New Printer but Stepper does not run

gringo

Hello,
after I finished building my printer, I did the configuration with the RepRapconfigtool.
I tried to create a move with M564 H0 and G0 X10 or Y10 or Z10. The steppers just rattle
For X and Y I have steppers with 0.9 angle the 3 Z steppers have 1.8 angle.
I use a Duet3 6HC and need help please.

;===============================================================================================================
; Drives
;===============================================================================================================
M569 P0.0 S1                                              ; physical drive 0.0 goes forwards --X - Achse
M569 P0.1 S1                                              ; physical drive 0.1 goes forwards --Y - Achse
M569 P0.2 S1                                              ; physical drive 0.2 goes forwards --Z Motor vorne links
M569 P0.5 S1                                              ; physical drive 0.5 goes forwards --Z Motor hinten mitte
M569 P0.4 S1                                              ; physical drive 0.4 goes forwards --Z Motor vorne rechts
M569 P0.3 S1                                              ; physical drive 0.3 goes forwards --Extruder

M584 X0.0 Y0.1 Z0.2:0.5:0.4 E0.3                          ; set drive mapping
M671 X0:165:330 Y0:330:0 S10                              ; Positionen der Trapezgewindespindel für das Bed Leveling
M350 X16 Y16 Z16 E16 I1                                   ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z400.00 E420.00                        ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00                       ; set maximum instantaneous speed changes (mm/min)
M203 X200.00 Y200.00 Z250.00 E1200.00                     ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z20.00 E250.00                     ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z800 E800 I30                            ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                                   ; Set idle timeout
;===============================================================================================================
; Axis Limits
;===============================================================================================================
M208 X0 Y0 Z0 S1                                          ; set axis minima
M208 X330 Y330 Z350 S0                                    ; set axis maxima
;===============================================================================================================

Phaedrux

Please post your full config.g.
Also send M122 and M98 P"config.g" in the gcode console and copy and paste the results here.
Do you get any error messages?

gringo

I get no errors.

infiniteloop

@gringo

I get no errors.

Fine for you. Pro-tip on how to interpret @Phaedrux’s posts: never ignore all lines but the last one

gringo

@infiniteloop

thanks for helping me.
Pro tip for you: Keep comments like that to yourself.

@Phaedrux
Posting the results later.

gringo

I have found the error. The color coding of the stepper cables did not match that of the Duet.
I had connected black/black, green/green, blue/blue, red/red.
But it must be black/black, green/red, blue/blue red/green.

dc42

@gringo said in New Printer but Stepper does not run:

The color coding of the stepper cables did not match that of the Duet.

Did your motor have detachable cables? This is a common issue when the motor has detachable cables. See https://docs.duet3d.com/en/User_manual/Connecting_hardware/Motors_connecting#using-the-internal-drivers.

gringo

@dc42

Yes,I’m using E3D Stepper