6 axis delta 3D printer
-
Does anyone know where I can find 3D models of these Kossel vertex and carriage?
https://www.robotdigg.com/product/555/2040-or-3030-Alu-Vertex-for-Kossel-XXL-or-XXXL
https://www.robotdigg.com/product/495/Carriage-for-open-ended-beltThanks!
-
@fma said in 6 axis delta 3D printer:
Kossel vertex and carriage
Hi @fma, I have the basic vertex models for the Robotdigg 2040 corners in Fusion360 format as was taking advantage of lots of quiet-time with lockdown to learn the product. Let me know if any use. Re the comment above on strength of the magballs/arms - I am just working though doubling up to 12-arms as need to support a Nema17 for my Clay extruder, six arms just about worked but would one would occasionally snap off when starting.
Not the cheapest solution, but I wanted the ease of magnetic attachment as need to remove the extruder for cleaning after prints. Should know in next couple of weeks how it goes.
-
Just to chime in my experience with inexpensive linear rails as another anecdote : The rails themselves were fine. It took some work on the carriage blocks to make the difference over delrin-covered ball bearing solutions I was looking for.
I had to adjust the retaining wires to line up properly for the rails. This was the WORST part since that stupid wire is in the middle of everything and if it's off at all you're popping out bearing balls, rubbing the rail, or not feeding the bearings smoothly, but it is the difference between feeling like a lowish drag slide or a greased up pig in a teflon ice rink. As for replacing the ball bearings * themselves in the carriages and re-greased everything in super-lube which didn't really affect them as much as adjusting the retaining wire, but did make them near silent for me.
Lots of youtube videos on reworking the carriages and why you should at least disassemble/ clean and re-grease them (at least the cheap ones) at a minimum. For the cost, a spare carriage block or two can save you a lot of frustration as well.
- replaced with 3/32" Inch Si3N4 Silicon Nitride Ceramic Ball Bearings G5 Balls, the G5 is important since it's the grade of the bearing, I chose non magnetic materials since I don't want them getting fouled by my magnetic arm mishaps which after removing them into a magnetic tray I'm confident it would have affected their performance.
-
@jim said in 6 axis delta 3D printer:
Hi @fma, I have the basic vertex models for the Robotdigg 2040 corners in Fusion360 format as was taking advantage of lots of quiet-time with lockdown to learn the product. Let me know if any use.
@jim, yes, I'm interested with your design. A step file would be ok...
Re the comment above on strength of the magballs/arms - I am just working though doubling up to 12-arms as need to support a Nema17 for my Clay extruder, six arms just about worked but would one would occasionally snap off when starting.
Not the cheapest solution, but I wanted the ease of magnetic attachment as need to remove the extruder for cleaning after prints. Should know in next couple of weeks how it goes.Mmm, that's an interesting solution. Thank's for sharing!
-
@fma - https://www.thingiverse.com/thing:4589432 has both STL and Step files. Let me know if you have any issues. I've not printed them as have the ALU versions from Robotdigg.
-
Perfect, thanks! I also plan to buy them from Robotdigg, it is just to integrate them in my design...
-
@fma said in 6 axis delta 3D printer:
@dc42, what about a delta with 2 moving plateforms using the same rails for the 2 sets of arms?
This is very close to what I've been thinking about lately, was just looking around to see if anyone had tried something like this and where they were up to.
What I have in mind is essentially two coupled delta effectors, but this is over-defined so the second set will just be two extra arms that orient a pivoting hot-end.
Anyway, this will be my first foray into the Duet/RepRapFirmware ecosystem, so thought I would say "hi". More questions to come, no doubt.
-
The frame for my test rig is coming along. Still waiting on the mainboard, belts and pulleys. Worth pointing out there are no magnets in this design - the push rods are under compression though the use of a tension spring or shock cord in this case. The same technique could be used for magnetic or spherical bearing type arms to augment the holding power or take up backlash/play.
-
@fma Is there a new update here or does the project no longer exist?
-
No, I didn't do anything. I bought a FLS SUN SR2 ! I may put a 2 axis (A/B) system on the bed, one day...
-
@teddphilipss The big problem I found is the clearance between the extruder and the rods, when the effector tilts. It needs a large effector. Or use a Bowden config, which I don't like very much (I will soon switch to a direct extruder on my FL SUN).
