Change feed rate during Z homing

OwenD

@deckingman said in Change feed rate during Z homing:

The older I get, the more my memory fails me but IIRC, DC's IR probe (being an analogue device) used to slow down the feed rate when the output reached a certain level (proximity to the bed). So if I'm right and my memory isn't playing tricks, then the firmware used to exist.

Well the docs for the sensor indicate that behaviour.
Doesn't prove you're not losing your marbles, but you should be able to find your keys 🤪

Always use a P value of 500. When the probe is triggered, the Z probe reading will be about 535. When it is slightly higher than the trigger height, the reading will be about 465. With a P value of 500, when the Duet sees the reading of about 465, it knows it is getting close to target height and it will slow down the Z motor.

dc42

@deckingman said in Change feed rate during Z homing:

Sure but that still involves two separate moves at different feed rates does it not? I was asking about one fluid move with a feed rate change after (or rather while) the first end stop triggers or is triggered. i.e. the Z move commences at a fast feed rate, continues at that feed rate until the first (optical) switch triggers, then finishes that same move at a lower feed rate.

What's wrong with using two separate moves? First a G1 H1 move using the optical switch as the endstop; then configure the nozzle switch to be the endstop instead and use a second G1 H1 move at a lower speed. The only difference is that the Z axis will stop when the first move finishes; but if the second move is at a slow speed, the stop may not be noticeable anyway.

deckingman

@dc42 said in Change feed rate during Z homing:

@deckingman said in Change feed rate during Z homing:

What's wrong with using two separate moves?
...........

There is nothing wrong with it all. But as I mentioned in my very first post which you don't seem to gave have bothered reading, I simply asked if it would be possible to replicate the behaviour of the IR probe, as that seems to be quite an elegant solution.

A simple "no it isn't possible" would have sufficed.

If I'd known that such a simple question would lead to an argument, I wouldn't have bothered asking the question.

deckingman

Sorry to re-visit this topic which seemed to cause such a furore, but I've started to commission my new printer and have additional data.

Homing moves to a switch, of necessity cannot have a deceleration phase. So the answer to the question "what is wrong with using two separate moves" is that when one has a large heavy bed weighing several Kgs, an instantaneous stop from even a modest speed such as 20mm/sec, results in a violent jerk which can cause belts to jump, thus destroying any bed levelling that might have been done, and in the longer term is likely to cause irreparable damage to both the lead screws and their nuts.

In the short term, I'll revert back to the original method of using the first end stop as a trigger and using a conditional loop to do a series of fast 100mm or so moves, and checking the trigger state after each iteration. This does involve even more moves, but at least each one begins and ends with an acceleration and a deceleration phase, thus preventing the violent and "damage causing" sudden stop.

In the longer term, and when funds allow, I might buy an IR probe and position this somewhere/somehow so that I can use this as the first end stop. This will/might give me the feed rate change that I was tentatively enquiring about in my opening post.

dc42

@deckingman said in Change feed rate during Z homing:

Homing moves to a switch, of necessity cannot have a deceleration phase. So the answer to the question "what is wrong with using two separate moves" is that when one has a large heavy bed weighing several Kgs, an instantaneous stop from even a modest speed such as 20mm/sec, results in a violent jerk which can cause belts to jump, thus destroying any bed levelling that might have been done, and in the longer term is likely to cause irreparable damage to both the lead screws and their nuts.

This is already logged as a requested enhancement on github, https://github.com/Duet3D/RepRapFirmware/issues/746.

@deckingman said in Change feed rate during Z homing:

In the short term, I'll revert back to the original method of using the first end stop as a trigger and using a conditional loop to do a series of fast 100mm or so moves, and checking the trigger state after each iteration. This does involve even more moves, but at least each one begins and ends with an acceleration and a deceleration phase, thus preventing the violent and "damage causing" sudden stop.

That sounds a good solution to me.

@deckingman said in Change feed rate during Z homing:

In the longer term, and when funds allow, I might buy an IR probe and position this somewhere/somehow so that I can use this as the first end stop. This will/might give me the feed rate change that I was tentatively enquiring about in my opening post.

I'm sorry, support for changing the feed rate during probing when using a probe with analog output was removed several versions ago. It was replaced with the ability to configure repeated Z probing using a faster feed rate the first time. I appreciate that this doesn't solve your issue.

T3P3 created this issue in Duet3D/RepRapFirmware

open Controlled deceleration when a homing switch is triggered #746

deckingman

@dc42 To be clear on the use case for this, I like to do all homing at reduced motor currents so that if a switch fails, the motor will stall before too much damage occurs. This is especially true in my case whereby I use the nozzle tip as the switch/probe with only about 5mm of movement in the kinetic mount. The hot end is a Slice Engineering Mosquito so too much upward pressure on the nozzle would cause extensive (and expensive) damage to the extremely thin walled heat breaks.

A realistic initial homing move for a screw driven heavy bed at reduced motor currents is about 300mm/minute (5mm/sec) and I follow this up with a fine homing move at 60mm/minute (1 mm/sec).

But I have about 600mm of vertical travel in the Z direction so if I had previously printed something that tall, it would subsequently take 2 minutes (600mm at 300mm/minute) just to do the initial Z homing. Hence the need/desire to do a much faster move, at full motor current, to get the bed somewhere close to the print head prior to homing proper.

The new slotted optical switch is more elegant than the older micro-switch on a swinging arm arrangement that I had before. I have now reverted back to the old way of doing things (a series of fast 80mm moves checking the status of the trigger at each iteration) and it is working well but the ability to change feed rate at a trigger point somewhere during one continuous move would be even more elegant.

The_Mechanic

@dc42
I nearly created a thread to ask for a solution like @deckingman and your post made me really happy!

I applied this method to my routine but it doesn't work like intended.
Where do I've the issue?

I'm using a Klicky probe on my Voron Switchwire and I want to make a fast probe to get down to the surface, afterwards I want to do three slow and accurate probes.

Here's my config and homez file

Would be really grateful for some tips or hints!

config.g

; Configuration file for Duet 3 Mini 5+ (firmware version 3)
; executed by the firmware on start-up
;
; General preferences
M111 S0
M575 P1 S1 B57600                                         ; enable support for PanelDue 
G21
G90                                                   	  ; send absolute coordinates...
M83                                                   	  ; ...but relative extruder moves
M550 P"Voron Switchwire"                                  ; set printer name
M669 K2 X-1:0:-1 Z-1:0:1

; Network
M552 S1                                               	  ; enable network
M586 P0 S1                                            	  ; enable HTTP
M586 P1 S0                                            	  ; disable FTP
M586 P2 S0                                           	  ; disable Telnet

; Drives
M569 P0.0 S0 D3	V0		
M569 P0.1 S0 D3 V0                                 	  	  ; physical drive 0.1 goes forwards
M569 P0.2 S1 D3 V0                                  	  ; physical drive 0.2 goes forwards
M569 P20.0 S1 D3 V0                                       ; physical drive 0.3 goes forwards
M584 X0.0 Y0.2 Z0.1 E20.0                    	          ; set drive mapping
M350 X16 Y16 Z16 E16 I1                              	  ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 		               			  ; set steps per mm
M92 E741.075
M566 X600.00 Y600.00 Z1000.00 E1200.00              	  ; set maximum instantaneous speed changes (mm/min)
M203 X30000.00 Y30000.00 Z30000.00 E10000.00              ; set maximum speeds (mm/min)
M201 X5000.00 Y5000.00 Z5000.00 E30000.00                 ; set max accelerations (mm/s^2)
M906 X1200 Y1700 Z1200 E650 I30                        	  ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                               	  ; Set idle timeout

; Axis Limits
M208 X0 Y-8 Z0 S1                             			  ; set axis minima
M208 X250 Y210 Z205 S0                         			  ; set axis maxima

; Axis compensation
;M556 S50 X0.10
;M579 X1.001717

; Endstops
M574 X1 S4                                    			  ; configure sensorless endstop for low end on X
M574 Z1 S2                                   			  ; configure sensorless endstop for high end on Z 
M574 Y2 S1 P"io5.in"                                      ; configure active-high endstop for low end on Y via pin io5.in

; Z-Probe
M558 K0 P5 C"^io6.in" H2 F4000 T9000 A1 S0.02   		  ; set Z probe type to unmodulated and the dive height + speeds
M558 K1 P5 C"^io6.in" H2 F100 T9000 A3 S0.01   			  ; set Z probe for a second and more accurate G30
G31 P5 X0 Y25                               			  ; set Z probe trigger value, offset and trigger height
G31 Z6.20

;Mesh grid
M557 X15:231 Y25:210 P7:7                        		  ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B3988              ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                        ; create bed heater output on out0 and map it to sensor 0
M307 H0 R0.274 K0.241:0.000 D12.01 E1.35 S1.00
M140 H0                                                   ; map heated bed to heater 0
M143 H0 S120                                              ; set temperature limit for heater 0 to 120C
M308 S1 P"20.temp0" Y"thermistor" T100000 B4725 C7.06e-8  ; configure sensor 1 as thermistor on pin 121.temp0
M950 H1 C"20.out0" T1                                     ; create nozzle heater output on 121.out0 and map it to sensor 1
M307 H1 B0 S1.00                                          ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S295                                              ; set temperature limit for heater 1 to 295C 

; Fans
M950 F0 C"20.out1" Q5000                                  ; create fan 0 on pin out3 and set its frequency
M106 P0 C"Part cooling"                           	      ; set fan 0 name and value. Thermostatic control is turned on
M950 F1 C"20.out2" Q5000                    	          ; create fan 1 on pin out2 and set its frequency, and tacho output on out2.tach
M106 P1 S1 H1 T50                                         ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                              	    	  ; define tool 0
G10 P0 X0 Y0 Z0                                      	  ; set tool 0 axis offsets
G10 P0 R0 S0                                         	  ; set initial tool 0 active and standby temperatures to 0C

; Miscellaneous
M950 S0 C"out6"						  	    			  ; assign GPIO port 0 to heater3 on expansion connector, servo mode
M280 P0 S154
T0                                                 	      ; select first tool
M150 X3
M98 P"/macros/neopixel/startup.g"

;; Global variables
M98 P"/macros/startup/set_globals.g"

; After startup
M98 P"/macros/startup.g"							 	  ;tone after config file was completely executed

homez.g

; Z-Home
M564 H0
G91                									  	 ; relative mode
G1 Z10 F2000     										 ; raise head 4mm to ensure it is above the Z probe trigger height
M564 H1
M98 P"/macros/zprobe/loadclicky.g"						 ; call macro to load the Klicky probe
M400													 ; Wait for current moves to finish
G90                									     ; back to absolute mode
G1 H0 X125 F10000 										 ; put head over the x-axis centre of the bed, or wherever you want to probe
G1 H0 Y90 F10000										 ; put head over the y-axis centre of the bed, or wherever you want to probe
;M558 P5 C"^io6.in" H2 F4000 T9000 A1 S0.02   			 ; set Z probe type to unmodulated and the dive height + speeds
G30 K0               	 									 ; lower head, stop when probe triggered and set Z to trigger height
;G4 P500
M400
G1 Z5 F1000
G30 K1
;M558 P5 C"^io6.in" H2 F100 T9000 A3 S0.01   			 ; set Z probe for a second and more accurate G30
G91
G1 Z15 F1000
M98 P"/macros/zprobe/unloadclicky.g"					 ; call macro to unload the Klicky probe
G90
G1 X0 Y0 F10000
M558 P5 C"^io6.in" H2 F500 T9000 A1 S0.01   			 ; set Z probe to standard back
M564 S1

dc42

@The_Mechanic said in Change feed rate during Z homing:

M558 K0 P5 C"^io6.in" H2 F4000 T9000 A1 S0.02 ; set Z probe type to unmodulated and the dive height + speeds
M558 K1 P5 C"^io6.in" H2 F100 T9000 A3 S0.01 ; set Z probe for a second and more accurate G30

Define just one probe, not two, like this:

M558 K0 P5 C"^io6.in" H2 F4000:100 T9000 A4 S0

F4000:100 tells it to probe at 4000mm/min for the first probe and 100mm/min for subsequent probes. A4 tell is to do at most 4 probes, and S0 tells it to always do all of them and average the results of the slow probes.

The_Mechanic

@dc42
Thank you very much!
It works like you pointed out and how it wanted it to behave.

But: one issue solved, another appeared...
When I'm doing a G29 before the print I'm having the same settings for those probings, which take nearly 4 times longer.

Is the solution to use
M558 K0 P5 C"^io6.in" H2 F1000 T9000 A1 S0 before the G29?

jay_s_uk

@The_Mechanic yes, you can make that change in bed.g at the beginning and then change it back at the end.