max Probes X is 6
                                          8/15/2022, 9:19:55 PM Min Probes X is 2
                                          8/15/2022, 9:19:55 PM Probing grid - X183.907:316.093 Y188.907:311.093
                                          8/15/2022, 9:19:55 PM Maximum allowed probe points is 8 using max space of 60
                                          8/15/2022, 9:19:55 PM Leadscrew adjustments made: -0.003 0.011 0.016, points used 3, (mean, deviation) before (0.007, 0.007) after (-0.000, 0.000)
                                          8/15/2022, 9:19:34 PM Leadscrew adjustments made: 0.006 -0.003 0.004, points used 3, (mean, deviation) before (0.002, 0.003) after (0.000, 0.000)
                                          8/15/2022, 9:19:14 PM Leadscrew adjustments made: 0.046 0.021 0.031, points used 3, (mean, deviation) before (0.032, 0.009) after (-0.000, 0.000)
                                          8/15/2022, 9:18:54 PM Leadscrew adjustments made: -0.011 0.368 0.277, points used 3, (mean, deviation) before (0.213, 0.149) after (-0.000, 0.000)

                                          1 Reply Last reply Reply Quote 0
                                          19 out of 51
                                          • First post
                                            19/51
                                            Last post
                                          Unless otherwise noted, all forum content is licensed under CC-BY-SA