Printer dosen't start the print job correct

AS-3D Druck

@phaedrux
If i disable stall detection nothing works anymore cause there are no physical Endstops anymore.

The positioning for the Nozzle is absolut yes (G90) and the Extrusion aswell.
BTW. i got the issue on 2.01 aswell so i thought maybe it is fixed in 2.02 but i remember that i printed with 2.01 so maybe my
Slicer(Simplify 3D) is differten than my last (before Windows broke).

Strange cause i used the last gcode to configure my profile correct. (on every gcode it lists as a comment the configuration of the Profile).

//Edit:
Ok a old gcode File that i found on my printer works so it is my Profile that has a issue BUT there is a nother Problem:
23:15:28Error: motor phase A disconnected on drivers 2

It posts this every few seconds:
23:18:11Error: motor phase B disconnected on drivers 2
23:18:06Error: motor phase B disconnected on drivers 2
23:18:01Error: motor phase A disconnected on drivers 2
23:17:57Error: motor phase B disconnected on drivers 2
23:17:17Error: motor phase A disconnected on drivers 2
23:17:07Error: motor phase A disconnected on drivers 2
23:16:21Error: motor phase B disconnected on drivers 2
23:15:44Error: motor phase A disconnected on drivers 2
23:15:38Error: motor phase A disconnected on drivers 2
23:15:33Error: motor phase A disconnected on drivers 2
23:15:28Error: motor phase A disconnected on drivers 2

It is connected btw.
What can/should i do?

Found that so it is a Firmware Thing that i can ignore in that Version (it looks like)
https://forum.duet3d.com/topic/6707/duet-error/14

Phaedrux

Those look like spurious error messages that are a known issue in the 2.02 RC release. Go back to the previous 2.01 full release or the 2.02 beta release and try again.

AS-3D Druck

If it dosen't damage my Printer or do something else it dosen't matter right?

dc42

@as-3d-druck said in Printer dosen't start the print job correct:

If it dosen't damage my Printer or do something else it dosen't matter right?

The spurious messages don't matter. If you were getting them on just one phase then I would suggest you have a genuine problem; but getting them on both phases when the motor is moving slowly (e.g. the Z axis moving just a little to do bed compensation) is not unusual in this release candidate.

In previous releases, the open load detection has been disabled because of spurious indications. I was hoping to get it working in this release to help diagnose bad motor connections.

AS-3D Druck

@dc42 and what could you say about that my printer starts and stops after my purgeline and home it self?

dc42

@as-3d-druck, I would need to see an example GCode file that causes that behaviour when you try to print it.

AS-3D Druck

@dc42 Ok, here is the Thing that i tryed to print: https://cloud.as-3ddruck.de/index.php/s/pcfzPngPzMj3c3e

Phaedrux

I think I see your problem.

From your gcode file:

;Put printing message on LCD screen
M117 D-Bot Printing...
G92 E0
G1 E-5.0000 F3600
G1 Z1.000 F1002
; process dbot
; layer 1, Z = 0.200
M104 S0 ; turn off extruder
M140 S0 ; turn off bed
G91 ; use relative coordinates
G1 Z0.6 F5000 ; lift nozzle by 0.6mm
G90 ; use absolute coordinates
G28 X0 ; home X axis
G1 Y100 ; move Y axis to end position
M84 ; disable motors
M107 ; turn off fan
T1
; tool H0.200 W0.408
; skirt

Right before starting the skirt under the heading process dbot layer 1, it disabled your motors and turns off the heaters and fan. It looks like maybe your end gcode script is being inserted into the start of your file.

AS-3D Druck

@phaedrux said in Printer dosen't start the print job correct:

I think I see your problem.

From your gcode file:
;Put printing message on LCD screen
M117 D-Bot Printing...
G92 E0
G1 E-5.0000 F3600
G1 Z1.000 F1002
; process dbot
; layer 1, Z = 0.200
M104 S0 ; turn off extruder
M140 S0 ; turn off bed
G91 ; use relative coordinates
G1 Z0.6 F5000 ; lift nozzle by 0.6mm
G90 ; use absolute coordinates
G28 X0 ; home X axis
G1 Y100 ; move Y axis to end position
M84 ; disable motors
M107 ; turn off fan
T1
; tool H0.200 W0.408
; skirt
Right before starting the skirt under the heading process dbot layer 1, it disabled your motors and turns off the heaters and fan. It looks like maybe your end gcode script is being inserted into the start of your file.

Why does my Slicer this?

Phaedrux

Simplify3D? Check your various gcode insertion areas. Maybe something got copy and pasted into the wrong place?

AS-3D Druck

@phaedrux said in Printer dosen't start the print job correct:

Simplify3D? Check your various gcode insertion areas. Maybe something got copy and pasted into the wrong place?

Did that anf for some Reason i got the Endscript in the Toolchanging Section in S3D but i don't know why it was there.
Anyway thx for you're help.
Printer is now back in the Game.

Phaedrux

Glad it got sorted out.