Where Log messages
-
Hi,
i am having troubles with temp, excesive hot, and i have upgraded firmware to:
- 2.0(RTOS) (2018-06-05b3)
But i can't find log messages, in version 1.21, they appear in console...
Where i can find these error messages, that Duet generates with overtemperature?
And
There is some method of view drivers temps? If Duet send a message with hihg temperature has reached, this mean, that cant follow this temp. No?
Thanks
-
Here is a link to a similar question about monitoring driver temps.
https://forum.duet3d.com/topic/5507/detect-overheated-driver/3
-
-
@timcurtis67 Thanks
-
@peirof Messages on the console, noting that the temperature in the motors is high
-
@peirof are you sure that the stepper drivers are ovettemperature. What does M122 report?
-
Hi,
i have put a big fan, 120 mm 24v, over drivers in duet, the results of M122.
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.0(RTOS) running on Duet WiFi 1.02 or later
Board ID: 08DGM-95BNL-MGPSN-6JKDL-3S06L-92W7W
Used output buffers: 3 of 20 (9 max)
=== RTOS ===
Static ram: 28380
Dynamic ram: 95940 of which 16 recycled
Exception stack ram used: 436
Never used ram: 6300
Task NETWORK ready, free stack 324
Task HEAT blocked, free stack 1256
Task MAIN running, free stack 3560
=== Platform ===
Last reset 01:25:34 ago, cause: power up
Last software reset at 2018-06-27 11:36, reason: User, spinning module GCodes, available RAM 6312 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0041f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 88.2ms
MCU temperature: min 39.1, current 43.8, max 44.3
Supply voltage: min 24.2, current 24.5, max 24.9, under voltage events: 0, over voltage events: 0
Driver 0: ok, SG min/max 0/166
Driver 1: ok, SG min/max 0/201
Driver 2: ok, SG min/max 0/188
Driver 3: ok, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Date/time: 2018-06-27 13:10:11
Slowest loop: 34.95ms; fastest: 0.07ms
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 170, MinFreeDm 120, MaxWait: 60509396ms, Underruns: 0, 0
Scheduled moves: 74920, completed moves: 74902
Bed compensation in use: mesh
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.0
Heater 2 is on, I-accum = 0.3
=== GCodes ===
Segments left: 1
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 X-27.782 Y1.683 E3863.46408" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 90.77ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.21
WiFi MAC address 2c:3a:e8:0b:05:a1
WiFi Vcc 3.35, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 13992
WiFi IP address 192.168.1.200
WiFi signal strength -60dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Expansion ===
- WiFi -
-
@peirof the drivers are not reporting a temperature issue and the CPU is cool.
