Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Help for a newbe to build firmware and install DWC

    Scheduled Pinned Locked Moved
    General Discussion
    3
    21
    586
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • TimV 0undefined
      TimV 0 @Phaedrux
      last edited by

      @Phaedrux I am working through your suggestions. I thought it would be helpful to post the config that you asked for.config.g

      TimV 0undefined 1 Reply Last reply Reply Quote 0
      • TimV 0undefined
        TimV 0 @TimV 0
        last edited by

        @TimV-0 I updated the www folder files
        Used 552 to connect to WIFI
        Gcodes one step at a time
        Confirmed it found my network
        Confirmed it connected to the network
        Confirmed I received an IP address
        Http://192.168.2.90
        Your Duet rejected the HTTP request: page not found

         Check that the SD card is mounted and has the correct files in its /www folder
        

        http://DuetTest.local
        Your Duet rejected the HTTP request: page not found

         Check that the SD card is mounted and has the correct files in its /www folder
        

        Since I am working with copied files, I have a feeling I should extract the files in the folders on the SD card. The unzip process only unzipped the original .zip level and not the files in the folders

        TimV 0undefined 1 Reply Last reply Reply Quote 0
        • TimV 0undefined
          TimV 0 @TimV 0
          last edited by

          @TimV-0 Went through and unzipped all the zip files on the SD card
          Made no difference

          TimV 0undefined 1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator
            last edited by

            You only need to extract the main zip file. all the files within the WWW folder should be left as is.

            What IP address does your computer have?

            Can you send M122 over USB terminal and copy and paste the results here?

            Can you share a screen shot of the contents of your SD card root and the www folder?

            Z-Bot CoreXY Build | Thingiverse Profile

            TimV 0undefined 1 Reply Last reply Reply Quote 0
            • TimV 0undefined
              TimV 0 @Phaedrux
              last edited by

              @Phaedrux
              TV M122.txt

              There have been discoveries since my first post
              My sys and WWW folders had been duplicated inside the folder. Stupid me - Fixed

              On power applied, the printer will not appear as live on the network in Angry IP Scanner scan data

              If I use gcodes:
              M550= RepRap name: My Duet
              M552= Wifi Module is Disabled
              M552 S1= Wifi module started Wifi module is connected to access point "correct name is showing"
              IP address "correct address is showing"

              After the above gcodes Angry IP Scanner Scan reports:
              Printer is Live
              Hostname: myduet.local
              Port: 80
              Ping 7ms
              Mac Address 84:::::** (I'm sure it is correct)
              NetBios Info is blank (nothing listed)

              Top right corner of PanelDue shows "Connecting" even though I completed the M500 sequence above

              TimV 0undefined 1 Reply Last reply Reply Quote 0
              • TimV 0undefined
                TimV 0 @TimV 0
                last edited by

                This post is deleted!
                1 Reply Last reply Reply Quote 0
                • TimV 0undefined
                  TimV 0 @TimV 0
                  last edited by

                  @TimV-0 Root.png

                  1 Reply Last reply Reply Quote 0
                  • TimV 0undefined
                    TimV 0
                    last edited by

                    Root.png WWW.png

                    1 Reply Last reply Reply Quote 0
                    • Phaedruxundefined
                      Phaedrux Moderator
                      last edited by

                      @TimV-0 said in Help for a newbe to build firmware and install DWC:

                      Top right corner of PanelDue shows "Connecting" even though I completed the M500 sequence above

                      What M500 sequence do you mean?

                      The PanelDue will need an up to date firmware version, and will need to be enabled with a command in config.g to connect. M575 P1 B57600 S1

                      Are you now able to ping the duet from your pc? Are your IP addresses in the same subnet?

                      [Warning: Maximal number of characters per line exceeded! Check the line break settings in Terminal > Settings > Text or increase the limit in Terminal > Settings > Advanced.]

                      You'll need to change your line ending settings in YAT to get the complete M122 report.

                      yat.png

                      Z-Bot CoreXY Build | Thingiverse Profile

                      TimV 0undefined 1 Reply Last reply Reply Quote 0
                      • TimV 0undefined
                        TimV 0 @Phaedrux
                        last edited by

                        @Phaedrux Hi: sequence was M550, M552, M552 s1, from my earlier post which detailed the results from these codes as well; manually detailing the results to indicate that if I just turn the machine on, it does not connect to the network.

                        The paneldue was included when I ran the configure utlility. I will verify config, but I don't recall ever putting in the m575.

                        I did just run a ping test after M552, M552 s1, because having just turned the printer on, it did not automatically connect to the network

                        Now that it actually is on the net, I can Ping it just fine. 7ms or lower

                        Yes, all of my network is on one subnet. I was able to ping the printer from a computer in a different room. (Mac Mini M1)

                        I tried to follow the instructions for installing the firmware from the Apple onto the printer using usb, but it was a terrible process and it did not work

                        Thanks for the info on setting up Yat.

                        1 Reply Last reply Reply Quote 0
                        • Phaedruxundefined
                          Phaedrux Moderator
                          last edited by

                          It would be good to see the contents of your config.g and the full M122 report.

                          Z-Bot CoreXY Build | Thingiverse Profile

                          TimV 0undefined 3 Replies Last reply Reply Quote 0
                          • TimV 0undefined
                            TimV 0 @Phaedrux
                            last edited by

                            @Phaedrux config.g

                            TimV 0undefined 1 Reply Last reply Reply Quote 0
                            • TimV 0undefined
                              TimV 0 @TimV 0
                              last edited by

                              @TimV-0 M122.txt

                              1 Reply Last reply Reply Quote 0
                              • TimV 0undefined
                                TimV 0 @Phaedrux
                                last edited by

                                @Phaedrux This morning I reformatted my sd card and copied the files that were created the configuration software on version 3.4.4.

                                I connected my usb cable and it magically started running up config.g. I'm going to check. Something looks like it failed on the network connection. I copied this from the terminal window.

                                RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.3
                                Executing config.g... HTTP is enabled on port 80
                                FTP is disabled
                                TELNET is disabled
                                Warning: Macro file config-override.g not found
                                Done!
                                Executing runonce.g... WiFi module started
                                Error: Failed to add SSID to remembered list: SPI timeout
                                Done!

                                My IP did not show in the angry ip scan

                                1 Reply Last reply Reply Quote 0
                                • TimV 0undefined
                                  TimV 0 @Phaedrux
                                  last edited by

                                  @Phaedrux
                                  Thank you, thank you, thank you!

                                  I manually issued M552, M552 S1, M550

                                  The name I used actually showed up for the first time.

                                  http://192.168.2.90 connected to the printer an DWC automatically opened.

                                  Could it have been that I did not use the official formatting utility until this morning?

                                  I also had wired up the ender5 endstops which are the outside two terminals on the endstop, but terminate to a 2 pin connector for the board end. I replaced the cables with cables that are 3 pin at both ends.

                                  I think my endstops were shorted on the board. I now have a red light beside each motor connection on the Duet

                                  1 Reply Last reply Reply Quote 0
                                  • Phaedruxundefined
                                    Phaedrux Moderator
                                    last edited by

                                    Yes incorrectly wired endstops could cause the board to reset.

                                    Your config looks ok to start the wifi module on startup.

                                    Send M587 by itself in the console to see what wifi SSIDs are currently saved. Ideally there should be only 1.

                                    Z-Bot CoreXY Build | Thingiverse Profile

                                    1 Reply Last reply Reply Quote 0
                                    • First post
                                      Last post
                                    Unless otherwise noted, all forum content is licensed under CC-BY-SA