Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Zortrax M200 Duet Conversion

    Scheduled Pinned Locked Moved
    General Discussion
    13
    99
    25.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • dc42undefined
      dc42 administrators
      last edited by

      Sounds good! My thoughts:

      1. If you will be using a plug/socket for the hot end, then I suggest you use a 4-wire configuration for the PT100 to guard against the contact resistance increasing. Just get a microfit 3.0 connector with a couple of extra ways, which is what I did when I upgraded to PT100.

      2. Depending on how non-flat and flexible the existing bed is, and whether it would be possible and safe to use clips around the edge, you might get away with putting a sheet of 4mm glass on top and printing on that.

      3. When you come to upgrade the bed, I advise against using a 240V heater if you want to disconnect the bed when the print has finished, because of the difficulty of making it safe. Your bed heater is only 160W so it is easily powered from 24V, and you already have a 24V PSU providing adequate power. You could order an EcoCast plate to your required size from http://www.aluminiumwarehouse.co.uk/cutting_calc.php and attach a 24V silicone heater to the underside and a thermistor or another PT100 in a hole at the edge. Make the bed plate a little larger than the heater and the print area to leave room for fixings.

      My preferred arrangement for small to medium size print beds is glass clipped on top of aluminium, with or without a thin sheet of PEI attached to the top of the glass. The PEI is painted black on the underside for compatibility with the IR sensor. The glass can be unclipped from the bed plate when the print is finished.

      Duet WiFi hardware designer and firmware engineer
      Please do not ask me for Duet support via PM or email, use the forum
      http://www.escher3d.com, https://miscsolutions.wordpress.com

      1 Reply Last reply Reply Quote 0
      • Corexyundefined
        Corexy
        last edited by

        Cheers David,

        That ally cut place is a hot tip! Cheers for that.

        A 240x240mm piece of 8mm thick "eco cast" (I'm assuming that's the precision flat one?) for 13 quid!!

        Sold at that price, I'll drill and tap the thing myself.

        I'll use the 4 wire method you showed in your blog for the PT100, but I'm thinking to solder it straight on without a plug at all for best results. It's not like I'll be expecting to change it frequently. I actually have 4 pin microfits as well but bugger it. Will 28AWG wires be OK over 1.5M?

        Yeah…copy that on the AC heater. Bit too ambitious for my little printer, and Keenovo have an off the shelf 200x200 24v/200w that should give that little more kick. Especially under ally without the extra thick Zortrax perfboard to heat.

        https://www.aliexpress.com/store/product/200X200mm-200W-24V-w-NTC-100K-Thermistor-Keenovo-Silicone-Heater-3D-Printer-Heater-Heatbed-First-Grade/210086_32327554677.html

        Can I just rely in the thermistor in the silicone heat mat?? Does the DuetWifi software allow me to calibrate the temperature reading to show the actual temperature I take on the build surface using a thermometer probe? I'd hoped to set the hotend temp the same way as well.

        I'd prefer not to use glass and am keen to try the Printbite, as I print a lot with ABS up around the 260 deg mark, and am pretty much on the same page as Digital Dentist regarding ABS printing requirements (no offense meant). It seems to be get good reviews providing it's set up all level at the right nozzle height, and I'm pretty particular setting those up.

        Bit of a pain sitting around waiting for little bits and pieces to arrive when you're all keen to fire it up…..

        1 Reply Last reply Reply Quote 0
        • dc42undefined
          dc42 administrators
          last edited by

          I use the thermistor built in to the silicone bed heater on my delta printer. It works, but it over-reads somewhat because it is close to the heater wires and not in good contact with the bed plate. So I have to set the temperature somewhat higher than I really want, but I have got used to that. Also it gives slightly strange heater tuning results because the system has 2 time constants instead of just one as the heater model assumes. A 3mm cartridge thermistor or PT100 set in a hole drilled into the edge of the plate would be more accurate.

          If you intend to connect the PT100 sensor without using a connector, then a 2 wire connection should be adequate. To work out the effect of 3m of 28AWG wire, work out its resistance. One ohm of resistance gives a temperature error of 2.5C. If you use a 4-wire connection, the wiring resistance doesn't matter.

          Duet WiFi hardware designer and firmware engineer
          Please do not ask me for Duet support via PM or email, use the forum
          http://www.escher3d.com, https://miscsolutions.wordpress.com

          1 Reply Last reply Reply Quote 0
          • Corexyundefined
            Corexy
            last edited by

            @dc42:

            I use the thermistor built in to the silicone bed heater on my delta printer. It works, but it over-reads somewhat because it is close to the heater wires and not in good contact with the bed plate. So I have to set the temperature somewhat higher than I really want, but I have got used to that. Also it gives slightly strange heater tuning results because the system has 2 time constants instead of just one as the heater model assumes. A 3mm cartridge thermistor or PT100 set in a hole drilled into the edge of the plate would be more accurate.

            If you intend to connect the PT100 sensor without using a connector, then a 2 wire connection should be adequate. To work out the effect of 3m of 28AWG wire, work out its resistance. One ohm of resistance gives a temperature error of 2.5C. If you use a 4-wire connection, the wiring resistance doesn't matter.

            Thanks very much for that.

            So a PT100 drilled into the plate it is then.

            I'll use 4 wires both in the extruder and heat bed sensors.

            I understand the single daughter board can run 2 PT100's? Is that correct?

            I like the idea of accurate sensors on both the bed and extruder, might as well do it right.

            I went looking for sensors with 4 wires standard.

            Seems I can get longer ones in 3mm, which might be nice for the heat bed as it'd cover more area?

            http://au.rs-online.com/web/p/platinum-resistance-temperature-sensors/7621143/

            Seems this one only goes up to 200 degrees? Are all PT100's the same?

            In 10mm long (for the extruder block) it seems I can only get 2 wire, so I'd need to solder wires on as per the DC42 blog?

            https://littlebirdelectronics.com.au/products/pt100-temperature-sensor-probe

            Here's an ebay one with wires long enough to go straight through to the board:

            http://www.ebay.com/itm/3D-Printer-Ultimaker-2-PT100-B-Thermocouple-Sensor-M3-15mm-Germany-chip-/301925619850

            If anyone has links for what would be the very best option, please feel free to put them up.

            1 Reply Last reply Reply Quote 0
            • dc42undefined
              dc42 administrators
              last edited by

              Yes the PT100 daughter board supports 2 sensors.

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              1 Reply Last reply Reply Quote 0
              • Corexyundefined
                Corexy
                last edited by

                @dc42:

                Yes the PT100 daughter board supports 2 sensors.

                Thank you.

                You beat me to it, I've edited some more questions in above.

                1 Reply Last reply Reply Quote 0
                • dc42undefined
                  dc42 administrators
                  last edited by

                  The only PT100 sensor I have used is the E3D one. Do you have a distributor for E3D in Australia?

                  There are in theory two slightly different sorts of PT100 sensor, based on European and American standards, but according to Wikipedia the American standard isn't used much these days.

                  Duet WiFi hardware designer and firmware engineer
                  Please do not ask me for Duet support via PM or email, use the forum
                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                  1 Reply Last reply Reply Quote 0
                  • Corexyundefined
                    Corexy
                    last edited by

                    What's the best way to go with the fans for the Duetwifi?

                    I'm assuming 24v was the way to go, regardless of being always on or controlled?

                    The Zortrax is weird in the way that it uses a big 24v fan to cool the board (always on), but then uses 12v for the heat break and print cooling fans.

                    I'm happy to use 24v all round if that's the best way to go.

                    From what I've read it's got to be all the one voltage for this board?

                    1 Reply Last reply Reply Quote 0
                    • deckingmanundefined
                      deckingman
                      last edited by

                      Yes fans are all 24v. If you want to use the Zortrax 12v fans, you can do so by using a 24vdc to 12vdc converter.

                      Edit. That's assuming that you are using a 24v power supply. Basically, the fans are whatever voltage you are powering the duet with.

                      Ian
                      https://somei3deas.wordpress.com/
                      https://www.youtube.com/@deckingman

                      1 Reply Last reply Reply Quote 0
                      • Corexyundefined
                        Corexy
                        last edited by

                        @deckingman:

                        Yes fans are all 24v. If you want to use the Zortrax 12v fans, you can do so by using a 24vdc to 12vdc converter.

                        Edit. That's assuming that you are using a 24v power supply. Basically, the fans are whatever voltage you are powering the duet with.

                        Thank you.

                        I'll just buy new 24v fans rather than add a converter.

                        Really struggling with fitting this IR probe anywhere near the nozzle.

                        I'm assuming I can set the 5 (I'll just use 5 points for this small bed) locations of the level checking function in the firmware?

                        1 Reply Last reply Reply Quote 0
                        • deckingmanundefined
                          deckingman
                          last edited by

                          @Corexy:

                          Really struggling with fitting this IR probe anywhere near the nozzle.

                          Me too. I have a great big fat cone shaped diamond hot end nozzle. The best I can do is offset to one side by about 17mm. Not ideal but I'll have to live with it.

                          Ian
                          https://somei3deas.wordpress.com/
                          https://www.youtube.com/@deckingman

                          1 Reply Last reply Reply Quote 0
                          • Corexyundefined
                            Corexy
                            last edited by

                            @deckingman:

                            @Corexy:

                            Really struggling with fitting this IR probe anywhere near the nozzle.

                            Me too. I have a great big fat cone shaped diamond hot end nozzle. The best I can do is offset to one side by about 17mm. Not ideal but I'll have to live with it.

                            Yeah, I'm looking at about the same distance at back of the nozzle.

                            Too much stuff to tuck in all around the hot end.

                            Been at it with the prototypes all day, but might have the final take on the printer right now (hopefully).

                            1 Reply Last reply Reply Quote 0
                            • Dougal1957undefined
                              Dougal1957
                              last edited by

                              When you do the probing file make sure the probe points go round the bed in a clockwise direction (Viewed from above) and the finish with the centre one

                              Doug

                              1 Reply Last reply Reply Quote 0
                              • Corexyundefined
                                Corexy
                                last edited by

                                Bit further along.

                                Mounted the board with the antenna facing the ventilation holes, in the hope that I can sit my portable wifi dongle right beside the printer and get a reasonable connection.

                                All existing cables that are being used have been fitted with plugs to suit the Duet, time to start running all the wires up to the hot end. I'll be taking a bit of time/care with the wiring loom so it's all laid out very neatly and secured nicely at each end.

                                Despite looking like they are pulled tight, the stepper motor cables are quite loose….I even went for another look after seeing the picture lol. Optical illusion.

                                Got my dual fan/IR probe housing almost perfect (never mind the crap brown filament, I'm using it up on prototyping). The probe is miles from the nozzle but I don't care as I'll be using a precision cast ally build plate with Printbite on top, which I'll level manually with a feeler gauge like I always have.

                                Fans fitted are dodgy old 12v's I had laying around while I wait for my 24v fans to arrive.

                                1 Reply Last reply Reply Quote 0
                                • Corexyundefined
                                  Corexy
                                  last edited by

                                  One concern though….

                                  I can position the nozzle for setting the height in the start so that it's over the build plate, but if I'm using the full plate for a big print the sensor will be outside the edge of the plate over open space.

                                  Is that going to be a problem??

                                  My understanding is that it's just used for level checking and setting the nozzle height for the first layer, and that after that the layer heights are set by the steps of the Z axis stepper.

                                  Is that correct?

                                  1 Reply Last reply Reply Quote 0
                                  • dc42undefined
                                    dc42 administrators
                                    last edited by

                                    You can configure the XY offsets of the nozzle from the probe in the G31 command in config.g. Then all you need to do is choose bed probing points to put in bed.g that the probe can actually reach.

                                    Duet WiFi hardware designer and firmware engineer
                                    Please do not ask me for Duet support via PM or email, use the forum
                                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                                    1 Reply Last reply Reply Quote 0
                                    • Corexyundefined
                                      Corexy
                                      last edited by

                                      @dc42:

                                      You can configure the XY offsets of the nozzle from the probe in the G31 command in config.g. Then all you need to do is choose bed probing points to put in bed.g that the probe can actually reach.

                                      Thank you,

                                      I understand that I can set the bed probing points, but as the print progresses past the first layer is it all right if the probe is outside the edge of the build plate?

                                      1 Reply Last reply Reply Quote 0
                                      • dc42undefined
                                        dc42 administrators
                                        last edited by

                                        @Corexy:

                                        I understand that I can set the bed probing points, but as the print progresses past the first layer is it all right if the probe is outside the edge of the build plate?

                                        Yes, as long as it doesn't collide with anything or short against anything.

                                        Duet WiFi hardware designer and firmware engineer
                                        Please do not ask me for Duet support via PM or email, use the forum
                                        http://www.escher3d.com, https://miscsolutions.wordpress.com

                                        1 Reply Last reply Reply Quote 0
                                        • Corexyundefined
                                          Corexy
                                          last edited by

                                          @dc42:

                                          @Corexy:

                                          I understand that I can set the bed probing points, but as the print progresses past the first layer is it all right if the probe is outside the edge of the build plate?

                                          Yes, as long as it doesn't collide with anything or short against anything.

                                          No worries there, cheers.

                                          1 Reply Last reply Reply Quote 0
                                          • Corexyundefined
                                            Corexy
                                            last edited by

                                            Just putting my wiring loom that will replace the "Z" ribbon cable together.

                                            I've got:

                                            4x 24awg for the extruder stepper
                                            2x 20awg for the heater
                                            4x 28awg for the PT100 (I've chosen to use the 4 wire configuration)
                                            4x 28awg for the print and heat break fans
                                            3x 28awg for the IR sensor

                                            All wire is silicone insulated RC wire, and I've done them in bundles as listed above with little bits of heatshrink every 6 inches to keep them from getting unruly.

                                            I'll use either the spiral wrap or blue mesh tube shown around the lot.

                                            Just wondering if there'll be any interference/signal issues having them all side by side??

                                            I'd assume not, as the ribbon cable carries them all, but I thought I'd ask.

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA