Seems to be doing something : ))

[dc42]

@3mm said in Seems to be doing something : )):

Perhaps I should also mention that when I run "Mesh Grid Compensation" web-control 'preset', that while it does generate a bed map, the graphic display depicts only the axis and grid overlay with no measurements??

Hover the mouse cursor over the grid points to see the measurements.

[3mm]

@dc42

Hovering over the grid does nothing.

3mm

[3mm]

@dougal1957

The numbers changed! Was .109/.107 and now is consistently reading things like:
"Calibrated 8 factors using 17 points, deviation before 0.039 after 0.031"

I presume that these are better numbers than before.

There seems to have been some type of mismatch somewhere, I think it was between the config.g file and the config.json file, as I was seeing via the console, an error msg, when ever I did a calibration, being a G32 'bad command' error. I reran the RepRap wizard and the error msg disapeared. So what does the config.json file do that the config.g file doesn't? Which one is read by the firmware?

Thanks for your help.

3mm

[dc42]

@3mm said in Seems to be doing something : )):

Hovering over the grid does nothing.

3mm

In that image it isn't displaying a height map at all. Did that auto calibration fail?

[3mm]

@dc42 said in Seems to be doing something : )):

@3mm said in Seems to be doing something : )):

Hovering over the grid does nothing.

3mm

In that image it isn't displaying a height map at all. Did that auto calibration fail?

@dc42

No, that's what I've been saying. I've not seen anything on that grid in all of the runs that I've done. Its seems like its working ok?? and I'm not seeing any error messages anywhere. Both 'AutoCalibration' and 'Mesh Grid Compensation' macros run the entire process. It creates a height-map .csv file, but nothing is displayed? And hovering over it does nothing, and before I mentioned this matter...well...I tried zooming in, and out, rotating, panning. The grid is empty.

Here's the content of the most recent HeightMap.csv file that I generated today.

HeightMap.csv:
RepRapFirmware height map file v2, mean error -0.001, deviation 0.044
xmin,xmax,ymin,ymax,radius,xspacing,yspacing,xnum,ynum
-100.00,100.10,-100.00,100.10,111.80,20.00,20.00,11,11
0, 0, 0, -0.057, -0.049, 0.052, 0.040, 0.104, 0, 0, 0
0, 0, 0.017, -0.001, -0.008, 0.027, 0.007, 0.023, 0.027, 0, 0
0, 0.053, -0.019, -0.011, 0.020, 0.063, 0.026, 0.067, 0.075, 0.098, 0
0.085, 0.064, 0.037, 0.018, 0.013, 0.017, 0.019, 0.003, -0.096, -0.100, 0.012
0.051, 0.040, 0.012, -0.002, 0.002, -0.001, -0.010, 0.001, -0.013, 0.003, -0.006
0.066, 0.040, 0.017, -0.010, -0.034, -0.050, -0.049, -0.061, -0.058, -0.071, -0.073
0.014, 0.003, 0.003, -0.001, -0.034, 0.015, -0.048, -0.060, -0.043, -0.050, -0.068
-0.013, 0.010, 0.008, 0.041, 0.014, -0.063, -0.074, -0.071, -0.060, 0.025, -0.046
0, 0.041, 0.048, 0.050, -0.026, -0.047, 0.031, 0.032, 0.039, 0.051, 0
0, 0, -0.036, 0.020, -0.055, -0.060, 0.004, 0.004, -0.009, 0, 0
0, 0, 0, -0.032, 0.023, -0.037, -0.044, -0.023, 0, 0, 0

---

On an unrelated subject...I find it peculiar that the web 'G-Console' displays different messages than does the PanelDUE, in fact, there is an obvious disparity between the two readouts, eg, the web 'G-Console' and the PanelDUE 'Console'. It would be convenient to watch the PanelDUE 'Console' display for messages while the web-interface remains in Machine-Control or another mode.

Thanks...3mm

[dc42]

What browser are you using? Also, please confirm what firmware and DWC versions you are using.

[3mm]

@dc42

Hi...

Web-Browser: Mozilla - FireFox 'Quantum' v57.0 (64-bit)

PanelDUE: v1.20(15b1)
DUET-E HW v1.02
Smart-Effector v?

RepRap FW for Duet 2 WiFi/Ethernet
HW Electronics: Duet Ethernet 1.02 or later
FW Ver: 1.21 (2018-03-21)
Web Interface Ver: 1.15a

thanks...3mm
ps...screen grab of 'Machine-Control' page:

[dc42]

You are running a very old version of DWC. Please upgrade it to 1.21.

[3mm]

@dc42

I'm confused, I thought I had the latest Firmware...which of these two firmwares are you refering?

FW Ver: 1.21 (2018-03-21)
Web Interface Ver: 1.15a

The web-interface, presume is an internal module of the DUET-E firmware v1.21, do I need to manually update that firmware? eg, 1.15a?

thanks...3mm

[3mm]

@dc42

Also, which specific (DUET-E v1.02 HW, SAM4E8E) firmware do you recommend? I'd appreciate the URL location, so as not to make any mistakes.

thanks...3mm

[Dougal1957]

This is the link to the file you need to Download then drag the .zip file (do not unzip it) to the Upload button on the settings page of the web interface

DWC V 1.21

[3mm]

@dougal1957 & @dc42

Thanks guys, that fixed the graph anomally!!

What about the latest FW releases? I notice some releases at URL:
https://github.com/dc42/RepRapFirmware/tags
depict a 'verified' tag, while other's don't? What's the difference, are the un-'verified' beta or not-necessarially-stable test releases?

Thanks in advance

3mm

[dc42]

@3mm said in Seems to be doing something : )):

I notice some releases at URL:
https://github.com/dc42/RepRapFirmware/tags
depict a 'verified' tag, while other's don't? What's the difference, are the un-'verified' beta or not-necessarially-stable test releases?

That is correct.

[JoergS5]

This post is deleted!