Stall detection and sensorless homing

fma

I'm making some sensorless homing tests, and it works great!

However, I'm using a CoreXY, and unlike sensor homing, when I launch a diagonal move, with something like:

G1 X325 Y325 F3600

both motors stop as soon as stall is detected on one of them. Is it what the code does, or is it because stall of one motor influence the other? In the first case, could it be possible to have the same behavior as sensor homing, and in the second case, what can I do to fix that?

Thanks.

fma

My bad! I forgot the specific procedure on the CoreXY homing…

Here is my setup:

M400                  ; make sure everything has stopped before we make changes
M574 X2 Y2 S3         ; set endstops to use motor stall
M913 X50 Y50          ; drop motor currents to 50%
M915 X Y S2 R0 F0     ; set X and Y to sensitivity 2, do nothing when stall, unfiltered
G91                   ; use relative positioning
G1 Z10 F1200          ; lift Z

G1 S1 X325 Y325 F3600 ; move right/back 325mm, stopping at the endstop
G1 X-5 Y-5            ; move away from end
M915 X Y S-2 R0 F0    ; increase sensitivity
G1 S1 X325 F3600      ; move right 325mm, stopping at the endstop
G1 S1 Y325 F3600      ; move back 325mm, stopping at the endstop
G1 X-5 Y-5            ; move away from end

G1 Z-10 F1200         ; lower Z
M400                  ; make sure everything has stopped before we reset the motor currents
G90                   ; back to absolute positioning
M913 X100 Y100        ; motor currents back to 100%
M574 X1 Y1 S1         ; define active low microswitches

As you can see, I changed the sensitivity, because I noticed the stall detection is not the same when both motors run, or only one. With this settings, the homing is very smooth, no noise when hitting walls.

fma

Mmm, this is not that simple. There are very large variations between motors cold and motors hot. So I have to decrease the sensitivity, or I get false detection. But then, the choc is more important when hitting walls

I will try to change (reduce) the motor current between the first homing (diagonally, -> only 1 motor running), and the second and third (X or Y -> 2 motors running)…

David, I'm wondering: during a X or Y move, do you wait for both motors to stall to consider at endstop, or any of them?

dc42

I wasn't expecting CoreXY users to use sensorless homing. The way it will work at present is that during the initial G1 X Y move, if either motor stalls then the whole move will be stopped. In the subsequent G1 X move, only the X motor will be monitored, and in the G1 Y move only the Y motor will be monitored. Obviously it would make sense to monitor both motors for all three moves.

I think it's the case that the lower you set the M915 S parameter, the more sensitive the stall detection will be to temperature.

fma

Do you plan to monitor both motors in a future release?

dc42

If it's easy to do then I'll include it in the next beta.

fma

Thanks!

DjDemonD

I did give this a try on my corexy yesterday I used your x homing gcode Frédéric, and modified it for y as well. I had to turn my sensitivity up to 7 for x and 8 for y but it did work. Not very reliably sometimes I got false triggers, if I went as high as 13 on sensitivity it crashed the end of the travel pretty hard and didn't trigger.

So cool idea but I'm sticking with endstops for now.

DjDemonD

@dc42:

I wasn't expecting CoreXY users to use sensorless homing.

Thanks for doing this David it is quite a nice feature to play with, but if a corexy is a 2-motors-linked-kinematic and a delta is 3-motors-linked, can this be used for deltas? Or is it actually easier as there is one endstop per tower and one motor it controls?

I wouldn't use it on the kossel Xl as my optical endstops are very accurate probably better than the 4 steps resolution. But I'd like to try making a delta from a tube which was discussed on reprap, and an endstop-less scheme appeals.

dc42

Yes deltas are easier because each tower has one motor and one endstop. I had it working well on my delta, although I wouldn't rely on it without doing an auto calibration cycle after homing.

For sensorless homing on a delta, I suggest putting the motors at the top and making the physical endstop adjustable with a range of at least 4 full steps. That way, the belt distance between the motor pulley and the carriage when homed will be small, so thermal expansion shouldn't change the homed motor position by as much as a full step. If it turns out that the homing position is on the cusp between full steps, you can adjust the physical endstop position to avoid that.

Just about any type of endstop switch should have resolution way better than 1 full step.

MortarArt

This might be a particularly helpful feature for CoreXY printers that plan to implement parked effectors!

totalitarian

Hmm, could we use stall detection as a z probe? Or would it be too aggressive?

deckingman

@totalitarian:

Hmm, could we use stall detection as a z probe? Or would it be too aggressive?

I think David answered this elsewhere. Z axes are typically screw driven so even for homing against a hard stop, it's unlikely that the sensitivity could be adjusted to accurately discriminate. So with probing I'd say thee is zero chance of getting the necessary precision and repeatability.

totalitarian

Fair enough. Would have been a sweet way to level a bed So, if we already have x/y endstops, is there any advantage to sensor-less homing?

deckingman

@totalitarian:

Fair enough. Would have been a sweet way to level a bed So, if we already have x/y endstops, is there any advantage to sensor-less homing?

I personally wouldn't want to rely on it. Even if I was starting a build from scratch, I'd still fit switches. Simple micro switches are cheap and reliable.

dc42

In view of the limitations (in particular, limited accuracy) of sensorless homing, IMO it is a reasonable option for minimum-cost printers, and little more than a gimmick on anything else. The current Duets are over-specified and too expensive to be used in low cost printers.

S1lencer

Hey i have a question regarding the stall detection, how can i tell the printer to rehome after a stall was detected?

fma

See https://www.duet3d.com/wiki/Stall_detection_and_sensorless_homing

Use M915 with R param = 3.

S1lencer

Thank you

SuperJETT

I view sensorless homing for X/Y as a "nice" feature where I can eliminate some wiring on my coreXY, particularly since the X switch was on the carriage. Because it was there, it's also one less thing to design my extruder mount around.