You're D-Bot looks way cleaner than my.
Is the 3 Leadscrew System woth it?
I got 2 with a BLTouch as a probe and i'am not shure if the 2 Leadscrews are not good enough or the Z Probe is crap.

THX i totaly missed that Feature.
But maybe a Visual Interface on the Webinterface or something to start that Command (on the drop Down Menu of Autobed Compensation) would be awesome.

Hello Guys,

i've got "maybe" a stupid Question.
For what is the Filament Tab in the latest Version of the Interface?

@phaedrux said in Stall detection tweeking from 2.05 to 3.3.0 RC3:

But sounds like you got it working now?

Yes, i can provide my new Home X and Y File + Config if someone wants to look at it. (Troubleshooting etc.)

homex.g

M913 X50 Y50               ; drop motor current to 50%
M400                       

G91                        ; relative positioning
G1 H2 Z10 F12000           ; lift Z relative to current position

G1 H1 X-500 F5000          ; move quickly to X axis endstop and stop there (first pass)
;G1 H2 X20 F12000            ; go back a few mm
;G1 H1 X-500 F5000          ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-10 F6000           ; lower Z again

G90                        ; absolute positioning
M400
G1 X150                    ; moves X to the Middle
M913 X100 Y100             ; return current to 100%

homey.g

M913 X50 Y50                           ; drop motor current to 50%
M400 

G91                                    ; relative positioning
G1 H2 Z10 F12000                       ; lift Z relative to current position

G1 H1 Y-500 F5000                      ; move quickly to X axis endstop and stop there (first pass)
;G1 H2 Y20 F12000                        ; go back a few mm
;G1 H1 Y-500 F5000                      ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-10 F6000                       ; lower Z again

G90                                    ; absolute positioning
M400
G1 X150 Y120                           ; moves X to the Middle
M913 X100 Y100                         ; return current to 100%

config.g

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon Jun 14 2021 19:09:40 GMT+0200 (Mitteleuropäische Sommerzeit)

; General preferences
G90                                            ; send absolute coordinates... 
M83                                            ; ...but relative extruder moves
M550 P"D-Bot"                                  ; set printer name
M669 K1                                        ; select CoreXY mode
M671 X-21.4:356.4 Y165:165 S20 P1.5            ; leadscrews at left (connected to Z) and right (connected to E1) of X axis

; Network
;M551 P"Duet"                                  ; set password
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet

; Drives
M569 P0 S1                                     ; physical drive 0 goes forwards
M569 P1 S1                                     ; physical drive 1 goes forwards
M569 P2 S1                                     ; physical drive 2 goes forwards
M569 P3 S1                                     ; physical drive 3 goes forwards
M569 P4 S1                                     ; physical drive 4 goes forwards
M584 X0 Y1 Z2:4 E3                             ; set drive mapping (2 Z Motors = 2 & 4)
M92 X79.40 Y79.40 Z397.20 E492.45              ; set steps per mm //X&&Y 78.43
M350 X128 Y128 Z128 I0                         ; configure microstepping without interpolation
M350 E64 I1                                    ; configure microstepping with interpolation
M566 X900 Y900 Z12 E120                        ; set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z500 E1500                    ; set maximum speeds (mm/min)
M201 X3500 Y3500 Z300 E2500                    ; set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E1200 I30               ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X335 Y191 Z350 S0                         ; set axis maxima

; Stall Detection
M915 X Y S12 F0 R1							   ; S=Sensitivity (higher=less sensetive)//started at 10//; F=Filtering; R=Action

; Endstops
;M574 Z1 S0                                    ; Define active low and unused microswitches
M574 X1 S3                                     ; Define Endstops for Stall Detection //Before X3 Y3
M574 Y1 S3                                     ; Define Endstops for Stall Detection //Before X3 Y3

;Filament Run Out Sensor
M591 D0 P2 C3 E6.0  ; Tool 0 Extruder 0 

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4700 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                               ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4680  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                   ; set temperature limit for heater 1 to 280C

; Z-Probe
M950 S0 C"exp.heater3"                         ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000            ; set Z probe type to bltouch and the dive height + speeds
G31 P600 X-30 Y0 Z1.6      ; (P25 before)      ; set Z probe trigger value, offset and trigger height
M557 X30:304 Y20:191 S40                       ; define mesh grid

; Nozzle + Filament
M404 N2.85 D0.400

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"PartCooling" S0 H-1                  ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 C"Heatsink" S1 H1 T45                  ; set fan 1 name and value. Thermostatic control is turned on
M950 F2 C"fan1" Q500                           ; create fan 2 on pin fan1 and set its frequency
M106 P2 C"AlwaysOn" S1 H-1                     ; set fan 2 name and value. Thermostatic control is turned on

; Tools
M563 P0 S"e3D V6" D0 H1 F0                     ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
T0                                             ; select first tool
M80                                            ; Turn On Power Supply

I just reduced the current by 50% and commented out the 2. attempt to home X or Y and tryed differen Sensitivitys and here we go.

Okay i got it now kind off.
My Problem was i got in my config before (2.05) steps M92 and after that M350 for interpolation on those steps etc. but in this config as you can see before i got it the other way around.
So i changed that and now i got movment back.

The only thing that i try to fix is now why it runs to the set direction is on the End and still tackles it a few times and than sets back to the middle as intended.

I currently try to change the sensitivity but still not great.
M915 X Y S6 F0 R1

//EDITE:
Got it now on 4 and it seems to work

@phaedrux said in Stall detection tweeking from 2.05 to 3.3.0 RC3:

The Z moves are the only place where H2 is correct. H1 means seek the endstop. H2 means move the motor regardless if it's homed or not.

I tryed this for now with no moving Axis.

M400

M913 X50 Y50 ; drop motor current to 50%

M400 G91; relative positioning

G1 H2 Z10 F12000 ; lift Z relative to current position

G1 H1 X-400 F6000 ; move quickly to X axis endstop and stop there (first pass)

G1 H2 X5 F12000 ; go back a few mm

G1 H1 X-320.5 F4000 ; move slowly to X axis endstop once more (second pass)

G1 H2 Z-10 F6000 ; lower Z again

G90 ; absolute positioning

M400

G1 X150 ; moves X to the Middle

M913 X100 Y100 ; return current to 100%

M400

@phaedrux said in Stall detection tweeking from 2.05 to 3.3.0 RC3:

X3 Y3 is not valid. It must be either 1 or 2. 1 is low end of travel, 2 is high end of travel. S3 is correct though for stall detection.
https://duet3d.dozuki.com/Wiki/Gcode?revisionid=HEAD#Section_M574_RepRapFirmware_Num_3

fixed that

; Endstops
M574 Z1 S0                                    ; Define active low and unused microswitches
M574 X1 S3                                 ; Define Endstops for Stall Detection //Before X3 Y3
M574 Y1 S3                                 ; Define Endstops for Stall Detection //Before X3 Y3

@phaedrux said in Stall detection tweeking from 2.05 to 3.3.0 RC3:

M574

yea shure

config.g

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon Jun 14 2021 19:09:40 GMT+0200 (Mitteleuropäische Sommerzeit)

; General preferences
G90                                           ; send absolute coordinates...
M83                                           ; ...but relative extruder moves
M550 P"D-Bot"                                 ; set printer name
M669 K1                                       ; select CoreXY mode
M671 X-21.4:356.4 Y165:165 S5 P1.5            ; leadscrews at left (connected to Z) and right (connected to E1) of X axis

; Network
;M551 P"Duet"                               ; set password
M552 S1                                       ; enable network
M586 P0 S1                                    ; enable HTTP
M586 P1 S0                                    ; disable FTP
M586 P2 S0                                    ; disable Telnet

; Drives
M569 P0 S1                                    ; physical drive 0 goes forwards
M569 P1 S1                                    ; physical drive 1 goes forwards
M569 P2 S1                                    ; physical drive 2 goes forwards
M569 P3 S1                                    ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                              ; set drive mapping
M350 X256 Y256 Z256 I0                        ; configure microstepping without interpolation
M350 E16 I1                                   ; configure microstepping with interpolation
M92 X78.43 Y78.43 Z398.00 E492.45             ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00           ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00       ; set maximum speeds (mm/min)
M201 X500.00 Y20.00 Z250.00 E250.00           ; set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E1200 I30              ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                       ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                              ; set axis minima
M208 X335 Y191 Z350 S0                        ; set axis maxima

; Stall Detection
M915 X Y S10 F0 R0

; Endstops
M574 Z1 S0                                    ; Define active low and unused microswitches
M574 X3 Y3 S3                                 ; Define Endstops for Stall Detection

;Filament Run Out Sensor
M591 D0 P2 C3 E6.0  ; Tool 0 Extruder 0 

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4700 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                         ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00                              ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                       ; map heated bed to heater 0
M143 H0 S120                                  ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4680  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                          ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                              ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S280                                  ; set temperature limit for heater 1 to 280C

; Z-Probe
M950 S0 C"exp.heater3"                        ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H5 F120 T6000           ; set Z probe type to bltouch and the dive height + speeds
G31 P600 X-30 Y0 Z1.6      ; (P25 before)     ; set Z probe trigger value, offset and trigger height
M557 X30:304 Y20:191 S40                      ; define mesh grid

; Nozzle + Filament
M404 N2.85 D0.400

; Fans
M950 F0 C"fan0" Q500                          ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"PartCooling" S0 H-1                 ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                          ; create fan 1 on pin fan1 and set its frequency
M106 P1 C"Heatsink" S1 H1 T45                 ; set fan 1 name and value. Thermostatic control is turned on
M950 F2 C"fan1" Q500                          ; create fan 2 on pin fan1 and set its frequency
M106 P2 C"AlwaysOn" S1 H-1                     ; set fan 2 name and value. Thermostatic control is turned on

; Tools
M563 P0 S"e3D V6" D0 H1 F0                    ; define tool 0
G10 P0 X0 Y0 Z0                               ; set tool 0 axis offsets
G10 P0 R0 S0                                  ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
T0                                            ; select first tool
M80                                           ; Turn On Power Supply

change S3 to H1 on the homex

; This File is just for testing the "stall detection" Feature.
; It might need to be adjusted to get it to work with you're Printer/s
 
; Sensorless Homing test file for RepRapFirmware on D-Bot
; M915 X S3 F0 R1

; More about M915 and how to set it up you can find here: 
; https://duet3d.com/wiki/G-code#M915:_Configure_motor_stall_detection

; Lift Z relative to current position
G91
G1 Z10 F6000 H1
G90

; Setup Stall Detection on CoreXY for Xmin Xmax
M400							; make sure everything has stopped before we make changes
; M574 X3 Y3 S3						; set endstops to use motor stall
M913 X30 Y30						; reduce motor current to 50% to prevent belts slipping
G91							; use relative positioning
G1 H1 X-500 F4000					; move the X to max until it detects the min Point
G92 X0							; set X min Point
;G1 S2 X30							; move X away from min Point
M400							; wait untill X is done
G1 H1 X500 F4000					; move the Y to min until it detects the min Point
;G1 S2 X-30						; move X away from max Point
M208							; shows the way that has been traveled
G90							; back to absolute positioning
M400							; make sure everything has stopped before we reset the motor currents
M913 X100 Y100 Z100					; motor currents back to normal
; M574 X1 Y2 Z1 S0					; set endstops back to normal (is maybe different than you're normal)

G1 H1 X150

; Lift Z relative to current position
G91
G1 Z-10 F6000 H1
G90

btw. those {1} are not actualy in the code might be a Bug with this Forum.

Output in Console:
G28 X
Error: Homing failed
It dosen't want to move Z even.

@jay_s_uk no Idea?

@jay_s_uk yes

Hi there Guys,

i just finished it to update my Firmware from 2.05 to 3.3.0RC3 and got a small Problem.

This is how i homed my X Axis:

; This File is just for testing the "stall detection" Feature.
; It might need to be adjusted to get it to work with you're Printer/s
; Sensorless Homing test file for RepRapFirmware on D-Bot
; M915 X S3 F0 R1
; More about M915 and how to set it up you can find here: 
; https://duet3d.com/wiki/G-code#M915:_Configure_motor_stall_detection
; Lift Z relative to current position
G91
G1 Z10 F6000 S2
G90
; Setup Stall Detection on CoreXY for Xmin Xmax
M400							; make sure everything has stopped before we make changes
; M574 X3 Y3 S3						; set endstops to use motor stall
M913 X30 Y30						; reduce motor current to 50% to prevent belts slipping
G91							; use relative positioning
G1 S3 X-500 F4000					; move the X to max until it detects the min Point
G92 X0							; set X min Point
;G1 S2 X30							; move X away from min Point
M400							; wait untill X is done
G1 S3 X500 F4000					; move the Y to min until it detects the min Point
;G1 S2 X-30						; move X away from max Point
M208							; shows the way that has been traveled
G90							; back to absolute positioning
M400							; make sure everything has stopped before we reset the motor currents
M913 X100 Y100 Z100					; motor currents back to normal
; M574 X1 Y2 Z1 S0					; set endstops back to normal (is maybe different than you're normal)
G1 S1 X150
; Lift Z relative to current position
G91
G1 Z-10 F6000 S2
G90

And it does nothing and just says:

Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
Error: Homing failed

I tryed H1 instead of those S Commands, but it didn't worked for me.
How can i fix that?

@dc42 okay thx, but i installed RC3 already so it is okay for me i guess.

@phaedrux
I turned it off and on again and M115 gave me the Firmware Version i installed before.
(So 3.2.2)

Yes, i installed 3.3RC3 right after that.