New firmware 1.20 Release Candidate 2 - please try it!

deckingman

Yes. If you send M584 P5 to make the additional axes visible, I think the extruder positions will magically correct themselves.

Confirmed. Sending M584 P5 makes the 20.0mm value magically jump two places to the left from D2 to D0. With the U and V axes visible, any commanded extrusion amount increments the position for the correct drive, Thanks.

Camalot977

@dc42:

Which firmware version were you upgrading from?

1.1.9 something

strips

Flashing RC3 yesterday wifi seemed to work properly and worked a few seconds after power up now and then this:

[...]
Recv: Error retrieving WiFi status message
Recv: Error retrieving WiFi status message
Recv: Error retrieving WiFi status message
Recv: Error retrieving WiFi status message
Recv: Error retrieving WiFi status message
Recv: Error retrieving WiFi status message
Recv: Error retrieving WiFi status message
[...]

Wifi debug does not give me any more info. Web server is dead.

M999 resets and I get connected to wifi:

Recv: FIRMWARE_NAME: RepRapFirmware for Duet WiFi FIRMWARE_VERSION: 1.20RC3 ELECTRONICS: Duet WiFi 1.0 + DueX5 FIRMWARE_DATE: 2017-12-16
Recv: ok
Recv: Wifi module is connected to access point Tomato24, IP address 192.168.1.111

Then 15-20 seconds later without doing anything is crashes again with lots of "Recv: Error retrieving WiFi status message"

This is a new one for me.

dc42

@strips, please follow the instructions at https://www.duet3d.com/forum/thread.php?pid=32944#p32944.

strips

David, that is what I did.

Connected to DuetWifi by USB (octoprint in bigbox). The M111 S1 P14 really does not give my anything after it failed. I need to try again and enable before it fails to see if I get anything before.

strips

Funny… not changing anything today everything works

So I have to call this one off for the moment

dc42

Please try the new 1.20RC4 and DWS 1.20RC1 that I have just released.

BMMal

The Machine Properties tab is not reporting the motor currents in RC4 or RC3. Not sure about earlier versions. Could be a DWC thing too I suppose?

justine.haupt

@dc42:

…
1. Use M140 H0:2:3:4 to configure multiple bed heaters, instead of M140 P0 H0, M140 P1 H3 etc.
...
Thoughts?

That sounds very good to me.

T-Printer

Hi I still a lot of problems to Connect, to my DuetWifi board, is just go on and off.
I Have install the new 1.20RC4 and DWS 1.20RC1, but NO, the only drifrence from RC3 I can see, is it now only reconnect once, the it say WiFi reported error: Timed out while trying to connect to ….

This is from Pronterface, and running a M111 S1 P14
Connecting...
Printer is now online.
WiFi reported error: Lost connection, auto reconnecting

M111 S1 P14
SENDING:M111 S1 P14
Debugging enabled for modules: WiFi(14)
Debugging disabled for modules: Platform(0) Network(1) Webserver(2) GCodes(3) Move(4) Heat(5) DDA(6) Roland(7) Scanner(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13)
WiFi reported error: Timed out while trying to connect to Nordbygaard
WiFi: sleep enable,type: 2
WiFi: sl
WiFi: scandone
WiFi: usl
WiFi: state: 5 -> 0 (0)
WiFi: rm 0
WiFi: pm close 7
WiFi: del if0
WiFi: usl
WiFi: mode : null

Any ide, what this can be?

Dougal1957

Don't understand why you installed a release candidate rather than the full release one https://www.duet3d.com/forum/thread.php?id=3817

T-Printer

Just to try is, because the full release do the same on and off. Now I an´m back to the full release.
From Pronterface:
SENDING:M111 S1 P14
Debugging enabled for modules: WiFi(14)
Debugging disabled for modules: Platform(0) Network(1) Webserver(2) GCodes(3) Move(4) Heat(5) DDA(6) Roland(7) Scanner(8) PrintMonitor(9) Storage(10) PortControl(11) DuetExpansion(12) FilamentSensors(13)
WiFi: bcn_timout,ap_probe_send_start
WiFi reported error: Lost connection, auto reconnecting
WiFi: ap_probe_send over, rest wifi status to disassoc
WiFi: state: 5 -> 0 (1)
WiFi: rm 0
WiFi: pm close 7
WiFi: scandone
WiFi: state: 0 -> 2 (b0)
WiFi: state: 2 -> 3 (0)
WiFi: state: 3 -> 5 (10)
WiFi: add 0
WiFi: aid 6
WiFi: cnt
WiFi:
WiFi: connected with Nordbygaard, channel 7
WiFi: dhcp client start…
WiFi: pm open,type:2 0
WiFi reported error: Timed out while trying to connect to Nordbygaard
WiFi: sleep enable,type: 2
WiFi: sl
WiFi: scandone
WiFi: usl
WiFi: state: 5 -> 0 (0)
WiFi: rm 0
WiFi: pm close 7
WiFi: del if0
WiFi: usl
WiFi: mode : null

To connect aging, I have to power off / on.

strips

On RC4 now and so far so good! Running through levelling and calibration routines because of a rebuild.

o_lampe

Maybe a bit late to claim an issue with RC4 now that it is officially released.
I have some G1 or G0 moves in the end code of the slicer to park the effector at X0 Y0 Z160.
These moves get misinterpreted by DWC and it always shows layer count 799. Thereby the estimated print duration based on
layer time x #layers is totally wrong too.
I tried G0 and G1 moves, both with same result.
If DWC would check for moves which include an extrusion, it would detect the last relevant layer.

Sorry, if that has been posted earlier, I'm not a regular visitor here…

dc42

That's a well-known issue. The solution is put a comment starting with ;E or ; E at the end of the G0 or G1 command line that does that movement.