• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

Z-offset is very high

Scheduled Pinned Locked Moved
Third-party add-ons
2
9
1.0k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    hevilp
    last edited by hevilp 8 Aug 2018, 17:21 8 Aug 2018, 17:06

    Hi,

    I got a the v1.2 from precision piezo uk as endstop.

    I use:
    M558 P8 I1 R0.4 F300 Z1

    My homez.g:

    G91 ; relative mode
    G1 Z4 F400 ; lowers bed 4mm to avoid dragging nozzle over the bed
    G90 ; back to absolute mode
    G1 X200 Y180 F4000 ; Move probe to middle of bed
    G30 ; probe
    G91 ; relative mode
    G1 Z4 F150 ; move slowly 4mm in the +Z direction
    G90 ; back to absolute mode
    G30 ; probe
    G1 Z2.5 F150 ;Move Z to 2.5 above the bed
    ;G31 X0 Y0 Z-0.15
    G90 ;back to absolute
    ; G1 X0 F4000 ;move to X0

    The probe is very nice and I use a high sensetive.

    When do "G1 Z0" the nozzle goes a little bit into the bed.
    When I do G30 the carriage is not moved when the nozzle touches the bed.

    Why G30 and G1 Z0 differs so much?
    If I want to correct that, I need a very high negative offset or?

    1 Reply Last reply Reply Quote 0
    • undefined
      Phaedrux Moderator
      last edited by Phaedrux 8 Aug 2018, 17:24 8 Aug 2018, 17:21

      G30 uses the values from M558 and will tell the system where z0 is, G1 will not.

      Have you calibrated the zprobe trigger offset? https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe#Section_Calibrate_the_Z_probe_trigger_height

      What does the G31 command look like in your config.g?

      Z-Bot CoreXY Build | Thingiverse Profile

      1 Reply Last reply Reply Quote 0
      • undefined
        hevilp
        last edited by 8 Aug 2018, 17:25

        With G30 I do my Z-Probe right?

        M558 P8 I1 R0.4 F300 Z1
        means: If the piezo gets triggered, there is Z0, right?

        1 Reply Last reply Reply Quote 0
        • undefined
          Phaedrux Moderator
          last edited by 8 Aug 2018, 17:36

          That is correct, but you first need to tell the system where the nozzle is in relation to the bed when the probe triggers using G31 Zn. In the case of the piezo probe Zn is a slightly negative value normally, but you can't be sure until you do a trigger height calibration as described in the link I posted.

          Z-Bot CoreXY Build | Thingiverse Profile

          1 Reply Last reply Reply Quote 0
          • undefined
            hevilp
            last edited by 8 Aug 2018, 17:40

            I did all in your link, it comes -0.14. and I got it in my homez.g "G31 X0 Y0 Z-0.14", not in my config.g. (Like before).Of course I always do a G28 so it is set always.

            1 Reply Last reply Reply Quote 0
            • undefined
              hevilp
              last edited by hevilp 8 Aug 2018, 17:57 8 Aug 2018, 17:46

              Do I need G92 with piezo? In normal case, everytime when the piezo is triggered, something between 0,05 and 0,15mm over the triggerpoint is Z0 or? Maybe my error is depending on my other thread, that G31 is always 0. The offset is ignored I think

              1 Reply Last reply Reply Quote 0
              • undefined
                Phaedrux Moderator
                last edited by 8 Aug 2018, 18:03

                @hevilp said in Z-offset is very high:

                G31 X0 Y0 Z-0.14

                This should be in your config.g

                Z-Bot CoreXY Build | Thingiverse Profile

                1 Reply Last reply Reply Quote 0
                • undefined
                  hevilp
                  last edited by 8 Aug 2018, 18:09

                  @phaedrux said in Z-offset is very high:

                  G31 X0 Y0 Z-0.14

                  Okay, I will move it, if I set it manually, even for X or Y, it always reports 0. I just updated to the latest firmware, and there is it always 0, too.

                  undefined 1 Reply Last reply 8 Aug 2018, 18:19 Reply Quote 0
                  • undefined
                    Phaedrux Moderator @hevilp
                    last edited by 8 Aug 2018, 18:19

                    @hevilp See your other thread for why it reports 0.

                    If you send G31 T8 it will report the current settings.

                    Z-Bot CoreXY Build | Thingiverse Profile

                    1 Reply Last reply Reply Quote 0
                    8 out of 9
                    • First post
                      8/9
                      Last post
                    Unless otherwise noted, all forum content is licensed under CC-BY-SA