Hypercube Evolution
-
I just changed ?dl=0 to ?raw=1 in your Dropbox image URL to make it work. That's a nice looking printer!
-
Hey buddy.
Will look forward to hearing your progress as I'm building the same printer with a Duet Ethernet. I'm still awaiting some frame parts to build the main frame.
I'm going with a Titan Aero hot end to start with which will be different and a BLTouch.
Ian
-
When you think your setup needs wiring management you should see me printers, yours wiring already looks perfectly managed
-
Thanks to all.
David, Thank you and thank you!
Coolice, it has had it's moments I wanted to turn it into an end table. Only because I am new to the 3D Printing scene and there aren't any explicit instructions on assembling this. But once it's together it is absolutely rock solid. Good luck with yours and if I can be of any help please don't hesitate to ask.
MiR,
Ha! I am sure if you have a wiring problem, all of the wires are easily accessible, whereas mine would take some disassembling first!
-
Coolice, it has had it's moments I wanted to turn it into an end table. Only because I am new to the 3D Printing scene and there aren't any explicit instructions on assembling this. But once it's together it is absolutely rock solid. Good luck with yours and if I can be of any help please don't hesitate to ask.
Hey Buddy.
Yeah it's a pretty big build for newcomers to 3D printing. This one will be my second, but I have converted my CTC to MKS Gen V1.4 controller and changed the hot ends/extruders so I learnt a lot from that. The mechanical and electronics side I am ok with as I'm an engineer by trade and deal with electronics on a daily basis, so I just need to get my head around the firmware side of things.
I wouldn't mine seeing your Duet files if you get a chance please? I'd like to look at what you've setup and then figure out the why's to the various settings so I understand better what's going on.
Ian
-
Buddy, I just now saw this response. For some reason I don't get notifications from this forum when someone responds. So I have to go looking for it. If you still need my config files, here's a link to a dropbox folder.
https://www.dropbox.com/sh/dcdczf5cq09cs39/AACBRIgNsmSG8-aGHlyy6l0ua?dl=0
I included my config, bed, and homeall.g folders. If you need to see the others just ask.
I tried to remember to change the description at the end of each line, but I might have missed a couple. For instance in the section I set the drive direction. I changed them so many times trying to get the axes direction correct, I might have not put the proper description.If you need anything else, please let me know.
-
Nice, I'm trying to figure out my endstops on mine.. Seems the LED is always on unless I slip something in between it to trigger it. I tried asking for help on fb group but I'd love to get some help if at all possible. I can't wait
-
That sounds correct to me. I just finished building my HEVO a few days ago.
I'm using optical endstops, and I'm pretty sure the LED is on all the time except when they are homed. Have you tried doing a home yet, or are you not quite at that point? -
Nice, I'm trying to figure out my endstops on mine.. Seems the LED is always on unless I slip something in between it to trigger it. I tried asking for help on fb group but I'd love to get some help if at all possible. I can't wait
That is the normal way round for optical endstops. Use S1 in your M574 command.
-
Nice, I'm trying to figure out my endstops on mine.. Seems the LED is always on unless I slip something in between it to trigger it. I tried asking for help on fb group but I'd love to get some help if at all possible. I can't wait
That is the normal way round for optical endstops. Use S1 in your M574 command.
Thanks, I was able to get the x and y to trigger. it took me a little bit to figure out why they weren't doing anything before. basically I was having an issue where M119 wasn't showing it triggered. Once I looked more at the code and changed values here and there I finally got it working. Now I need to mount all of my endstops so that I can home the printer properly. currently I'm hitting home and stopping it shortly after with an object triggering the sensor.
